First few hundreds are sold. See here a picture of 1 of my hashing cards:  |
|
|
|
Hey guys, I received the refund now. But I will start the refund distribution in 24hours - This timeframe is for you to check if the payout adresses in the table is right - If its right you dont have to do anything, if not just shout me a PN:  I will send this message also via PN to all participants. Thanks for your patients. cheers Foofighter |
|
|
|
|
have you tried to use another slot on mboard?
|
|
|
|
|
you are right, the back side is prefered but from temp measurements there isnt so much difference between both sides in temp.
I ordered new heatsinks because many people asked for it, should have them in hand in 1-2 weeks.
So Iam open for new orders here.
cheers
Foofighter
|
|
|
|
|
I have offered small heatsinks here a few weeks ago- but have none left-
If there is interest I could order some more ? I offered them for about 0,1btc per 16 small sinks excluding shipping (shipping was about ~0,05)
But as this is not really a profit based thing, I would only order again if there is interest from enough people on GB basis.
Foofighter
|
|
|
|
I tried it again with theses adapters http://piborg.org/triborg. But still no luck  (again connected it directly after testing). |
|
|
|
News: Bitcentury has got our devices and they will start shipping tomorrow or beginning of next week  |
|
|
|
News: Bitcentury hat die Geräte erhalten und wird diesen Freitag oder Anfang nächste Woche versenden wenn alles gut läuft. grüße |
|
|
|
|
news:
bizwoo got the refund today.
He just needs to distribute it now and then I can also refund all of you asap
Foofighter
|
|
|
|
|
n1, auf welchen OHM Wert bist du runtergegangen?
grüße
|
|
|
|
Good NewsBG1 refund was finally received. I am sending the list for GB1 refunds to John K now for him to start asap refunding the buyers. As I mentioned before we will not be held responsible for wrong btc addresses in the list, etc. good news bizwoo! great. |
|
|
|
There is no problem with the cable itself, but somehow the connection of the cable doesnt work Havent found out why, maybe someone who got his already has a solution? |
|
|
|
|
definatly too high if another card is behind the card with the sink.. in a full setup I would suggest heatsinks with an height of 10-max15mm
|
|
|
|
Two quick questions on the goxxed info. 1) What points are you using exactly to measure the altered voltage? I am leery to probe around the board while powered up for fear of shorting something. 2) What exactly is reniceing and why is it important to reduce? This is the first time I have seen this term used in the bitfury threads. Thanks very much and awesome work!  Meanwhile I have a stable nonce rate of average >35 Gh/s on both boards - so time to give something back: You can measure the voltage on nearly every capacitor on the board, I usually use the bigger ones directly beside the DC/DC converter, left to the coil (the bigest part on the board). There are not many ways to do something wrong, just make sure to not shorten your probes, as there are 30+ Amps available. (I have exactly 0.840 Volts there with 55er clocks and it looks very stable, although there is no easy way to measure the real current draw on the core voltage and confirm that everything is inside bounds.) BTW: I also reported about a mysterious chip, which usually throws lots of errors, but sometimes recovers completely after a longer uptime. When running this board alone or in switched order with the other one, the errors of this single chip also disappear. Hi, thanks for sharing. Can you also confirm the Ohm values given above? |
|
|
|
Hey marto,
could you add 4pin connection cables to you shop for chaining miners?
cheers
Foofighter
Could you please answer that? |
|
|
|
|
Current status:
We are still waiting for chip refund from avalon
|
|
|
|
|
@barntech
If I only got 1 drillbit board , Can I run it without a backplane?
|
|
|
|
|
Show Posts
