 Show Posts
|
|
Pages: « 1 2 [3] 4 5 »
|
|
I'm thinking of buying an Antminer A3. Do you think that it will continue to be profitable for a few months?.
|
|
|
|
|
Hi, do you know why this huge increase in difficulty and network hashrate?. I suppose it will be due to the arrival of the new Obelisk miners and the Halong Mining Dragon Mint. It is right?.
Regards.
|
|
|
|
with climb you mean pump
Yes!. Climb?, what climb?, ;-). |
|
|
|
|
Spectacular pump of Siacoin!!!.
|
|
|
|
 How much do you think the A3 is left alive until it stops giving benefits?.
Depends on your electricity cost. Hummm, That's a problem, mine is very high. More or less, about 0.17USD kw/h. Here we steal with electricity. |
|
|
|
|
How much do you think the A3 is left alive until it stops giving benefits?.
|
|
|
|
Hi!. The difficulty is going up a lot. Do you know what the cause is? Are new miners connecting?.
Regards.
It is a combination of the batch 3 Antminers testing along with Innosilicon S11 miners testing before they get shipped out. The sia network in getting flooded by all these retards to the point that no one will make a profit from buying the asics. Have not the Innosilicon S11 miners yet been delivered?. I thought it was all sold, except the new A3 batch. Regards. |
|
|
|
|
Hi!. The difficulty is going up a lot. Do you know what the cause is? Are new miners connecting?.
Regards.
|
|
|
|
|
Any news of change of algorithm to CryptonightV7 of Karbo (KRB), Electroneum (ETN), Bytecoin (BCN), Dinastycoin (DCY) and DigitalNote (XGN)??.
Are there other coins with cryptonight algorithm?.
Is it still viable to buy a baikal for about $ 1000?.
Best regards.
|
|
|
|
Hi!. I think that is the obelisk manufacturer. I had them mining,  . And it seems that he has already sent them to his buyers. Best regards. |
|
|
|
I ran my A3 overclocked at 930 Gh/s average for over one month with (low hardware errors under 2k/day per board)
I used 120V power on APW3++ and it worked like a charm!
Temperatures averaged around 62-65C for boards and outside room temps were between 60F-80F
I would say bitmain's PSU is stronger than it seems and does work well!
This is a dangerous example, since overloading the power supply may end up breaking it. The input circuit in the APW3++ is designed to be able to handle max. 1200W at 110-120V and max. 1600W at 220-240V mains voltage. I've also been running miner around 900-930 Gh/s (Overclocked from 600-650) and the power doesn't go above 1200W, it stays around 1180W on my A3's. Temps on boards are around 88C-93C with good air circulation and before at room temperature the miners would run stock at 80C-85C. After talking to Bitmain support the boards can run up to 115C before overheat protection kicks in but I would not like for the boards to get above 95C. Hi!. How to get a power of 1180-1200W?. When I set the A3 to 650, my power is at about 1450W!!. Do you have an APW3 power supply?. Did bitmain tell you that the board supports up to 115C ?. I think it's a very high temperature.. Anyway, when I put more than 640, it starts to give a lot of errors and the hashrate fluctuates a lot. Best regards. I'm using an APW3 power supply. What I did was overclock to 650 then after the settings are changed I rebooted the miner. When it first comes up I can see the power spike to over 1400W and then after a few hours it slowly settles in at around 1180W-1200W. Yes bitmain support said the chips on the boards are rated for 115C but from my background in computers I wouldn't recommend going over 100C. All miners are different but mine seem to like to be at around 650-662 which appears to be the limit of the boards because any higher they start to get lots of errors. Sure?. Humm, I don’t understand. I have configured my A3 with 662. I have restarted. And after a few hours my power consumption is 1500W and does not go down there. So, I do not know how you can get it down to 1200W. Currently, the fans are in 5010, the pcb in 63,61,65 C and the chips in 85,75,80 C. Best regards. |
|
|
|
|
Hello,
In the last 24 hours, my reward has been 820 sia, with one A3. This is getting worse.
Regards.
|
|
|
|
I ran my A3 overclocked at 930 Gh/s average for over one month with (low hardware errors under 2k/day per board)
I used 120V power on APW3++ and it worked like a charm!
Temperatures averaged around 62-65C for boards and outside room temps were between 60F-80F
I would say bitmain's PSU is stronger than it seems and does work well!
