Show Posts
|
Pages: « 1 2 [3] 4 »
|
hi there.. i had a problem with an antminer s9 and i mailed support. they sent me a firmware for my S9 (that was broken) to try it out and see if it help my surprise was that this firmware has Fan control and i could set the fan to 100% my question is. its safe to install it on my others S9? the customer guy said that this firmware could damage my machine if it was purchase after oct 1.. what u guys think?
|
|
|
Try to oil the fan if that didn't work you should replace it.
u know if "fan 3" is back or front fan?
|
|
|
Have you plugged them in the right way around? Im guessing when you cleaned them you have plugged the fans back in different connectors on the controlboard
yeah they are connected in the right place. im still getting 1440/1800 rpm on "fan 3" thats front fan right?
|
|
|
but its weird that front fan was running slow now is the back one that is running slow and the front one is now running at normal speed..
|
|
|
You sould periodically clean your miners as dust builds up and coats the heatsinks and fns as youve found out. Switch it off and clean everything and see how you get on.
i did it.. but one of the fan is still slow.. its stuck on 1800rpm and wont increase
|
|
|
so its a normal behaviour for a diying fan ? it goes from 1680 to 3700 rpm.. it was working at like 4500 without droping..
EDIT: after cleaning it it works now.. but now the other one is slower.. wtf
|
|
|
hi im having problem with my antminer S9 one of the fans is running realy low and its making my miner go to temps above 88 grades heres a pic https://s24.postimg.org/5nyr76jjn/Untitled.jpgthis miner been running for like 2 months and no problems both fans turns on but one is realy slow
|
|
|
well i have a big problem with this shitty company i bought some s9 in november.. and one of them came with the controller board faulty.. i sent it back for warranty 1 month and a week later it arrived after it arrived 9 hours later a hash board broke (dont know why i have more s9 working just fine), i contacted then back and sent the hashboard again now after 2 weeks they reply that i have to send the whole machine back because i purchase it after 1 octuber now what makes me angry? the customer support told me to ONLY send the hash board i have this on mail.. i already lost 2 month of work with that antminer increasing the time ill go ROI.. they sent me a 12.93ths antminer and i bought 2 13ths that time.. the other one is hashing at 13.2 and this one that 9 hors that worked was working at 12.3 now my real problem is i dont have anymore money to pay shipment since where im from its realy realy expensive like 200$ i already paid like 300$ in the control board and hashboard.. now with the shole machine it should be like 200 or 250$ can anyone here give advice of what should i do ? i want to take legal action against them but i just want to fix my damn antminer and keep working.. here is the mail from BARBARA
|
|
|
reconnect the wire.. and stop cutting random wires. It will drive the fan, but then cuts off the sensing to said fan so it's unsure of the fans rpm, thinks it's off, and shuts down the miner
i tried reconecting the cable already but still not working.. here is what it does when i connect it http://youtu.be/RyfUlgTclVg(my other S9 is working just perfect after cutting the cables) btw the miner is shutting off, it just stay ON..
|
|
|
i found a solution cutting the blue cable from the fans, i tried with the front one and it worked when tried with the back one the antminer stoped working.. i hear the fans but no lights turn on and i cant connect to it.. any help plz?
|
|
|
hi, i just got my antminers S9 but they are working at temps over 100, but all my S7 are working under 50 temp, i have good cooling, (with s9 i can not edit the fan speed and its realy quiet it might be the problem) is there a way to activate this setting ?
Have you tried resetting them?? Not sure how on an S9 but im sure it will be in the manual somewhere. Looks like you have autotune s9's What version of firmware are you running? What is the speed on the label? The new 11-29 firmware should work well for you with cooler temps. No fan setting on the new autotunes, it figures out what the speed should be. where can i see the firmware version? and what speed and label are u talking about?
|
|
|
I read a little while ago that awesome miner had trouble with S9 miners as the S7 runs cgminer and the S9 runs BMminer and awesmemminer software had trouble loading the correct values.
yeah they already updated it for S9
|
|
|
Have you read the S9 thread. The S7 reports board temps and the S9 reports board and chip temps. Are you sure you are reading the same temps on each type of machine?
yes i have a program named awesomeminer, where i have temps of all miners in one GUI
|
|
|
This has been beat to death, no real solutions thus far aside from bypassing and direct wiring the fans control. Which leaves it blaring 24/7
hi is there a guide to do this?
|
|
|
Firstly I see you have posted this question already in the CORRECT thread for the S9 already. Please wait for a response in there. You will need to provide more information, batch number, firmware version, even if the fans are original (any markings).
i just upgrade the firmware, its the lastest batch 13 TH, original fan everythig is brand new. sorry about double post.. the other one have so many post maybe mine will be unoticiable.
|
|
|
hi i just receive some antminers S9, but i cant edit their fan speed.. the fan speeds are realy slow and im getting high temps, i was getting 50/60 with my s7 now getting over 100 with S9 but its because fan speed.. any fix for this?
|
|
|
why i cant max fan speed manually in S9 but i can in S7?
|
|
|
hi, i just got my antminers S9 but they are working at temps over 100, but all my S7 are working under 50 temp, i have good cooling, (with s9 i can not edit the fan speed and its realy quiet it might be the problem) is there a way to activate this setting ?
|
|
|
probare clevermining.. la has probado que tal es ?
|
|
|
any advice on that? i have some things i dont understand ppl tell me to mine zetacoin, neoscoin, peercoin and not btc
my question is do iget more profit mining something else?
i tried 1 day of peercoin i got 33% less from it
tried neoscoin 2 hours didnt make a cent
im using coinwarz so i know what coin is higher than btc the thing is all those coin take way longer than btc (pps) to farm can u educate me?
is there something else i should be loking beside that if certain coin is higher in exchange than btc?
what u guys think about clevermining?
if u guys could explain me all this conserns as if im a 5 years old boy i would apreciate it alot!
i got an s7 just to start, planing on get some S9 after i understand everything i should know, (free elec and money to spare)
NOTE: this is not a post about if i should or should not mine, all i want to know how to mine more efficiently
thank you.
|
|
|
|