 Show Posts
|
|
Pages: [1]
|
|
Hallo zusammen
Ich hab da mal eine kleine Newcomer-Laienfrage....
Ich habe insgesammt 6 Miner - 5 davon sind typengleich.
Nun stellt sich für mich die Frage, was ist effizienter?
Die 5 typengleichen Miner auf einem Worker zusammen laufen zu lassen, oder
für jeden Miner einen eigenen Worker zu verwenden?
Den 6ten Miner kann ich aus kompatibilitäsgründen nicht mit den anderen 5 laufen lassen.
Besten Dank für eure Meinungen.
|
|
|
|
|
Hi
I have a technical qouestion....
CGMiner tells me an average of 115.9Gh/s.
My Dashboard says (after a counter-reset and about 5 minutes of wait) 108.6Gh/s.
Why is this difference?
|
|
|
|
Hi
I have a big problem.
I have 5 miners and all of them work fine IF a let them work one by one...even two together work fine.
BUT.....
If i want to let 3 miners work together, the PSU crashes.
The miners, the hub and the MR-3020 are ALL conected to the same PSU-Molex cable-tree.
The PSU has 550W....
What can be the problem?
Can it be that the PSU is too old even it has NEW 550W?
Pls help me ..... i cann't solve this problem
what is the rating AMPS of PSU 12V rail is it a single one? PSU-Model: pentium iv & pfc model lc6550G version 2.0 MAC DC OUTPUT: Voltage 230V: +3.3V -> 35A +5V -> 40A +12V1 -> 16A Current 4A +12V2 -> 18A -12V -> 0.8A -5V -> 0.5A Frequency 50Hz +5VSB -> 2.0A BLK - > COM GRN - > PS-ON GRY -> PG I made a shortcut betwen the green and black cable to turn the PSU on without motherboard. So 1. Chosse a single rail PSU 2. When board is OC-e it is eating about 9.5 Amps So if i were on your shoes i will connect just two boards to this PSU when i am absolutely sure that each board is connected on a separate 12V rail. Does this explanation clears up a mastery crash;) And do not push it to much magic smoke will come out sooner or later. I am not joking here i am serious So you say that the PSU is too poor to run more then 2 boards at once? Will a new PSU work better and how much power do i need to run all 5 together? Would this one do the job? http://www.coolermaster.com/powersupply/v-series-psu/v1000/Dude, First please excuse me i just saw that it is Avalon2 boards. So i do not know what the board consumption is but i know that it is getting close to Avalon1 And definitely i say that i would not run more than two broads on this PSU. Whatever you do choose a SINGLE rail PSU. Do you know to what rails are the boards connected i guess no.. and so on PS: http://www.coolermaster.com/powersupply/v-series-psu/v1000/Yes it will do and you will have a room for more boards this one is too powerful. My advise is to measure exact board consumption on 12V and choose appropriate one you can save a bug for sure. If this is not an option for you go with 1000W  I just orderd one of these PSU's and in a few hours i will try it out. Hopefully it's gonna do the job. Thank you very much for your help so far. I'll gonna give a feedback when it runs. ;-) It will do the job. Just make sure you use all molex cables. Do not connect more than one miner to a single molex cable even though it has two more connectors in parallel. Unless you ought to This is the best advice here. If you have more miners then Molex then use a ATX 4 pin extender to molex or 4 pin extender and cut the cable off one end. That way you still get 12v but it is not all on the same cable. Even a single one can cause the molex wires to be warm. Well.... I have the things pluged together and everything works just fine and smooth. Two Molex-Cable and three SATA-Cables with Molex-Adapters. Every miner has its own powercable and the cable keeps really cool. My configuration for the miners are: [Frequency] => 1400 [Core Voltage] => 1000 and i get [MHS 5s] => 22.33G [MHS av] => 21.39G I know that i could go up to Frequency 1500 and CoreVoltage 1100, but i get not more hashes. I need just more Watts. Thanks for your help and advise to everybody here. Happy mining |
|
|
|
Hi
I have a big problem.
I have 5 miners and all of them work fine IF a let them work one by one...even two together work fine.
BUT.....
If i want to let 3 miners work together, the PSU crashes.
The miners, the hub and the MR-3020 are ALL conected to the same PSU-Molex cable-tree.
The PSU has 550W....
What can be the problem?
Can it be that the PSU is too old even it has NEW 550W?
Pls help me ..... i cann't solve this problem
what is the rating AMPS of PSU 12V rail is it a single one? PSU-Model: pentium iv & pfc model lc6550G version 2.0 MAC DC OUTPUT: Voltage 230V: +3.3V -> 35A +5V -> 40A +12V1 -> 16A Current 4A +12V2 -> 18A -12V -> 0.8A -5V -> 0.5A Frequency 50Hz +5VSB -> 2.0A BLK - > COM GRN - > PS-ON GRY -> PG I made a shortcut betwen the green and black cable to turn the PSU on without motherboard. So 1. Chosse a single rail PSU 2. When board is OC-e it is eating about 9.5 Amps So if i were on your shoes i will connect just two boards to this PSU when i am absolutely sure that each board is connected on a separate 12V rail. Does this explanation clears up a mastery crash;) And do not push it to much magic smoke will come out sooner or later. I am not joking here i am serious So you say that the PSU is too poor to run more then 2 boards at once? Will a new PSU work better and how much power do i need to run all 5 together? Would this one do the job? http://www.coolermaster.com/powersupply/v-series-psu/v1000/Dude, First please excuse me i just saw that it is Avalon2 boards. So i do not know what the board consumption is but i know that it is getting close to Avalon1 And definitely i say that i would not run more than two broads on this PSU. Whatever you do choose a SINGLE rail PSU. Do you know to what rails are the boards connected i guess no.. and so on PS: http://www.coolermaster.com/powersupply/v-series-psu/v1000/Yes it will do and you will have a room for more boards this one is too powerful. My advise is to measure exact board consumption on 12V and choose appropriate one you can save a bug for sure. If this is not an option for you go with 1000W I just orderd one of these PSU's and in a few hours i will try it out. Hopefully it's gonna do the job. Thank you very much for your help so far. I'll gonna give a feedback when it runs. ;-) |
|
|
|
Hi
I have a big problem.
