Show Posts
|
Pages: [1]
|
disini ada yang pernah begitu VGA nya ? kipas saya satunya mati/hidup dalam 3-4 detik. cara perbaikinnya gmn ?
terima kasih
|
|
|
Have you tried to set your paging file to 32gb or 64gb? It might be the reasons why your claymore couldn't run properly and you must use some tools to monitor the GPU temps and maybe your cards reach the higher temp that is why it keeps rebooting.
i sett my paging file to 32800 sometimes . i will try 64gb my card not higher temp. 53 only
|
|
|
a lot of possible cause, might be a clock issue, overheat, risers, Power supplies, etc
Are your GPU's modded?
Start with a default command lines and default clocks excluding those above
check also your miner logs and windows logs thru event viewer
you may get a hint what would be the cause
in windows type eventvwr\windows Logs\Application
Yes, My gpu is modded im check windows logs i found some errors there from System The computer has rebooted from a bugcheck. The bugcheck was: 0x000000ea (0xffff90854aa3f080, 0x0000000000000000, 0x0000000000000000, 0x0000000000000000). A dump was saved in: C:\Windows\MEMORY.DMP. Report Id: 585eea90-3d66-4476-9908-2e491f4e08f6. The previous system shutdown at 17:48:19 on 10/08/2018 was unexpected.
|
|
|
Hello, i am running claymore in few hours. and sometimes my windows look restarting with unknown reason Mobo ASROCK B250 gaming k4 Memory RAM PC HyperX Fury DDR4 8GB INTEL PROCESSOR G4400 BOX LGA1151 SSD 120 PSU CORSAIR RMX 1000W GOLD Sapphire RX 580 nitro+ special edition x 6
can you help me what's wrong ? and here is my claymore command setx GPU_FORCE_64BIT_PTR 0 setx GPU_MAX_HEAP_SIZE 100 setx GPU_USE_SYNC_OBJECTS 1 setx GPU_MAX_ALLOC_PERCENT 100 setx GPU_SINGLE_ALLOC_PERCENT 100
EthDcrMiner64.exe -epool ssl://asia1.ethermine.org:5555 -ewal wallet.worker -epsw x -mode 1 -etha 0 -cclock 1150,1150,1150,1150,1150,1155 -cvddc 880,900,890,880,880,880 -mclock 2000,2000,2000,2000,2000,2000 -mvddc 880,905,895,885,875,880 -tt 60 -fanmin 65 -fanmax 80 -platform 1 -eres 3 -tstop 80 -tstart 50 -dcri 8,14,14,14,14,14
|
|
|
you will test your GPU0 config values near stock values. i think increase mvddc value to over 900-950 this will be stops stucking
in Claymore command right ? how about cvddc ? should i need to increase ? No, i connected with HDMI dummy too. You sure your claymore running over 24hours x 7 days, nonstop or no restarting ?
|
|
|
you will test your GPU0 config values near stock values. i think increase mvddc value to over 900-950 this will be stops stucking
in Claymore command right ? how about cvddc ? should i need to increase ?
|
|
|
i don't understand to check it. can i contact you to help me check it ? im still new in mining i will give you my teamviewer ID PASS
thankyou before
No need a remote assistant to learn it, you can find a bunch HWInfo guide and the GPU memory errors details at Google. And you can download this program from this site https://www.hwinfo.com/download.php![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fprnt.sc%2Fkgk7vq&t=663&c=Ar9jVXWCUG6wiw) there all GPU with 0 error. now im trying with lower OC update the result soon
|
|
|
I don't know which GPU you got. But I am assuming its either an RX 470 8GB or an RX 470 8GB.
Your speed is pretty high and I am assuming you are running into stability issues with certain GPUs, like the ones that crashed.
Lower your clocks and increase your voltage a little and see if the problem goes away.
I using SAPPHIRE RX580 nitro+ Special Edition 8GB Yeah actually, it seems like all of your GPUs are overclocked too much. Toning down the OC setting would really do a lot to help you with stability, as well as with the lifespan of your cards. As a guide, you are currently doing 31.4 MH/s per GPU. Toning them dow to 31.0-31.1 MH/s flat could be a good target to increase stability. ETH: 08/09/18-15:46:38 - New job from asia1.ethermine.org:5555 ETH - Total Speed: 184.072 Mh/s, Total Shares: 5, Rejected: 0, Time: 00:01 ETH: GPU0 30.683 Mh/s, GPU1 30.680 Mh/s, GPU2 30.651 Mh/s, GPU3 30.652 Mh/s, GPU4 30.710 Mh/s, GPU5 30.697 Mh/sGPU0 t=49C fan=79%, GPU1 t=52C fan=76%, GPU2 t=48C fan=77%, GPU3 t=52C fan=77%, GPU4 t=52C fan=78%, GPU5 t=52C fan=77%ETH: 08/09/18-15:46:54 - SHARE FOUND - (GPU 5) ETH: Share accepted (15 ms)!ETH: 08/09/18-15:46:54 - New job from asia1.ethermine.org:5555 ETH - Total Speed: 184.343 Mh/s, Total Shares: 6, Rejected: 0, Time: 00:01 ETH: GPU0 30.724 Mh/s, GPU1 30.736 Mh/s, GPU2 30.721 Mh/s, GPU3 30.722 Mh/s, GPU4 30.724 Mh/s, GPU5 30.717 Mh/sETH: 08/09/18-15:47:10 - SHARE FOUND - (GPU 0) ETH: Share accepted (16 ms)! ETH: 08/09/18-15:47:10 - SHARE FOUND - (GPU 0) ETH: Share accepted (16 ms)!GPU0 t=49C fan=78%, GPU1 t=52C fan=77%, GPU2 t=48C fan=77%, GPU3 t=52C fan=77%, GPU4 t=53C fan=77%, GPU5 t=53C fan=77%
thank man before i will try this now. and update result soon
|
|
|
Did you check GPU memory errors at HWInfo ? If you found any errors reported, it looks like your GPU 0 is overclocked too much.
