A bit off topic, but I have a card which keeps crashing not just the miner, but the whole computer after a few minutes/hours randomly;
The card is a 780 Ti sitting with 5 x 750 Ti and whatever I do or whichever fork I use, it crashes the miner which start stressing the cpu at 100% (at which point the GPU usage is 0% for all cards) and after a few minutes without forcibly closing the miner, they PC just freezes, no BSOD, no restart, just completely loses interactivity. If I close the miner before that, the System process completely hogs one CPU core (25%, i3) and the PC becomes very unresponsive and it can barely do anything until a restart. Tried different risers, a few different drivers, replaced the GPU BIOS, downclocked but none of that helped. It only does that during mining and the PSU can't be the culprit.
The event log wasn't much of a help:
The description for Event ID 13 from source nvlddmkm cannot be found.
Graphics Exception: ESR 0x506224=0x80000041 0x506228=0x10a40f 0x50622c=0x280 0x506234=0x0
NVRM: Graphics TEX Exception on (GPC 0, TPC 4): TEX NACK / Page Fault
How big and what kind of PSU do you have? Just curious I had a problem with one before that caused all kinds of issues until I replaced it. |
|
|
|
Coins been in wallet for a little over 12 hours, how long do they take to start staking?
Anyone? 24 h OC, My post might have been lost, but what if I have less than 20 Balls on your pool? Can I still withdraw them since the tx is 20 balls? |
|
|
|
|
@ ocminer
Quick question about withdrawel fee.
I see the 20 Ball tx fee to withdraw. What if we don't have that many in the pool? Do I owe you to withdraw?
|
|
|
|
@ dodgedarkdev
Not sure if this has been mentioned or just an issue on my end.
I am using the wallet v1.2 but after I open it and sync up I have to close and reopen for the transaction to show up in my balance.
I am getting all my coins it's just that the total doesn't move until I close and reopen.
What platform are you using? Windows, Mac, or Unix? Windows 7 64bit |
|
|
|
|
@ dodgedarkdev
Not sure if this has been mentioned or just an issue on my end.
I am using the wallet v1.2 but after I open it and sync up I have to close and reopen for the transaction to show up in my balance.
I am getting all my coins it's just that the total doesn't move until I close and reopen.
|
|
|
|
Not sure if all you miners from Europe have seen this but here you go: http://www.ecoinmining.eu/news/bitcoin-wallet-platform-coinbase-opens-europe/Quote from inside article "The 13 countries Coinbase is adding include Italy, Spain, France, Belgium, the Netherlands, Austria, Cyprus, Finland, Greece, Latvia, Malta, Portugal, and Slovakia." |
|
|
|
still don't understand what was your opencl lib error, because the miner for nvidia doesn't use opencl
I am not the sharpest tool in the shed so I might have been doing or trying something I should not have. I'll place the blame on myself. |
|
|
|
@ djm34
Stupid question for you. This miner doesn't allow us to solo mine from one computer to the other, does it?
Was just curious because the skminer allows that.
which one ? (it should in principle as it uses the same code) From post 1,445: https://bitcointalk.org/index.php?topic=657601.msg9287828#msg9287828When I try your new one I get this "The procedure entry point clRelease could not be located in the dynamic link library OpenCl.dll" EDIT: When I run it on the rig with the wallet, it starts but closes after a few seconds. Tried to add pause but no message comes up. It just sits there. not sure what to see on post 1445. which opencl version is there on your computer ? may-be a problem with the version you are using... Sorry, I thought you meant what miner I was using to solo mine. That is what that post was for. I'll try and update the opencl and see if that helps (I have no idea what version I am on). that was my question and still is (however I assume it is the amd one), because there is no link to any amd miner on that post. The amd miner was released later on. However all the miners (amd/prime/nvidia) use the same logic to connect to the wallet. So if it works for one, it should work for the others. Re-downloaded the miner from the cuda thread and all is working fine now. Solo mining from Rig 1 to Rig 2 with no problems. Will send more coins to you after I find some more blocks. Thanks |
|
|
|
@ djm34
Stupid question for you. This miner doesn't allow us to solo mine from one computer to the other, does it?
