hi habe Interesse an zwei bis drei ungeladenen Münzen. Woran erkenne ich dass die nicht geladen wurde?

Could you change your mountingholes to 3.18 mm? I have never seen any smaller mountingholes than M2,5 on electric equipment.

We could offer you an individual water cooler with a size of 100x30x15mm (2 x 1/8 "fittings) ~ 40 € each (> 100)
Are you planning to design another backplane for water cooler?
If yes, i have some suggestions: Try to put more boards on one cooler. Use the front and the backside of the watercooler.

2 short examples:
If you use front and back of the watercooler, the cost per board would only be --> 20 €
If you manage to put 4 boards on a 100x70x15 (2x G1/4" fittings) watercooler ~ 50 € (> 100pieces)
the cost per board would decrease even further. --> 12,50€ per Board.
Another idea is to use multiconnectors from watercooling for grafic-cards.
But i think the small extra-chip with the ?40A regulator? will prevent all this.


example:
2xBitburner XX with one watercooler http://www.anfi-tec.de/forenbilder/13.07.11%20Bitburner/Anfi-tec%20Bitburner%20XX%201.JPG
finished blocks http://www.anfi-tec.de/forenbilder/C006/13.08.30%20Bitburner%20Waterblocks.JPG
And of course with less coolers you have to do less tubing.

@cscape
for you the same: If you want to overclock them and expect to much heat, please feel welcome to contact us (anfi-tec) for some watercoolers.

Regards Andre

• what do you think will the 12 chips produce in heat/Power consumption in idle?
• and the same with overclocking?
• how many of these miniboards you plan to put on a backplane/rack?
• what distance is planned for the pci-slots (with watercooling you can pack them much closer together than with aircooling)
• are you planing to sell these miniboards?
• cooling from the backside of the board like the avalonchips?

i am sure that we can't use here one waterblock for two boards like we did with bitburner XX waterblock

If you want to overclock them and expect to much heat, please feel welcome to contact us (anfi-tec) for some watercoolers.
Furthermore for a better packing density.

Apart from all the requests for a refund,
here some other news:

for all these who want to bring their bitburner to maximum OC,
the waterblocks had left our company this morning to Burnin Electronics.



hope you all get your chips

some users asked some questions about the waterblock http://www.burninmining.com/product/bitburner-watercooler-by-anfi-tec/

1. the missing picture, here one of our latest prototype with anodized surface


(picture shows the 100x80x15mm Version)

2. the block does have G1/4" Windings,... so you can use ever fitting like its used in usual pc watercoolings.

3. we prefer G1/4 plug fittings 90° for hose with 10/8mm, so you can connect the blocks direct on the Anfi-Tec 19″ Mounting Plate for 8 Watercooled Bitburners
(maybe burnin will offer these in the shop also)
Important: Use only with stiff tubing.
Connector: Cylindrical G1/4" thread and for 8x1 hoses (as=10mm outer diameter)
we also want to offer burnin some hose for make some "complete watercooling sets".

4. We were forced to design a very simple (low cost) waterblock that can be produced very fast to not let anybody wait.
So we made a smaller version with 100x80x15mm (burnin tested already with this prototype)
anyway we thinking about cooling the whole wide pcb, so we are planing a 108x100x15mm version, this should also be more powerfull in cooling the vrms.


--------------------------------------------------------------------------------------
questions at mountinplates

1. the mountingplates contains the 2 handles

2. you don't need a professional 19" rack to mount them. You can just use a normal shelf or closet what is about 200-300mm deep (depends on the power-suply) and screw it in the front. We will make a photo when we finished the first frontplates for user toolhead.



--------------------------------------------------------------------------------------
furthermore to our waterblocks you need some like this components:

more spoilers from our side:

Anfi-tec 19" frontplate (3HE high) for 8 waterblocks (16 Bitburner XX boards)

backside


Anfi-tec 19" frontplate (3HE high) for 2 powersuplys and a Raspery pi or some other things to mount (4x 5mm holes for e.g. some angle-iron)

backside


---------------------------------------------------------------------------------------------------------------------------

example of some useres order:
3x Anfi-tec 19" frontplate for 8 waterblocks, 1x Anfi-tec 19" frontplate for 2 powersuplys in a Rittal 19" Rack





We will produce the fontplates on demand! So make shure you order them (at Burnins shop) in the first 2 days after the Shop is online. We will do our best to have them ready as soon as possible!

regards
[Anfi-tec] André

and i am the other part of Anfi-tec

like to hear this

are there more projects like the "bitburner XX" ?
"Custom hardware"  the right chanel?

hi all together. I'm new here by a user from the avalon area.

I usually produce waterblocks for computer.
this is my company http://shop.anfi-tec.de/

watercooling made in germany

and maybe someone knows us from another hardware forum:
like:
http://www.overclock.net/t/271025/af-andreoid-finnzwerg-watercool-tinkering-tons-of-pix/560#post_16197344
or
http://hardforum.com/showthread.php?t=1467547&page=100

I just develope a water cooler for "bitburner XX"
the idea is to increase the packing density and to enable problem-free overclocking the boards. questions are of course very welcome.

've heard there are many other BitCoinMiner. so that here is an exciting new area for us.
will now look at a few threads to get a better view on this hardware.


----------------------------------------------------------------------------------------------------

hi alle zusammen.
ich bin neu hier, durch einen user aus dem avalon-bereich.

normalerweise stelle ich wasserkühler für computer her.
das hier ist mein firma http://shop.anfi-tec.de/

watercooling made in germany

und vielleicht kennt uns schon jemand aus einem anderen hardware-forum
http://www.overclock.net/t/271025/af-andreoid-finnzwerg-watercool-tinkering-tons-of-pix/560#post_16197344
or
http://hardforum.com/showthread.php?t=1467547&page=100

ich entwickel grade einen wasserkühler für "bitburner XX"
die idee ist die packungsdichte zu erhöhen und eine problemelose übertaktung der boards zu ermöglichen. fragen sind natürlich sehr wilkommen.

habe gehört es gibt noch viele andere bitcoinminer. so das hier wird ein neuer spannender bereich für uns.
werde jetzt noch ein paar threads angucken.