 Show Posts
|
|
Pages: [1]
|
Vega 56 can show 1800-1900 h/s on the cryptonight, which is quite proficient if fan noise does not cause problems
Do u have a screenshot that you can show us?? |
|
|
|
Anyone else having disconnect issues with hashparty io? What is a stable pool to mine etn on?  |
|
|
|
Fresh install of Fall creators update.
Download/unpack AMD drivers.
Shut machine down.
Install 3x Vega cards
Remove network cable
Boot machine and install drivers with no network connection.
Reboot machine
Go into crimson, enable HBC max.
Reboot
Connect ethernet
Begin mining XMR, 3,500h/s for 3x Vega 56x
Grrrrrrr
you don't need HBC turned on and set your pagefile as high as possible. On/off it does not make a difference. System memory is at 16GB and pagefile is at 70GB. What is your hashrate with 2 vegas? Maybe the third vega is causing the issue. |
|
|
|
@ bitfools, are you normal? You don't have to turn us blind to make your point, I almost quoted you but realized it will make the page difficult to read.
not normal, majority here are bots, then minority post on mobile phone, that make me abnormal Please enlighten me on how to spot a bot message? I would seriously like to know.... Thx in advance! |
|
|
|
A .gif is worth a million words!  |
|
|
|
Half way thru movie and need to re-butter popcorn 1sec brb  |
|
|
|
So is it still testnet? how will I know that pool.gold switched to real thing?
When people are happy in this thread!! |
|
|
|
I am very confused about this this whole situation, the only thing im not confused about is what coin my rigs are pointed @ and its definitely not this coin Yet! |
|
|
|
Anyone having any luck mining btg? The site seems to be down but us-east.pool.gold:3044 is accepting my shares at the moment What wallet are you using? |
|
|
|
Anyone having any luck mining btg? |
|
|
|
$624 usd for vega liquid on ebay sold by newegg, how many should I buy?  |
|
|
|
almost vegas are mining ETN?  It was fun while it lasted So it is no longer profitable to mine ETN with vegas? What happens in Vega's, stays in Vega's. Shhh.. Dat's what she said  |
|
|
|
almost vegas are mining ETN? It was fun while it lasted So it is no longer profitable to mine ETN with vegas? |
|
|
|
|
Is this coin still profitable to mine with rx vega 64?
|
|
|
|
Guys, I'm still dropping to 1500 per card (two vega 64s with 16GB RAM) after 20-24 hours. Am forced to restart everything to get back to 1900 per card. Can anyone share their insights as to what I might be missing? I have the cards running on a rig I remote into, so no displays attached at all (not even to the onboard video). Maybe I need dummy HDMI dongles? Thanks for any help.
Someone a few pages back said, if on windows 10 go to system/ advance system settings/advance/settings and select best performance. By default its set to let windows choose whats best for computer. This is what helped my windows 10 1vega 64air, 1vega 64lc, 8gb ram system 3940hs total. |
|
|
|
Guess we need some tool (utility) for reg-modding or this thread will be flooded with regfiles ))
And yes - putting random clock-values to P2-P5 states is not a good idea ))
Sir, you are absolutely correct. I have actually created a simple xls to make it more comfy for myself. Added bits & pieces to make it safe for usage. Maybe you'll get a dedicated program sometime soon  Not sure if it works in OpenOffice, will have a check on this tomorrow. https://mega.nz/#!EKgHDI6S!b4OjeKGATtb6ct19e2MBwPRDpd2TLXCfzqqKdmXnfpU
Please follow the steps as per below: Attention: Please read existing guidelines very carefully how to adequately setup Vega64 BIOS. I don't take any responsibility in hardware fault or system damage(!). Credits for SoftPowerPlayTable go to hellm on Overclock.net for documenting everything. Thanks to rednoW for highlighting this stuff to me Very simple steps to be performed: 1. Enter graphics card you want to adjust 2. Enter desired voltage in mV per P State 3. Enter desired Clocks per State 4. Enter MEM Clock Rate 5. Hit "Generate reg file" 6. Run .reg file 7. Reboot 8. Go to Wattman, reset settings 9. (Some say to put voltage to manual control - for me it works without) 10. ...Mine & Profit  It seems that it needs a password to alter any values??? |
|
|
|
There's one thing I haven't understood yet... These regedit changes are for Vega64 only, or they also improve the Vega56 above the 1850H/s from wattman alone? I'm unsure if I should stop the miner or not to try that out Worst case scenario I end with my wattman problems when one gpu decides to reset to default values, but I wonder if with 64 bios and the same vega 64 values the V56 can also reach stable >1900s I am interested to see if any of your vega 56s will make your system not boot(after registry edit), like it does to some of use unlucky ones with vega 64s. Flashed on Vega 56 and it booted and hashed but crashed after 3 minutes. Flashed on 4 other Vega 64 and they have been running with no issues 1408/1100 900MV softplaymod Thanks, that is good info! What do you think is the issue with our system not booting with certain vega 64s? |
|
|
|
There's one thing I haven't understood yet... These regedit changes are for Vega64 only, or they also improve the Vega56 above the 1850H/s from wattman alone? I'm unsure if I should stop the miner or not to try that out Worst case scenario I end with my wattman problems when one gpu decides to reset to default values, but I wonder if with 64 bios and the same vega 64 values the V56 can also reach stable >1900s I am interested to see if any of your vega 56s will make your system not boot(after registry edit), like it does to some of use unlucky ones with vega 64s. |
|
|
|
Hello guys, building a 6xVega XMR mining rig, need some advice.
Parts:
Asrock H81 Pro BTC R2.0
Intel Celeron G1840 (can't get cheaper CPU)
16GB DDR3 RAM, I already have this
250GB SSD
My problem is Vega 64 and 56 are the same price (600 euros). Should I buy 64s or 56s?
Is there any point in buying a Ryzen CPU instead and have it mine as well?
Thanks in advance.
I wouldn't go with 6 Vega now, to many problems can be. 4 Vega+something else (Nvidia for example) should be fine What kind of problems? See ( https://bitcointalk.org/index.php?topic=2201970.0). In short, it seems we cannot easily enable HBCC on more than 4 cards. I had it working on all 6 at once point, rebooted, never been able to get back. Read the first post, I've tried everything short of nuking Windows entirely. Others are reporting the same issues. What I wouldn't do for some trick to avoid having to disable/enable HBCC on every card after reboot to get 1900+H XMR. Also, regarding the power table mods. OLDComer's mod works on 4/6 Vega64's I have. The same two cards I cannot enable HBCC on also seem to ignore the power table registry settings entirely. Likely a clue there but I am not sure what. I have a similar issue, my setup - 1x vega 64air and 1x vega 64water, windows 10 pro64bit, 4gb ram. With oldcomers mod the water vega works great but with the air windows will not even boot. I have tried them together and separate and I get the same result. Could it be my vega 64air bios?? When I apply Oldcomers mod the air card installed by itself it just ignores the registry values from the mod. |
|
|
|
|