Was just curious because the skminer allows that.
which one ? (it should in principle as it uses the same code) From post 1,445: https://bitcointalk.org/index.php?topic=657601.msg9287828#msg9287828When I try your new one I get this "The procedure entry point clRelease could not be located in the dynamic link library OpenCl.dll" EDIT: When I run it on the rig with the wallet, it starts but closes after a few seconds. Tried to add pause but no message comes up. It just sits there. not sure what to see on post 1445. which opencl version is there on your computer ? may-be a problem with the version you are using... Sorry, I thought you meant what miner I was using to solo mine. That is what that post was for. I'll try and update the opencl and see if that helps (I have no idea what version I am on). |
|
|
|
@ djm34
Stupid question for you. This miner doesn't allow us to solo mine from one computer to the other, does it?
Was just curious because the skminer allows that.
which one ? (it should in principle as it uses the same code) From post 1,445: https://bitcointalk.org/index.php?topic=657601.msg9287828#msg9287828When I try your new one I get this "The procedure entry point clRelease could not be located in the dynamic link library OpenCl.dll" EDIT: When I run it on the rig with the wallet, it starts but closes after a few seconds. Tried to add pause but no message comes up. It just sits there. |
|
|
|
|
@ djm34
Stupid question for you. This miner doesn't allow us to solo mine from one computer to the other, does it?
Was just curious because the skminer allows that.
|
|
|
|
Any plans to get on Bittrex? I think this coins would do really well on that exchange.  soon or later, they will add DOGED, spread the word, join the community,  indeed, they will accept us, we got higher daily volume then most of the coins at bittrex. But for now its good without bittrex. I concur. Too many bots on BitTrex. |
|
|
|
|
@ djm34
Thanks for the miner. Sent you some blocks.
Transaction ID: xxxxxxxxxxxxxxxxxxxxde7a29f503f83f70703639fc649acaf2e48cd50519b0607de238d743d66 7267bc1b04cf0cf63f9636c7208b2fffbea832ea896107bc3
Should be there shortly.
|
|
|
|
mine is like at 10% or even less
Are you running Linux. I get up to 60 % usage on my cpu with a low of 30%. |
|
|
|
I have 2x Palit GTX 970 delivered yesterday, not impressed so far, think they might be going for a return trip back up the river in a couple of weeks if nobody works any magic.
I am getting the following rates, per card, using driver 344.16, with +200gpu & +200mem
XCN 8mh
XMR 440h
X13 4.8mh
Scrypt Jane 6KH
Not tried BBR yet cause can't get 970's to work with Kopiemtu
System is drawing aprox 380w (not inc display) at wall, AMD quad core cpu so the 970's are using aprox 100w per card.
A month on and I love my 970GTX's, tempted to get more! 380w total including system mean more than 100w per card, unless your system without gpu consume 180w alone, also cpu should be at idle when you mine, i'm missing something? I have never had my cup idle while using ccminer. Am I missing something on how to do that? Now it is not at at 80% or anything but definitely not idle. |
|
|
|
Thanks mumus. That did it. I didn't see that post. |
|
|
|
|
@ djm
I get an error after running the bat.
The application was unbable to start correctly (0xc000007b). Click OK to close the application.
I am running Windows 7 64bit and installed the 14.9 driver. using a 280x and 270x.
|
|
|
|
i'm running sgminer3s without any problems for days continuously on my linux rig, no problem with pool. troubles are mainly with sgminer3s.exe for windows. please check OP for sgminer3s.exe native build which was added this morning
All the .cl files was missing. I just added them from the last release. |
|
|
|
Cards are factory OC but I have not done anything else beyond that.
risers? having trouble getting consistent work from pools. hangs for several minutes. using cgwatcher to restart the miner. My three 750ti's are on risers and my 970 is in mobo. I am using Windows 7 64bit on Nvidia driver 344.11 I have had no issues at all on the Nvidia cards but I do have my rig with the AMD cards running on CGWatcher and restarting the miners every hour because they freeze up on that one. Again no issues at all on my rig with just the Nvidia cards. Have you tried another pool? I am on Block Factory and running smooth. EDIT: Let me change that " running smooth". Rig runs fine but it does slow it down a little. I can't watch videos as they are running slow motion. Besides that no issues. |
|
|
|
|
Show Posts
