Mining sa asia1.ethermine.org, gamit ng ethos, at Windows.  Kada 45 - 50 hours, ang rigs ko ay hihinto sa kaka mining.  Makikita ito sa ethermine.org, na sabay sila huminto.  Pero kada check ko sa Ethos, naka hang, at wala ng makita sa screen.  Kaya hindi ko alam kung anong nangyari.  Hindi ko pa napansin kung anong nangyari sa Windows machine.  Nakakalimutan kong tingnan. 

Ilang beses na ito naulit, at not sure kung issue ba ang asia1.ethermine.org?  O PLDT ba? 

Pwede paki-confirm kung meron sa inyo naka experience ng ganung scenario?

Hi Guys, want to ask, if sending eth to eth wallet in coins.ph, how much eth or fees is charged?  When cash out to bank, e.g, Commercial Bank, how much Peso or eth, or btc is charged?

Thanks

Exactly sa Ethermine.org.  Hindi ba malaki ang charges, o lugi sa exchange rate pag nagconvert eth to php sa coins.ph?  In general, 1k peso max is acceptable, meaning, lugi sa conversion, pati charges ni coins.ph, ok na sa akin.  Kasi 60 usd to withdraw sa Kraken, to bank, mataas.  

@Torbeks, @VitKoyn, @xYakult, @crairezx20, thanks.  Very helpful ang input niyo.

I believe there's the most cost effective way, and there's the easiest way.  I opened a kraken account, but saw to withdraw via wire transfer to bank outside US, fee is 60 USD.  I feel it's steep.

I want to know whether anyone has tried this route?

What other options do we have to convert our eth to usd or peso, into our bank account in the Philippines?

I was instructed to run the command from ethos distro irc channel.  It worked.  It got my power consumption down somewhat.  Looking for more if possible, or until someone tells me it's enough already

anyone?

Hi all.  I need some help lowering my rig utilization.  I've been trying all sorts of combination.  But I can't lower it significantly. 

I have a the following config

1st PSU on the mining rig
HP PSU Platinum DPS-1200FB on breakout board on 220V   (1040W)
Asrock H110 Pro BTC+
Core i3-7100
4 GB
7 Sapphire Nitro+ RX580, 8 GB Hynix
memory: 2200
core: 1130
vlt: 840
pwr: 2

2nd PSU on the same rig (865W)
HP PSU Platinum DPS-1200FB on breakout board on 220V
3 Sapphire Nitro+ RX580, 8 GB Hynix
3 Gigabyte Aorus RX580, 8 GB Hynix
memory: 2200
core: 1167
vlt: 850
pwr: 2

I somewhat feel there are still improvements that can be done.  All Nitro+ cards mining at 30.2 and all Aorus cards mining at 30.5.  I already run "source <(curl -s http://paste.ethosdistro.com/raw/qeticiribi" to get the first psu down to 1040W, otherwise, it will be 1130W or so.  Please help.

Hi, I hope someone is still watching this thread.  I've individually modded my cards Sapphire Nitro+, Sapphire Pulse, Gigabyte Gaming, all RX580 8 GB.  Each can achieve at least 30 mhs.  I'm using Asrock H110 BTC Pro+.  My Nitro+ and Pulse can be detected.  When I plug in Gigabyte Gaming, it doesn't get recognized.  It did once, but when I reboot, no matter what slot I connect it to, it no longer gets detected.  I added another Nitro+ and still gets detected.  I also changed the newly added Nitro+ card's slot, just to make sure, it still gets detected as the 3rd.  But no matter what slot I put in Gigabyte Gaming, not detected.  I have isolated the card on it's own, and risers.  It's working independently.

Can anyone share how to get this board past 3 GPU in ethos?

I have 1 mix mining 6 amd and 5 Nvidia gtx in windows.  Now, I want another rig all Rx 580, in ethos. I cannot past 2 gpus. The 3rd gpu is not being detected. Shall onboard video be disabled? I already connected 2 molex connectors to the motherboard.  I once got to boot into ethos with 3 cards recognized. I adjusted the config and reboot the rig, it doesn't recognize the 3rd card anymore. All 3 cards are rx580. Should there be any sequence? I started with 1 card in gpu0, detected, mining, and added another to the slot nearest cpu? I added another 3rd, very near towards the other side of the board. But no matter how I move the 3rd card on different slots, only 2 are detected.  Please help.