This is a dangerous example, since overloading the power supply may end up breaking it. The input circuit in the APW3++ is designed to be able to handle max. 1200W at 110-120V and max. 1600W at 220-240V mains voltage. I've also been running miner around 900-930 Gh/s (Overclocked from 600-650) and the power doesn't go above 1200W, it stays around 1180W on my A3's. Temps on boards are around 88C-93C with good air circulation and before at room temperature the miners would run stock at 80C-85C. After talking to Bitmain support the boards can run up to 115C before overheat protection kicks in but I would not like for the boards to get above 95C. Hi!. How to get a power of 1180-1200W?. When I set the A3 to 650, my power is at about 1450W!!. Do you have an APW3 power supply?. Did bitmain tell you that the board supports up to 115C ?. I think it's a very high temperature.. Anyway, when I put more than 640, it starts to give a lot of errors and the hashrate fluctuates a lot. Best regards. |
|
|
|
Hello,
What strategy are you following with sia coins?, are you holding them or are you trading to BTC?.
Best regards.
Holding for now Really not selling any but I think my ideal strategy will be hold a percent, swap some for other coins to hold to diversify, and sell some to pay for mining power ... Hi!, your proposal is interesting. I have everything still in altcoins, but I think that we would have to sell something to make a profit and pay for mining power. What method do you use to convert it to USD? Regards!. |
|
|
|
Have theory that A3 was build on D3 and this is the reason some A3 (including mine) have problems with hash boards - appears/disappears, hashing/no hashing, all asics few only and then turning 0000 into xxxx... Nothing is helping to solve: rebooting, restarting, resetting, plugging / unplugging, each by one, separately, adding two AWP++ , changing controller cables 1/4, 2/4, 3/4, 4/4 Even flashing ( thank you blissz) - NOTHING But funny my D3 with A3 firmware turns into A3 miner, even connects to the SIA pool, but not hashing and after moment all asics turns xxxx This suggest than sia network or "brick attack" on 24th is not the real problem. The real is that bitmain cleaned D3 stock transforming them into A3 thought ____ NOW the funny moment. If/when somebody finds out hot to avoid that wall to make D3 (with A3 firmware) hashing on SIA network....  ....... ALL D3 would finally be able to deliver ROI Actually been working this angle, have a pretty good idea of what makes a miner a D3 or and A3, but i need a D3 to test or someone with a D3 to send me some data to try to turn my A3 into a D3. There's pretty good reasons for bitmain to do something like this if they could. It would massively increase profits for them to have a ASIC chip that could be re-seeded to different algos. Also if you want to dump firmware the bitmain way... nanddump -f /initramfs.bin.SD /dev/mtd8 nanddump -f /am335x-boneblack-bitmainer.dtb /dev/mtd6 nanddump -f /uImage.bin /dev/mtd7 nanddump -f /u-boot.img /dev/mtd4 You'll have to hex edit those files afterwards and remove the trailing FF's to make them exactly like bitmain sends them out. Hi! I have read that you are working for convert your A3 in a D3. Have you been able to advance something?. Best regards!. |
|
|
|
|
Hello,
What strategy are you following with sia coins?, are you holding them or are you trading to BTC?.
Best regards.
|
|
|
|
It seems to be bac, I found in the antminer web interface that diff was 1024 instead of 512 when it didn't work.
Yep, working now. So strange... It may have been a temporary error of siamining pool. Is someone mining with luxor mining pool https://mining.luxor.tech?. Do you know how it works and the rewards it gives?. Regards!. |
|
|
|
Hello good news new design will be active in 5 days. All funds and accounts are transferred to the new software  Thank you for your patience. Trust us on this subject to be added back to the lost funds Hello, Why my coins are missing in current web site???. Best regards. Hello there is a Software bug. This is why our team is doing new software, everything will be fine, we would like to wait a very short time. Hello, I have logon in the new web site from outletbit, but I don'y found my PNX coins in balance. On 15 febrery, I have deposited 872 PNX in Outletbit Exchange. I have been to trying trade, but appears this message: You don't have enough PNX to sell. Please check your balance! What’s the problem?. And my coins are disappearing!. Where are my coins?. Please, can you help me?. Can you give me my coins?. Mi trade key is af741f14a289453350476bf004e0674a Regards. |
|
|
|
Hello good news new design will be active in 5 days. All funds and accounts are transferred to the new softwareThank you for your patience. Trust us on this subject to be added back to the lost funds Hello, Why my coins are missing in current web site???. Best regards. Hello there is a Software bug. This is why our team is doing new software, everything will be fine, we would like to wait a very short time. Hello, today, your web site has an error 503: Server Error
503
Service Temporarily Unavailable
The server is temporarily unable to service your request due to maintenance downtime or capacity problems. Please try again later.
What about the new website???. Best regards. |
|
|
|
|
