Hi all,
I'm offering to auction off a power supply (New, never used) Escrow service is preferred otherwise you pay first. Auction ends on August 11th. Starting bid 0.001 BTC. Thanks for your consideration.
Photo:
https://ibb.co/bRWbwKHere are the specifications quoted from Amitylabs:
High Efficiency 2450 Watt Server PSU for Antminer S9 / T9 / D3 / L3+ / S7 with Ready-to-Use Wiring (200-240V only)
No more flimsy breakout boards! No more melted wiring! We are experienced bitcoin miners/engineers who offer you power systems that work well in actual use:
Reliability: Our wiring and PSU choices have proved themselves in 24/7/365 harsh condition operations at 100% duty cycle.
Ease of use: Just plug it and turn it on!
Quality: Everything is heavy-duty, high-temperature, above-rating, and fully insulated!
Value: When you add it all up, we come ahead of any breakout board (and way ahead of Bitmain's own power supplies).
Load Specifications:
One Antminer T9 / S9 / D3 / L3+ / S7 / A741 or equivalent high-power
For powering L3+, we also provide the more cost-efficient AMP2450L2 PSU capable of powering x2 L3+ at the same time
You can power legacy miners (R4/A6/SP20...etc) with this PSU - but we have models specifically designed for these jobs (see our other listings)
Power Supply Specifications:
2450 Watt HP server PSU
By running at 50% load with one S7/S9, this PSU achieves platinum 94% efficiency (full load efficiency is 92%)
220V AC (do not damage your home wiring mining on 110V !!!)
7ft heavy-duty C20 power cord is included/integrated
Please specify if you need another plug type (e.g. NEMA 6-15, NEMA 6-20, C13...etc)
Wiring Specifications:
Ten (10x) 16 AWG braided copper 6-pin PCI-E Molex connectors (each rated to 240 Watt / 20 Amps with 80 degrees C insulation)
28-inch long DC power bus made of heavy-gauge flexible braided copper-silicone cable (each rated 960 Watt / 80 Amp with 200 degrees C insulation)
Wiring soldered to the power terminals (minimizes electrical and thermal resistance)
All energized contacts fully insulated with high-strength dielectric epoxy, protected against wear, tear, and heat
PCI-e connector layout optimized for S9 / S7 / L3+, with dedicated connector for controller
Technical Notes:
We solder the conductors to the power terminals, providing for absolutely minimal resistance and optimal heat conduction/dissipation. The solid contact also protects against accidental disconnects, contact sparks, and interface oxidation.
We insulate every hot point with hard electrical epoxy and heavy-duty shrink wrap to prevent accidental shorts and increase hardiness.
We use proper wiring gauge and insulation:
PCI-e insulation is rated to 80 degrees Celsius, and has FT1/WV-1 flame exposure rating
16 AWG PCI-e wiring is optimal given the rating of the 6-pin connectors on your miner (240 Watt per terminal).
Thicker wiring (e.g. 14 or 12 AWG) cannot be reliably crimped to the pin, resulting in local overheating and burnout.
Three 16AWG wires have higher current rating than the 2x 14AWG "hack job" wiring you sometimes see. Bigger is not always better!
We use quality PCI-e connectors with proper crimping:
The weakest part of the PCI-e power link is the pin boot where the wiring is crimped. This is where overheating and burnout starts.
Our PCI-e wiring is custom-made by a leading power cable manufacturer, and is specced for durability.
The connector material has high temperature rating, the pins are correctly sized, and again - the crimp is done optimally.
Our PSUs ready to plug and go. You will not waste your time screwing around with DIN terminals or spade connectors.
Show Posts
