Bitcoin Forum
June 24, 2024, 07:20:38 AM *
News: Latest Bitcoin Core release: 27.0 [Torrent]
 
  Home Help Search Login Register More  
  Show Posts
Pages: [1]
1  Alternate cryptocurrencies / Mining (Altcoins) / Re: [ANN] TeamRedMiner 0.8.0 - Ethash/Kawpow/Nimiq/Etchash and More on: February 04, 2021, 08:56:02 PM
hi,

i tried to flash my vega 64 nitro with the 56 bios on hiveos.
its going wrong and my card didnt get recognized,
can anyone help me to flash it back?
or with the correct 56 bios, and how to see the card?
thx

i got it.

the vega runs with 54 mh/s at 1100 on core and 1028 on mem with 850 mv on both.
tweak timings cl 20 ras 26 rcdrc 12 rcdwr 12 rc 38 rp 12 rrds 3 rrdl 5 rtp 6 faw 12 cwl 8 wtrs 4 wtrl 9 wr 13 ref 15600 rfc 239

is there better settings with the new trm v8.0?
i run it on windows, with 4 vega 56 power coler at 48 mh and 1 vega 56 phantom on 51mhs (morpheus cooler) mem temp set on 62
i've i try to overclock in hive i got many errors with powerplay table.
What do i wrong?
Is there an hashrate increase of switching to hive? when it runs?

thx
2  Alternate cryptocurrencies / Mining (Altcoins) / Re: [ANN] TeamRedMiner 0.8.0 - Ethash/Kawpow/Nimiq/Etchash and More on: February 01, 2021, 08:37:31 PM
hi,

i tried to flash my vega 64 nitro with the 56 bios on hiveos.
its going wrong and my card didnt get recognized,
can anyone help me to flash it back?
or with the correct 56 bios, and how to see the card?
thx
3  Alternate cryptocurrencies / Mining (Altcoins) / Re: [ANN] TeamRedMiner 0.7.22 - Nimiq/Kawpow/Ethash/Etchash/Cryptonight and More on: December 27, 2020, 08:38:24 PM
Hy,

i have vegas 56 hynix and are running it with blockchain driver, should i switched to the newest adrenalin?

thx.
4  Alternate cryptocurrencies / Mining (Altcoins) / Re: [ANN] TeamRedMiner 0.7.18 - Nimiq/Kawpow/Ethash/Etchash/Cryptonight and More on: December 13, 2020, 04:32:12 PM
hi,

i'm new on TRM. i have 4 vega red evil 56 card hynix ,with my settings from claymore i get a hashrate on 43mh/s
930mhz mem 1050 core on 900mv can't get the mem higher.
 i try modded the mem timings with the amdmemorytweakxl tool.

i always get the 43mh/s
i'm not sure i've im doing it right. try the changes from the ethgenreraltuning list in tweak tool. apply.

does TRM auto tuning reset this settings? or do i have to add anything in the command line?

thy

The 43 MH/s is the classic limit at stock timings, so it really sounds like the changed timings aren't being applied properly for you. The miner doesn't touch anything related to clocks/voltages/timings, only the fan curve if you have fan control enabled.

It's hard to say why the timings aren't being applied. If you start the miner and let it run for a few mins, then open amdmemtweakxl and e.g. boost tREF to 17000 or make a slight adjustment down for tRCDWR and apply the changes, does the hashrate move in the miner? If not, what timing are displayed of you close+reopen amdmemtweakxl, are your changes there?

hi, thx

now i got 46 mh/s with 1700 on ref and 20rcdrd and 4 rcdwr. there was no diference with rcdwr starts on 10.

does the settings from tweak tool reset after pc restart? watchdog is enabled with restart the system.
can i set a target temp for fan with command line ? or just settingfan speed?

My bad, I wrote rcdwr but really meant rcdrd. That's the one you want to lower slowly. Also, did you do 1700 or 17000 for ref?

