 Show Posts
|
|
Pages: [1]
|
|
under Current miners, it shows 0...
I can't see my miners, so I have pulled them until this issue is resolved.
|
|
|
|
Has anyone done the S1 conversion to an S3 yet with the upgrade kit?
if so, did it work?
We tried it and get no hashing from the new boards, show up like this,
xxxxxxxxxx xxxxxxxxx ooooooooo ooooooooo
xxxxxxxxxx xxxxxxxxx ooooooooo ooooooooo
have tried 2 sets of new S3 boards, same issue,
What am I missing?
I haven't upgraded the firmware as of yet, could that be the issue?
The kit instructions say nothing about upgrading firmware..
What about the Frequency, S3's run at 218.75, S1's run at 350..
not a word in the instructions if I should change Frequency's...
Any ideas??
The trick is to upgrade the firmware to the latest S3 version, We have it running at the S3+ frequency 225....runs @ 450ghs+... temps 38c. |
|
|
|
*I have not received my kits yet, I was on the first order but still has not shown up yet, when did you get your kits  Ours showed up on the 19th. But we haven't had any luck in getting them working yet... |
|
|
|
|
Has anyone done the S1 conversion to an S3 yet with the upgrade kit?
if so, did it work?
We tried it and get no hashing from the new boards, show up like this,
xxxxxxxxxx xxxxxxxxx ooooooooo ooooooooo
xxxxxxxxxx xxxxxxxxx ooooooooo ooooooooo
have tried 2 sets of new S3 boards, same issue,
What am I missing?
I haven't upgraded the firmware as of yet, could that be the issue?
The kit instructions say nothing about upgrading firmware..
What about the Frequency, S3's run at 218.75, S1's run at 350..
not a word in the instructions if I should change Frequency's...
Any ideas??
|
|
|
|
I would use a separate RPi for the Hurricane. I've been running 6 gridseeds (5.2mhs each)now for months @ a clock of 838 and the run flawless on minera..
just got my ZeusMiner Hurricane X3 (15mhs) and I was wondering if it possible to run
the 6 Gridseeds and a Zeus Hurricane x3 on the same RPi using Minera?
or should I just get another RPi for the Hurricane?
Thanks..
I was thinking that since CGminer Dmaxl Zeus fork should run both the gridseeds and the Zeusminers, then I would just need to set the frequency's for them in the option tab.. I think the zeusminer is done like this -S zus:all --set zus:chips=64 --set zus:clock=328 but I'm not sure about the gridseed settings. -S gridseed:all --set-device gridseed:clock=838 or "gc3355-detect": true, "freq": "838".. |
|
|
|
|
I've been running 6 gridseeds (5.2mhs each)now for months @ a clock of 838 and the run flawless on minera..
just got my ZeusMiner Hurricane X3 (15mhs) and I was wondering if it possible to run
the 6 Gridseeds and a Zeus Hurricane x3 on the same RPi using Minera?
or should I just get another RPi for the Hurricane?
Thanks..
|
|
|
|
|
I don't mind setting up to mine the most profitable site of the 2 (NiceHash and WestHash), I just wish your overall balance of the sites were combined and were paid out in one shot not separately..
just not sure how to do that with my setup..
My 8 Gridseeds are running fine on NiceHash, using a raspberry Pi with the Minera web face..
|
|
|
|
|
Been mining here for a few days and have 0.02531212 ready for payout.
I feel I should have had 2 payouts by now.
Can someone tell me when I can expect my payout?
Here' my address 1bQQKrNBbGT3zdmJpz7Jos8F6MBBWCstw.
Thanks..
|
|
|
|
|
miners are not mining...
bitminter.com not responding!
|
|
|
|
I've now got one card running happily at 850mhz, and one at 887mhz - ie. about 670gh/s and 690gh/s
VinceSamios Nice work, what temps are you running? Best I can do with my card so far is 625gh/s @ 850mhz running 73c using .84v. It was tested at 689gh/s @800mhz and .88v according to the masking tape that was on it... |
|
|
|
Well I am sad to report that my GR card is no longer recognized by any system after I plugged in an additional fan to the board (fan 2 header). I am now at a loss. The board powers up with the normal lights and the normal indicators when USB is plugged in. after that, nothing is recognized.
What I did to "cause" this...
1. All systems running stable ~600GH/s @ ~90C @ 800MHz
2. Power Card down
3. Plug additional fan into fan2 header pins
4. Power up card (new fan was spinning)
5. nothing, card usb not seen by multiple systems.
Anyone have any troubleshooting ideas here?
I contacted Ken and company but have had no response.
My card was running off and on (off for liquid block placement) for roughly <2 weeks total.
Thanks!
