No there is no security breach, all is settled down. Please help with my last question.

Thank you for your answers. Tried static IP and it did not solve the problem. Will try today to make a diagnosis as written above.
I even changed the internet cable and it dit not help.

In the server room are 2 types of internet. The first one is with no acces restrictions. It is the one I connected and the problem is described in my first post.

The second cable, is with access rights. When you logon, the system will ask you to write down your acces login and password.
So, when I install this cable, the system gives an error with the following message: Error: login page Kerion control.
Kerio is the acces manage system that requires the acces data.
But... The mining starts ... But... The Hiveos does not see the rig. So I assume, that if I give the acces rights, all will be working fine.
So... Is there a way to write down the acces data for the Kerio, so at every start the system takes them and connect to the internet?
If yes, what should be my actions to write them  down?

I tried to change the dns as shown in the static ip, but it did not help. Probably i did something wrong.

Hi, tried to find the answer all day, but with no results

Story:

The rig was on Windows, everything was grate. But I decided to go for the Hiveos.
I set the farm at home, everything worked grate one night.

The next day (yesterday) I moved the farm to the server room.
When I connect it to the internet, I receive the message:

Can't connect to eu1.ethermine.org:1444 - host not found (non authoritative), try again later.

The Hiveos sees the farm, but mining is not working.

I am new to the Hiveos. I have read it is a dns problem, but cannot figure it out what to do step by step.

Have to tell, that on Windows the internet is working with no delays.

Will be very thankful for your support!

Well ... I figured it out. My mistake was that I was not starting the bat file or exe file with admin rights. I do not know why this is important, but now all works fine. And it works with Phoenix and with TRM as well.

Thx all for your help and support!

The list-device.bat file showed the 8gb card is under number 4.

The -d 4 command I use with space, and all cards are mining 🤔

Hi I want to use only one card on my rig for mining. In the bat file I wrote "-d 4" at the end of the settings, as I want the number 5 card to work alone.
But when I start the miner it configures all the cards and all the cards are working in mining.

What am I doing wrong?

Please help

I have installed TRM. It works, but the cards are not being selected. I used -d 4 and it did not help. After this I used --device 4 and it did not help.

What other miner you recomand to use only for the ETH mining on the Rx 580 8gb card?

Hi, thanks for your help. I have read  about selecting the only cards to work, but I could not configure it to the end.

So, for RVN, I use the Nbminer. I have set the value "-d 0,1,2,3" and it excluded the 8gb card from mining. All works grate.

As for the ETH, I use the Phoenix Miner. The miner works grate, but if I change the config file, and add the value "-gpus 4" (tried 5, tried <4>, tried <5>, and other ways) the card is not being selected alone. Also with this value added, the miner crashes, and the rig restarts, regardless if Phoenix is working alone or together with the Nbminer.

Hi all!!!

I have an old mining rig that I want to use more effectively. It has 5 cards. Two rx 470 with 4gb and 1 Rx 580 with 8 gb. Currently the rig is mining RVN.


What I want, is to mine with the 8gb card ETH and with 4gb cards to mine RVN.

I heard it is somehow possible, but I did not find any solutions. Can you please help me with that? Or at least show me where to read, or what to look at?

Thanks!

Hi, I have a rig of 5 cards. 4 of them are Saphire Nitro 470 of 4 gb and one is a Saphire nitro 580 of 8 GB. If I install the 8Gb cards in the main slot of the motherboard, then the windows system does not recognize the Rx 580 and one card that is spared with it.
If I put in the main slot one of the 4 Gb card, the minner works fine, and all cards are taking shares.
How to put the 8 Gb card in the main slot and get all the other cards to work?
I changed them with places, but all is the same.

Did that, did not help

Hi!

I have a rig of 4 RX470 with 4GB and one RX 580 with 8 GB. Since yesterday the rig crashes after 10 minutes of activity, the cards with 4 GB do not mine at all. The card with 8GB is minning correctly.

I mine with Claymore miner. This problem is being reported by more miners that mine with Claymore. My question is:

Do you have the same problem with the Phoenix miner? I would like to know, so I can try installing the Phoenix miner to test if it solves the problem.