For fan control, you can target a core temp, junction temp, or mem temp, set the initial fan speed or a static fan speed. Use --fan_control --fan_default_vega=::70:60 to target 70C mem temp with fans initially at 60%.


I start with 17000 on ref an go down to 18 on rcdrd but it was  not stable. ref is now on 15600 and rcdrd 20 is stable for a few hours. hashrate is 46mh/s. i set the target temp on 55
But on restart the settings are lost.


thanks a lot!

one more question. i now run the vegas with ref 15600 rc 35 rcdrd 19 get 47 mh/s hashrate when auto tune set konfig on a1024.
but autotune set is not erverytime the same for example now 1 card is on eth config a736 and there are only 44mh's hashrate . Same cards with the same settings.

Can i set the eth config fix in the command line? or start autotune new?
and i need help with a batch file for amd tweak tool for startup i've the amdtweaktoolxl and i wrote

(folder of tweak toolxl...).exe --i 0,1,2,3,4,5 --rcdrd 19 --REF 15600 --rfc 164 --rc 35

it opens the tweak tool but didn't set any settings?

thx
5  Alternate cryptocurrencies / Mining (Altcoins) / Re: AMD Mem Tweak XL - Read/modify timings/pp/straps on the fly on: December 11, 2020, 05:59:46 PM
hi,

can anyone help me to write a batch file?

i start with
folder of tweak tool....exe --i 0,1,2,3,4,5 --rcdrd 19 --REF 15600 --rfc 164

it runs the tool but nothing is changing

thx
6  Alternate cryptocurrencies / Mining (Altcoins) / Re: [ANN] TeamRedMiner 0.7.18 - Nimiq/Kawpow/Ethash/Etchash/Cryptonight and More on: December 09, 2020, 08:54:31 PM
hi,

i'm new on TRM. i have 4 vega red evil 56 card hynix ,with my settings from claymore i get a hashrate on 43mh/s
930mhz mem 1050 core on 900mv can't get the mem higher.
 i try modded the mem timings with the amdmemorytweakxl tool.

i always get the 43mh/s
i'm not sure i've im doing it right. try the changes from the ethgenreraltuning list in tweak tool. apply.

does TRM auto tuning reset this settings? or do i have to add anything in the command line?

thy

The 43 MH/s is the classic limit at stock timings, so it really sounds like the changed timings aren't being applied properly for you. The miner doesn't touch anything related to clocks/voltages/timings, only the fan curve if you have fan control enabled.

It's hard to say why the timings aren't being applied. If you start the miner and let it run for a few mins, then open amdmemtweakxl and e.g. boost tREF to 17000 or make a slight adjustment down for tRCDWR and apply the changes, does the hashrate move in the miner? If not, what timing are displayed of you close+reopen amdmemtweakxl, are your changes there?

hi, thx

now i got 46 mh/s with 1700 on ref and 20rcdrd and 4 rcdwr. there was no diference with rcdwr starts on 10.

does the settings from tweak tool reset after pc restart? watchdog is enabled with restart the system.
can i set a target temp for fan with command line ? or just settingfan speed?

My bad, I wrote rcdwr but really meant rcdrd. That's the one you want to lower slowly. Also, did you do 1700 or 17000 for ref?

For fan control, you can target a core temp, junction temp, or mem temp, set the initial fan speed or a static fan speed. Use --fan_control --fan_default_vega=::70:60 to target 70C mem temp with fans initially at 60%.


