 Show Posts
|
|
Pages: [1]
|
It's on the opening post: https://discord.gg/Pbc6uuRLots of people in there talking about issues with rewards over the past few days. |
|
|
|
Can you comment on the voltage setting? I don't see it on the overview page. Thanks! |
|
|
|
|
The best thing about this firmware for me is the fact that my miner runs despite the front fan sensor being faulty. Previously, it would shut down because the fan is not sending the correct signal to the control board. Now it runs and ignores that (which is perfect). The fan works 100%, speeds up, slows down, but doesn't send it's speed to the controller. I don't have to replace this expensive $80 fan any more now, it just runs.
|
|
|
|
Fantastic job Blissz! Running at stock frequency on lowest voltage... very stable. I'll post current draw as shown on my UPS shortly!
*EDIT* 1.3kW reported at the UPS = 650W each! Noice!
You're welcome! Yep that's a nice decrease from 800W  In total on 2x L3+ and 2x D3 I am using 2700W instead of 4000W - a saving of 1300W! At our local rates of around $0.15 / kWh that's $140 a month savings on electricity... very happy! |
|
|
|
|
Fantastic job Blissz! Running at stock frequency on lowest voltage... very stable. I'll post current draw as shown on my UPS shortly!
*EDIT* 1.3kW reported at the UPS = 650W each! Noice!
|
|
|
|
Can I just say that this is the best thing to happen to the D3 since the D3 itself? @Blissz any chance of an L3+ mod? 1.5% of L3+ profits will be more, just saying  |
|
|
|
And then this..... Tell me how they say webforms caused the issues, yet they come right back and say send in a webform.. Oh come on scrap, you were defending them not too long ago.  So you base my experience on number of posts. Tell us why your opinion is worth much - and no, you can't use post count. |
|
|
|
|
I would like to see a target chip temperature for fan control.
e.g. If I set the target chip temperature to 70 C and the hottest chip reaches 70C, the fan speeds up until it's down to 69 or 68 and then slows down again to keep the chip temperature within a certain range instead of just guessing what the best fan speed range is to maintain a certain temperature.
|
|
|
|
This has probably been asked before, but are you perhaps considering a similar firmware for L3+?  |
|
|
|
|
I'm calling it fake based on probabilities.
A company NOBODY has heard of produces 3 of the most powerful miners anyone has produced by far and at a cost way cheaper than anything else out there... and they have been doing R&D on 3 units quietly in the background and suddenly all 3 are out there for sale
Anyway, anyone willing to part with their $4k is welcome, just make sure you come back here to say I should have listened.
|
|
|
|
|
Are you guys not listening lol.
It's FAKE.
The domain was only registered a month ago yet they have 3 models for sale?
F-A-K-E
|
|
|
|
|
Has anyone actually been able to get the windows wallet to work?
I've mined 0.3 so far into my windows wallet address but can't do anything with it since I can't get it to connect. I've tried multiple computers - all say 'there are 0 active connections to the bitconnect network'.
I've tried turning firewall off.
My connections are straight forward.
I've also opened a ticket with their support team without any response.
This is either a scam or a seriously poor project.
|
|
|
|
If it looks too good to be true, it probably is... https://xtract-tech.io/xt-l1-litecoin-miner/Domain Name: XTRACT-TECH.IO
Registry Domain ID: D503300000045429370-LRMS
Registrar WHOIS Server: whois.namecheap.com
Registrar URL: www.namecheap.com
Updated Date: 2017-10-18T20:50:44Z
Creation Date: [b]2017-09-14[/b]T20:06:46Z
Registry Expiry Date: 2018-09-14T20:06:46Z
Registrar Registration Expiration Date:
Registrar: NameCheap, Inc
Registrar IANA ID: 1068
Registrar Abuse Contact Email: abuse@namecheap.com
Registrar Abuse Contact Phone: +1.6613102107
Reseller:
Domain Status: clientTransferProhibited https://icann.org/epp#clientTransferProhibited
Domain Status: serverTransferProhibited https://icann.org/epp#serverTransferProhibited
Name Server: PDNS1.REGISTRAR-SERVERS.COM
Name Server: PDNS2.REGISTRAR-SERVERS.COM
DNSSEC: signedDelegation |
|
|
|
I have an Electron Cash wallet (2Fa enabled) and tried to transfer my BCC to another wallet but received an error about the network not supporting the transaction. I posted a bug on github but just realised that Electron Cash links you to Electrum's github page to report issues... I know it's based on Electrum but is that right? Anyway, I'd read that some people suggested switching 2Fa off but I can't seem to do that. I tried rebuilding from seed and opted for no 2Fa yet it still says [2Fa] at the top. The money I tried to transfer out is sitting in 'unconfirmed' and it's been more than 24 hours like that. I had a similar issue a couple of days ago but after about 12 hours it reverted back to normal. Has anyone had similar issues and any idea how I get my money out?   |
|
|
|
|
OK, so this has been resolved. The issue is that I did not have .06629 balance - the amount showing as my balance has been rounded up. If you hover the mouse over the amount, you will see the full amount - in my case it was .06628xxx.
Seriously...
Anyway, I had to do that. And to others, no, there are no fees - I can withdraw all. See 'Our fee' in the image. it's 0.
|
|
|
|
Anyone tried them? I heard somewhere about their BCH price being pretty comparatively low so I thought I'd see about getting myself some BCH. So I pushed a small amount of BTC to them (0.066 or so) and tried to transact but found that they don't actually allow you to purchase BCH on any of their pairs. So long story short, I tried to withdraw my BTC and got this:  Naturally I sent them a support request:  This was their response:  And THAT, people, is why the world wants crypto regulated. |
|
|
|
|