You should try lowering the OC settings or reset the GPU 0 to default clock settings.
i don't understand to check it. can i contact you to help me check it ? im still new in mining i will give you my teamviewer ID PASS thankyou before
|
|
|
I don't know which GPU you got. But I am assuming its either an RX 470 8GB or an RX 470 8GB.
Your speed is pretty high and I am assuming you are running into stability issues with certain GPUs, like the ones that crashed.
Lower your clocks and increase your voltage a little and see if the problem goes away.
I using SAPPHIRE RX580 nitro+ Special Edition 8GB
|
|
|
anyone know what happen ? my Claymore 2 times restarting like this, and my Claymore can't run time over 24x7, even 24hours ony I using SAPPHIRE RX580 nitro+ Special Edition 8GB
07:21:02:636 8b8 ETH - Total Speed: 157.359 Mh/s, Total Shares: 121, Rejected: 0, Time: 00:43 07:21:02:636 8b8 ETH: GPU0 0.000 Mh/s, GPU1 31.470 Mh/s, GPU2 31.441 Mh/s, GPU3 31.477 Mh/s, GPU4 31.483 Mh/s, GPU5 31.488 Mh/s 07:21:02:777 1898 em hbt: 16, fm hbt: 16, 07:21:02:777 1898 watchdog - thread 0 (gpu0), hb time 6043807:21:02:777 1898 WATCHDOG: GPU 0 hangs in OpenCL call, exit07:21:02:777 1898 watchdog - thread 1 (gpu0), hb time 6012507:21:02:777 1898 WATCHDOG: GPU 0 hangs in OpenCL call, exit07:21:02:777 1898 watchdog - thread 2 (gpu1), hb time 141 07:21:02:777 1898 watchdog - thread 3 (gpu1), hb time 141 07:21:02:777 1898 watchdog - thread 4 (gpu2), hb time 141 07:21:02:777 1898 watchdog - thread 5 (gpu2), hb time 141 07:21:02:777 1898 watchdog - thread 6 (gpu3), hb time 141 07:21:02:777 1898 watchdog - thread 7 (gpu3), hb time 141 07:21:02:777 1898 watchdog - thread 8 (gpu4), hb time 141 07:21:02:777 1898 watchdog - thread 9 (gpu4), hb time 141 07:21:02:777 1898 watchdog - thread 10 (gpu5), hb time 141 07:21:02:777 1898 watchdog - thread 11 (gpu5), hb time 141 07:21:02:777 1a88 GPU 0 temp = 36, old fan speed = 77, new fan speed = 65 07:21:02:792 1a88 GPU 1 temp = 51, old fan speed = 79, new fan speed = 65 07:21:02:824 1a88 GPU 2 temp = 50, old fan speed = 79, new fan speed = 65 07:21:02:855 1a88 GPU 3 temp = 48, old fan speed = 79, new fan speed = 65 07:21:02:886 1a88 GPU 4 temp = 49, old fan speed = 79, new fan speed = 65 07:21:02:917 1a88 GPU 5 temp = 49, old fan speed = 78, new fan speed = 65 07:21:03:058 1a88 Quit, please wait... 07:21:10:041 1898 Restarting OK, exit... here is my command EthDcrMiner64.exe -epool ssl://asia1.ethermine.org:5555 -ewal waller.worker -epsw x -mode 1 -etha 0 -cclock 1200,1220,1220,1225,1220,1225 -cvddc 880,900,890,880,880,880 -mclock 2120,2200,2200,2200,2200,2200 -mvddc 880,905,895,885,875,880 -tt 60 -fanmin 65 -fanmax 80 -platform 1 -eres 3 -tstop 80 -tstart 50 -dcri 8,14,14,14,14,14
|
|
|
there is no point fo having 1250 on core, ETH algo gains very little on core OC
okay, i understand thanks
|
|
|
-cclock 1170 -mclock 2125
-cvddc 900 -mvddc 910
try this, did you mod your cards ?
yes i have mod the bios. i will try it now with your command thanks
|
|
|
maybe you overclock to much and you get because of that invalid shares
can you recommend me to update for claymore command ? thanks
|
|
|
anyone know best command for claymore ? get 184mhs hashrate reported and average hashrate 6hours under 160mhs i have 6 gpu sapphire RX 580 nitro+ special edition this is my command setx GPU_FORCE_64BIT_PTR 0 setx GPU_MAX_HEAP_SIZE 100 setx GPU_USE_SYNC_OBJECTS 1 setx GPU_MAX_ALLOC_PERCENT 100 setx GPU_SINGLE_ALLOC_PERCENT 100
EthDcrMiner64.exe -epool asia1.ethermine.org:4444 -ewal ADDRESS.WORKER -epsw x -mode 1 -etha 0 -eres 2 -cclock 1230 -mclock 2150 -cvddc 900 -mvddc 910 -tstop 80 -fanmin 65 -fanmax 80
|
|
|
|