I start with 17000 on ref an go down to 18 on rcdrd but it was  not stable. ref is now on 15600 and rcdrd 20 is stable for a few hours. hashrate is 46mh/s. i set the target temp on 55
But on restart the settings are lost.
7  Alternate cryptocurrencies / Mining (Altcoins) / Re: [ANN] TeamRedMiner 0.7.18 - Nimiq/Kawpow/Ethash/Etchash/Cryptonight and More on: December 09, 2020, 02:12:19 PM
hi,

i'm new on TRM. i have 4 vega red evil 56 card hynix ,with my settings from claymore i get a hashrate on 43mh/s
930mhz mem 1050 core on 900mv can't get the mem higher.
 i try modded the mem timings with the amdmemorytweakxl tool.

i always get the 43mh/s
i'm not sure i've im doing it right. try the changes from the ethgenreraltuning list in tweak tool. apply.

does TRM auto tuning reset this settings? or do i have to add anything in the command line?

thy

The 43 MH/s is the classic limit at stock timings, so it really sounds like the changed timings aren't being applied properly for you. The miner doesn't touch anything related to clocks/voltages/timings, only the fan curve if you have fan control enabled.

It's hard to say why the timings aren't being applied. If you start the miner and let it run for a few mins, then open amdmemtweakxl and e.g. boost tREF to 17000 or make a slight adjustment down for tRCDWR and apply the changes, does the hashrate move in the miner? If not, what timing are displayed of you close+reopen amdmemtweakxl, are your changes there?

hi, thx

now i got 46 mh/s with 1700 on ref and 20rcdrd and 4 rcdwr. there was no diference with rcdwr starts on 10.

does the settings from tweak tool reset after pc restart? watchdog is enabled with restart the system.
can i set a target temp for fan with command line ? or just settingfan speed?
8  Alternate cryptocurrencies / Mining (Altcoins) / Re: [ANN] TeamRedMiner 0.7.18 - Nimiq/Kawpow/Ethash/Etchash/Cryptonight and More on: December 09, 2020, 07:48:09 AM
hi,

i'm new on TRM. i have 4 vega red evil 56 card hynix ,with my settings from claymore i get a hashrate on 43mh/s
930mhz mem 1050 core on 900mv can't get the mem higher.
 i try modded the mem timings with the amdmemorytweakxl tool.

i always get the 43mh/s
i'm not sure i've im doing it right. try the changes from the ethgenreraltuning list in tweak tool. apply.

does TRM auto tuning reset this settings? or do i have to add anything in the command line?

thy
9  Alternate cryptocurrencies / Mining (Altcoins) / Re: PhoenixMiner 5.3b: fastest Ethereum/Ethash miner with lowest devfee (Win/Linux) on: December 02, 2020, 07:46:58 PM
Hy,

I'm new at Phoenix, Hashrate is lower than on claymore but it works. So I try for dual mining, but didn't get a hashrate on the secand coin.
Copy the command line from the readme for dual mining and added my adresses.
Any tips, thx



What are you trying to dual mine....some coins like zil only mine for a short period every few hours.


Hi,

Blake2s

ETH on ethermine.org ETH, Blake2s on Nicehash:
      PhoenixMiner.exe -pool ssl://eu1.ethermine.org:5555 -pool2 ssl://us1.ethermine.org:5555 -wal YourEthWalletAddress.WorkerName -proto 3 -dpool blake2s.eu.nicehash.com:3361 -dwal YourBtcWalletAddress -dcoin blake2s

B2S New Jobs getting in but speed is always zero. ETH Speed is on 39MH/s on vega 56, with claymore it was 41.That's OK for me and it looks stable.
thx
10  Alternate cryptocurrencies / Mining (Altcoins) / Re: PhoenixMiner 5.3b: fastest Ethereum/Ethash miner with lowest devfee (Win/Linux) on: December 02, 2020, 05:17:32 PM
Hy,

I'm new at Phoenix, Hashrate is lower than on claymore but it works. So I try for dual mining, but didn't get a hashrate on the secand coin.
Copy the command line from the readme for dual mining and added my adresses.
Any tips, thx

Pages: [1]
Powered by MySQL Powered by PHP Powered by SMF 1.1.19 | SMF © 2006-2009, Simple Machines Valid XHTML 1.0! Valid CSS!