Had the same thing the other day, I pushed the reset button on the card, it rebooted and showed up on my pc. |
|
|
|
So in reality, this card is really 550 GH/s to 600 GH/s for $849 when you can get 3 Ants for $600?
...With ~X2+ the power consumption for the S1s, but so far, yea that is what I see... I really wish I could get any feedback from Ken (and/or company) on what is going on with the performance of the board. So far I am under spec...  My results mirror what your getting, I just can't keep it cool enough to run 800mhz with the corsair H80i. Think we are going to order some parts and build our own cooling system. |
|
|
|
I am hoping someone will find fault on my rig setup and be the answer to getting the card up to spec...
Corsair HX750M PS + Corsair H110i cooler + 1-coolermaster 240MM fan cooling the board + good exhaust for the radiator (this same exhaust keeps a small room /w 4 S1's @~72F)
-I used the procedure in the Prospector card thread to attach the cooler using the 8/32 nuts.
-Cleaned and re-applied thermal paste on the board and cooler.
-The PS has all 4 Pci-e plugs attached
-I tested the OC from 400MHz-850Mhz and found the board hashed no faster and only created more heat for no gain... I let the board run for ~1 hour for testing at different OC levels.
-Getting <600GH/s steady @775MHz @~87C
I am beginning to think this is a card problem... Anyone else have a different outcome?
Having the same issue's as you, same PSU, running the H80I cooler, extra fan blowing across the board. Followed the Prospector card procedure to attach everything and I can only average 600ghs @ 800mhz @ 91c-93c. Anyone have an idea on how to get over 700ghs? Masking tape test results on ours showed 689ghs @.88volts and 800mhz...can't get anywhere close to that number, even running an ice chilled water cooling system @ 800mhz still only pulls 600ghs average @ 90c. What base are you using with the water block? I used the block of aluminum that came with the OGR card. The base that came with the H110i has threaded standoffs that were too long going through the board and would never work. I used the same base you did, had the same problem. |
|
|
|
I am hoping someone will find fault on my rig setup and be the answer to getting the card up to spec...
Corsair HX750M PS + Corsair H110i cooler + 1-coolermaster 240MM fan cooling the board + good exhaust for the radiator (this same exhaust keeps a small room /w 4 S1's @~72F)
-I used the procedure in the Prospector card thread to attach the cooler using the 8/32 nuts.
-Cleaned and re-applied thermal paste on the board and cooler.
-The PS has all 4 Pci-e plugs attached
-I tested the OC from 400MHz-850Mhz and found the board hashed no faster and only created more heat for no gain... I let the board run for ~1 hour for testing at different OC levels.
-Getting <600GH/s steady @775MHz @~87C
I am beginning to think this is a card problem... Anyone else have a different outcome?
Having the same issue's as you, same PSU, running the H80I cooler, extra fan blowing across the board. Followed the Prospector card procedure to attach everything and I can only average 600ghs @ 800mhz @ 91c-93c. Anyone have an idea on how to get over 700ghs? Masking tape test results on ours showed 689ghs @.88volts and 800mhz...can't get anywhere close to that number, even running an ice chilled water cooling system @ 800mhz still only pulls 600ghs average @ 90c. |
|
|
|
Are you running @ 800mhz and what kind of temps are you getting?
defualt mhz is 550 and that only got me 360 ghs.
700mhz gets me 500ghs @ 88c.
Can I push it to 800mh?
It was tested @ 800mhz and run 689ghs but I don't
know how what they used to cool it with.
whats the need for the usb running from the pump?
I powered mine from the sata power cable from the ups.
any info is greatly welcomed,
Thanks
I am getting about the same results setup the same way. @ 800 mhz I was ~91C @ ~700 GH/s. What kind or cooler are you using, I don't think the corsair H80I is big enough to keep it cool. |
|
|
|
|
How do I tweak the voltage on a Gold Rush card? it's running 0.83 to 0.84 and I want 0.88.
|
|
|
|
|
mine shipped from Reno, Nevada.
|
|
|
|
|
Are you running @ 800mhz and what kind of temps are you getting?
default mhz is 550 and that only got me 360 ghs.
700mhz gets me 500ghs @ 88c.
Can I push it to 800mhz?
It was tested @ 800mhz and ran 689ghs but I don't
know how or what they used to cool it with.
whats the need for the usb running from the pump?
I powered mine from the sata power cable from the psu.
any info is greatly welcomed,
Thanks
|
|
|
|
|
Any chance that you will post a setup guide for the Gold Rush card like you did for the Prospector card?
Since the card came with zero instructions on how to set it up, I just don't want to guess at the power setup.
The card has 4 pcie power connectors but the box says you need dual pcie power connectors so I'm a bit confused.
Thanks.
|
|
|
|
|
