Show Posts
|
Pages: [1] 2 3 4 5 6 7 »
|
If someone finds a way to decode and re-encode the memory timings for HBM1 it would be of great help nowadays, I've heard comments that you can get a lot of performance out of it as far as kawpow and etchash... The biosmods of these cards were lost in limbo Also here I leave my grain of sand, these are timing that I found by chance in the forum and implanted it in the vbios (they are slow timing) maybe it can be useful for someone https://www109.zippyshare.com/v/my2xJZr0/file.html <------ It has a minimum voltage of 775 mv so there is a large margin for undervolting PD, disclaimer, I am not responsible for the damage caused although the changes are very minimal compared to the original bios, it applies only to the nitro version of sapphire PD2, in case of failure these cards have dual bios, change to the main one and repair the secondary bios with a previously made backup What the hashrate for etchash and kawpow with your bios?
|
|
|
I guess in terms of performance and efficiency the nano is ahead in architecture fiji PD, they released a version for ETC + KASPA for these cards with lolminer
Oh New Release 6 hours ago Added experimental ETC+Kaspa solver for R9 285 / R9 380 (Tonga), RX Fury (Fiji) and RX 460 / 550 (Baffin) GPUs Thank to Notify
|
|
|
Its rare to have people actually mining with the R9 Fury. I remember back in 2015 they were very expensive and had many hardware defects and people either used the slightly less efficient R9 290X or they waited until the Polaris came out in 2016 and the efficiency was pretty much on par. After summer 2016, nobody really used the Fury for mining.
They were popular with gamers and most miners sold their Furys and bought some Polaris cards. So this is why you don't really hear too much discussion about the chipset. I think it was AMDs least produced chipset.
I still mining with R9 NANO. I give some information for someone who have R9 Fury. Not suggestion to buy it now.
|
|
|
PD, in any case if it has the shortened version (the fury with 56 cu sapphire) I can upload the vbios with the modified timing and you will be able to verify that amdmemtweak does not reflect the changes although in mining it behaves differently
I have version 64cu and I can applay timing with amdmemtweak it reflect to some algorithm as Argon2d-nim hash from 360 KH/s to 400 KH/s. But now not time to mine NIM
|
|
|
Does anyone still keep memory strap modded in hexadecimal format or at least biod mod? I have the original straps but I have no way to decode it, there is nothing related to the HBM memories (linux user, amdmemtweak doesn't work there on fiji-HBM architecture)
What the mining result with memory strap modded? amdmemtweak work fine on HiveOS. You can run command with menu "Run Command". example command "amdmemtweak --REF 17000 --RFC 48 --RC 20 --RCDR 6 --RCDW 6 --RCDRA 6 --RCDWA 6 --R2W 6 --W2R 6 --FAW 1" If you have good strap mod command, let me know it, I have 10 Fury NANO
|
|
|
V0.9.6 + Added algorithm 'kaspa' (KAS - Kaspa coin) for CPU/GPU mining, fee 1.00% + Small performance increase on 'heavyhash' algorithm for RDNA2 GPU's + Lower power consumption on 'heavyhash' algorithm for RDNA2 GPU's + Minor bug fixes
Please support fiji
|
|
|
And the another way, suggest to see TONCOIN it time to take profit Algo: Darkcoin Coin: TONCOIN Hashrate: 1020 MH/s Power: 104w Miner: lolminer 1.42
|
|
|
For now, Kowpow is not the Best Profit on R9 NANO I suggest to mine NIMIQ, when difficalty is low. For Check Diff https://metrics.nimiq.cafe/difficulty-growthAlgo: Argon2d(NIM) Coin: NIM Hashrate: 390 kh/s Power: 120w Miner: TeamRedMiner
|
|
|
waiting optimize phi5 for r9 nano
|
|
|
Yes, r9 nano easy to config OC.
|
|
|
Suggest profit on Chukwa v2
Algo: Chukwa v2 Coin: TRTL Miner: Teamredminer v0.7.16b
On mid power Hashrate: 34kh/s Power: 120w
For High power Hashrate: 36Mh/s Power: 141w
For expert miner can use "AMD Memory Tweak XL" config --REF 104 --tRFC 48 --tRC 20 --tRCDR 6 --tRCDW 6 --tRCDRA 6 --tRCDWA 6 --tR2W 6 --tW2R 6 --tFAW 1 Thanks for Discord user: mrdx#0572
Result is On mid power Hashrate: 36kh/s Power: 120w
For High power Hashrate: 40Mh/s Power: 141w
|
|
|
4gb card stopped working today, fix?
Try to restart miner, it should work fine. And check the GitHub, there is new version Team Red Miner v0.7.12 nothing, all my 4gb rig stopped working with eth Used Linux OS, gpu 4gb run smoothly
|
|
|
lyra2REv3 take Profit
|
|
|
What the hashrate for Beam ?
|
|
|
1.05 Thanks for impove Fiji
|
|
|
Update hashrate Beam Hash III
Algo: Beam Hash III(BEAM) Coin: BEAM Hashrate: 20 sol/s Power: 120w Miner: lolMiner 1.04
|
|
|
Update mining with algo Argon2d and Beam Hash III
Algo: Beam Hash III(BEAM) Coin: BEAM Hashrate: 16 sol/s Power: 115w Miner: lolMiner 1.02 (ver 1.03 is not better than 1.02)
-------------------------------------------- Algo: Argon2d(NIM) Coin: NIM Hashrate: 390 kh/s Power: 120w Miner: TeamRedMiner v0.7.7
On power save Hashrate: 288 kh/s Power: 75w
On mid power Hashrate: 390 kh/s Power: 120w
For Free Electric Hashrate: 412 kh/s Power: 145-156w
|
|
|
Fiji - Win 10, Driver AMD 20.5.1 AB is the same OC Ver 1.02 get 16 sol/s ver 1.03 get 11.4 sol/s Cannot find OC setting for increase hashrate on 1.03, ver 1.02 is better for Fiji.
|
|
|
I’ll try to mine Monero within a week and write off the result, it is very interesting to see it in action.
|
|
|
|