 Show Posts
|
|
Pages: [1]
|
|
Salut à tous, j'aimerai me lancer sur le minage mais j'ai des lacunes sur le comment faire, j'ai récupérer un Asic A3 Blake2b et j'essaie de miner du SiaClassic, bon c'est pas l'algorithme le plus répandu mais c'est juste pour débuter.
Des conseils pour bien commencer, quel pool miner, et quel site où déposer mes SCC ?
Merci
|
|
|
|
|
yes it's true but I didn't want to create a new post if the answer was so simple and already discovered
I have ram 2400 Ballistix with an Intel Celeron Pentium G4920 I would rather 2133mhz it looks like?
|
|
|
|
|
Hi I have the same problem with no image coming out of the DVI socket except with a graphics card plugged into the PCIx16 port BUT I have a 2400Mhz memory module could this be the problem?
|
|
|
|
Hello, there is a link for the firmware of the T9 +? I only see for the S9 thx  |
|
|
|
|
les 2 1060 et la 1070 toujours en vente ? un prix ? merci
|
|
|
|
|
Hello, what do you use as a pool with a 2GB AMD graphics card (AMD 3xx)? and with 2 graphics cards in crossfire does it work?
thx
|
|
|
|
ok thx I try it and I have a fan 12x12cm to cool down
Hi how you configure the Miner Settings generator with the newpacs? thx |
|
|
|
Pi4 2Go with Raspbian, cgminer with the command: ./cgminer -o stratum + tcp: //eu.stratum.slushpool.com: 3333 -u xxx.xxx -p x --suggest-diff 128 --gekko-newpac-freq 200
with Sabrent Hub 7 ports USB 3.0 + 3 smart charging ports, with individual power buttons and LEDs. 60W 12V / 5A power adapter included: https://www.amazon.fr/gp/product/B0797NWDCB |
|
|
|
|
Hello guys, small question I have 2 NewPac keys which operate in frequency of 200Mhz but one of them went down to 181Mhz, do you know how to increase the frequency by command line?
|
|
|
|
try using install manual as you can find on 1st page of this thread. directly on MB, is almost most of time a power problem. of course also depending on your freq settings. Al explained @ 1st page. I recommend you to read this thread carefully completely, because almost all questions already have been asked.  Ok thx, I try it with my new Pi4 |
|
|
|
|
I just installed Xubuntu, followed the procedure according to bitshopper but it does not recognize my 2 keys.
[2019-12-22 12: 15: 05.523] USB all: found 10 devices - listing known devices
.USB dev 0: Bus 7 Device 2 ID: 0403: 6015
** dev 0: Failed to open, err -3
.USB dev 1: Bus 5 Device 2 ID: 0403: 6015
** dev 1: Failed to open, err -3
[2019-12-22 12: 15: 05.523] 2 known USB devices
edit:
I went back to a Win10 on a recent i5, 16GB machine, the 2 keys are plugged into the usb ports on the motherboard, and I don't understand why one is 100% and the other between 80-85% ?
|
|
|
|
|
Hello, I am a novice in the matter, I am starting so I have 2 usb miner;) and I use slushpool, I run this on a T3200 laptop 2.00Ghz, 4GB 64 bits Win7, I have a Sabrent usb hub Hub 7 ports USB 3.0 AC adapter 60W 12V / 5A, I have cgminer-4.11.1-windows-gekko-a62385f, the command line is:
C: \ cgminer \ cgminer.exe -o stratum + tcp: //eu.stratum.slushpool.com: 3333 -u worker.worker -p x --suggest-diff 128 --gekko-newpac-freq 150
you think that it passes or you advise me changes?
thank you
|
|
|
|
Salut à tous, nouveau venu avec plein de questions en tête, en clair un casse c*****e j'ai toujours suivi de loin le BTC mais aujourd'hui j'aimerai me lancer doucement dedans. j'aurai besoin de vos lumières |
|
|
|
Bonjour à tous, je suis un débutant dans le bitcoin même si j'ai jeté plusieurs coup d'oeil sur la question depuis quelques années. J'ai acquis une clé "bitcoin usb-stick miner" de chez bitshopper et j'aimerai me lancer dans l'aventure, mais voilà je suis comme un c** pour créer une adresse btc, j'ai testé bitpay, electrum et greenwallet mais je ne suis pas sûr d'être sur la bonne voie. Pouvez vous m'expliquer comment faire ?merci |
|
|
|
|