I have 5 miners and all of them work fine IF a let them work one by one...even two together work fine.
BUT.....
If i want to let 3 miners work together, the PSU crashes.
The miners, the hub and the MR-3020 are ALL conected to the same PSU-Molex cable-tree.
The PSU has 550W....
What can be the problem?
Can it be that the PSU is too old even it has NEW 550W?
Pls help me ..... i cann't solve this problem
what is the rating AMPS of PSU 12V rail is it a single one? PSU-Model: pentium iv & pfc model lc6550G version 2.0 MAC DC OUTPUT: Voltage 230V: +3.3V -> 35A +5V -> 40A +12V1 -> 16A Current 4A +12V2 -> 18A -12V -> 0.8A -5V -> 0.5A Frequency 50Hz +5VSB -> 2.0A BLK - > COM GRN - > PS-ON GRY -> PG I made a shortcut betwen the green and black cable to turn the PSU on without motherboard. So 1. Chosse a single rail PSU 2. When board is OC-e it is eating about 9.5 Amps So if i were on your shoes i will connect just two boards to this PSU when i am absolutely sure that each board is connected on a separate 12V rail. Does this explanation clears up a mastery crash;) And do not push it to much magic smoke will come out sooner or later. I am not joking here i am serious So you say that the PSU is too poor to run more then 2 boards at once? Will a new PSU work better and how much power do i need to run all 5 together? Would this one do the job? http://www.coolermaster.com/powersupply/v-series-psu/v1000/ |
|
|
|
Hi
I have a big problem.
I have 5 miners and all of them work fine IF a let them work one by one...even two together work fine.
BUT.....
If i want to let 3 miners work together, the PSU crashes.
The miners, the hub and the MR-3020 are ALL conected to the same PSU-Molex cable-tree.
The PSU has 550W....
What can be the problem?
Can it be that the PSU is too old even it has NEW 550W?
Pls help me ..... i cann't solve this problem
what is the rating AMPS of PSU 12V rail is it a single one? PSU-Model: pentium iv & pfc model lc6550G version 2.0 Vac~ INPUT: Voltage -> 230V Current -> 4A Frequency -> 50Hz Vdc MAX DC OUTPUT: +3.3V -> 35A +5V -> 40A +12V1 -> 16A +12V2 -> 18A -12V -> 0.8A -5V -> 0.5A +5VSB -> 2.0A BLK - > COM GRN - > PS-ON GRY -> PG I made a shortcut betwen the green and black cable to turn the PSU on without motherboard. |
|
|
|
|
Hi
I have a big problem.
I have 5 miners and all of them work fine IF a let them work one by one...even two together work fine.
BUT.....
If i want to let 3 miners work together, the PSU crashes.
The miners, the hub and the MR-3020 are ALL conected to the same PSU-Molex cable-tree.
The PSU has 550W....
What can be the problem?
Can it be that the PSU is too old even it has NEW 550W?
Pls help me ..... i cann't solve this problem
|
|
|
|
|
So i have to power the hub AND the MR with a molex conector from the same PSU as the HEX is powerd?
|
|
|
|
|
I have still the problem that 1 Miner over powerd USB-Hub works
and if i plugin the second Miner my PSU crashes.
Is there a problem with the USB-Hub Power? If have 4 Amps powersupply on the Hub.
BTW....
I use a TL-MR3020
Thanks for help
|
|
|
|
|
Hi
Is there a possibility to add Hex-Miners from Technobit.eu?
I have 5 boards and wanted to use MultiMiner but it doesn't work.
Thanks a lot
|
|
|
|
|
I have a problem with the HEX16A2 Miners.....
I have two of them and with Win7 they work just fine.
With the Pi they work as well but only if i connect one of there own.
If i connect them both over a powered USB-Hub, they force a crash of the
Power-Source and i have to reboot everything.
Can anybody help me pls?
|
|
|
|
|
Thank you...
Problem solved
|
|
|
|
|
I am new at BTC Guild and get no payouts since 3 blocks.
Is this normal from time to time or is there any problem around?
|
|
|
|
ERsobt9djJY8QcoowuH8CgBaaCNmE771fQ thx  |
|
|
|
Hallo SpAcEDeViL Ich bin sehr an deinem Raspberry interessiert! Ich bekomme demnächst mehrere 24 GH/s HEX16A2 Miners geliefert und würde diese gerne mit deinem Raspberry betreiben. Kannst du dies gleich so konfigurieren da ich von Linux praktisch nichts verstehe? Käme natürlich für die Umstände auf die du damit hast. gerne auch per PM |
|
|
|
|