Used August AMD released blockchain drivers fine until this morning, when I woke up, Claymore still mining, but my undervolt on RX580s was rendered useless.  I'm mining at "TOP" wattage.  I've uninstalled using DDUninstaller, reinstalled the blockchain drivers again, without installing AMD settings, fearing that Wattman may conflict with Claymore cvddc, mvddc.  Up to now, still doesn't undervolt.  It was still working very well last night.  What should I do?

I have 6 RX 580 and 5 GTX 1070, using AMD Radeon Beta Blockchain driver. 

I have AB installed.  Forgot which version.

Used to be, I have Claymore undervolt AMDs and AB powerlimit Nvidias.  Using Claymore to undervolt AMDs since powerlimit in RXs greyed out.  Which works out fine for me.

I restarted my rig today, and it informed me that AB has some update.  It didn't ask to install, instead, I thought it was a simple notification.  After which, AB can adjust powerlimit for RX already today.  My power usage shoot up, and my claymore undervolt settings no longer working. 

I am thinking uninstall AB, and reinstall old version, 4.3.0?  So as RX powerlimit stays greyed out?  And again use Claymore to undervolt?  Will this work?

Hi.  Need some clarifications.  I heard when using RX cards, to achieve high hashrate, Bios mod is essential.  I already did, and am hashing about 30 MH/s on my Gigabyte Aorus RX 580s Hynix 8 GB.  My problem is, the bios mod I flashed resulted to very high power consumption.  A few questions below:

1. Is it natural go get a higher power consumption after bios mod increasing hashrate?
2. Do you guys undervolt directly onto bios mod?  Or is it only the hashrate everyone is after?
3. Can you undervolt as effectively in Claymore as in bios mod?
4. What are the things to tackle to undervolt in Claymore?  -mvddc, -cvddc?  Does -cclock affect power consumption?

Thanks

What are the types of GPU you are using? All AMD? or mix with Nvidia? If there is a mix, follow @Vann's advice, the slots have pairings. 1st and second slot has to be the same brand (E. G. BOTH AMD), , third and FOURTH can be another brand, last can stand alone. This advice solved all my problems.

Thanks MATHReX, Branko,

I'll try.

Hi.  I use ATIwinflash 2.77 on Windows 10, 64-bit Professional.  It's been a pain using the app since there are times, I can backup original bios, there are times, it won't.  I'll give out errors (Error reading from ROM).  At times, rebooting will work, and allow it to save to file.  The same intermittent pattern is observed when flashing bios onto card, where on occasion, it will flash, at times, it won't.  I don't know exactly how to fix this, all I do is I reboot, and try again.  At times, closing Sapphire Trixx will work, sometimes, it won't.

Anyone experiencing the same intermittent behavior?  How did you fix this?

I have 5 RX 580s, and I have 5 GTX 1070s.  All mining at the same time.  As of the moment, my ETH Hashrate is 307 MH/s.  Total power is 1550 Watts from wall.  Is this acceptable already?

My Celeron 3950, motherboard, and 8 GB memory eats up 50 Watts.  My 5 GTX 1070s while mining, eats up 625 watts.  My 5 RX 580s while mining, eats up 893 watts.  

I undervolt RX via Claymore.  -powerlim -30, -30, -30, -20, -30. -30 for Gigabyte Aorus RX 580s, and -20 on Sapphire Nitro+ RX 580s.  Anyone getting more efficient power than me?  Hope you can share some tips.

All measurements from wall.

Does v10 support ETH and ZCash Dual mine?  Under Windows.  Also, I have a mixture of 5 GTX 1070s, and 6 RX 580s.

You know what? For the first time I got all 10 cards on a same rig running. Special thanks to @Vann for pointing out the pcie groupings. Following your advice solved the problem instantly.

Oh, I didn't know I can do that on same machine.  Any particular instruction?  I'm still confused how to identify which gpu is which in the rig.  Where do I base "di" option?

And what is the size of the Virtual memory you are using?  32 GB?  Or does it need to be increased for 13 GPU.

BTW, does it mean this motherboard doesn't require 2 molex inputs if you disable it in the bios?  I had to use a separate PSU just for the motherboard since I'm using server psu with pico board.  Kindly confirm this.