Latest posts of: mconstenla11

Show Posts
Pages: [1]

on: June 05, 2015, 12:43:39 AM

Good Night my Friends Does somebody knows if i can connect this fan (Sanyo-Denki-San-Ace-120) as a secondary fan for the s5 antminer?? And if so, could i have a problem due to the amperage consumption in the controller board?? Here it is the link of this fan on ebay: http://www.ebay.com/itm/NEW-Sanyo-Denki-San-Ace-120-PWM-Fan-3A-224-CFM-120mm-12V-9GV1212P1J091-/361311523885?pt=LH_DefaultDomain_0&hash=item541fd8542d Thanks a lot for help .

on: April 08, 2015, 05:53:22 PM

Quote from: notlist3d on April 08, 2015, 05:46:24 PM Quote from: mconstenla11 on April 08, 2015, 05:27:22 PM hi. I would like to know the speed of each fan for this cooling kit?? Because i was wondering, if want to extract all the air that is expelled from the radiator i should know all the volume of air i must remove from the room where the mining machines are working. Thanks a lot Sadly I don't think you will get a response on forum syscoolings account: Last Active: March 21, 2015, 09:35:43 AM You stand a better chance emailing them at this point I think. And what are your thoughts on mantaining the room temperature right? should i install 12000 btu per hour of air cond for each radiator set that is about 3500 w max, (3500 watts = 11950 btu per hour). Or should extract the same amount of heated air from the room, measuring how volume of air this radiator set works with??? Thanks My friend

on: April 08, 2015, 05:27:22 PM

hi. I would like to know the speed of each fan for this cooling kit?? Because i was wondering, if want to extract all the air that is expelled from the radiator i should know all the volume of air i must remove from the room where the mining machines are working. Thanks a lot

on: December 10, 2014, 03:52:02 AM

Quote from: dogie on December 10, 2014, 03:19:10 AM Quote from: notlist3d on December 10, 2014, 02:44:30 AM Quote from: mconstenla11 on December 10, 2014, 02:34:56 AM hello i have just recieved 4 C1 's, i installed them and 3 of them work perfectly and are mining as i write this, but i have one machine that did not connect with 192.168.1.99 and so i proceeded to reset , once i reset it connected for seconds yet it had no values,and disconected again can you please advise me as soon as possible? what are your recommendations on this???. Thanks a lot. Have you tried using the image in 2nd post on card? If you are not able to connect to it the image should set it back it default IP. Assuming you looked at router to see if it is under different IP, and ping it to make sure it's not there that is what i would try. Please correct me Dogie if you have better idea. Yeah start with SD card image. please, wich it is the 2nd post on card? i cant find it.

on: December 10, 2014, 02:34:56 AM

hello i have just recieved 4 C1 's, i installed them and 3 of them work perfectly and are mining as i write this, but i have one machine that did not connect with 192.168.1.99 and so i proceeded to reset , once i reset it connected for seconds yet it had no values,and disconected again can you please advise me as soon as possible? what are your recommendations on this???. Thanks a lot.

on: October 15, 2014, 09:27:50 PM

Hello , someone will have idea about what may be going to the board 11 which stopped working from one moment to another

on: October 15, 2014, 09:00:50 PM

Quote from: helipotte on October 15, 2014, 04:50:15 PM Maybe. I know I had some chips the "misbehaved" until I updated. Can't hurt. Check the frequency also. One of my tubes had a blade that chips would disappear on. Had to clock that one at 260 to get all of them working. And keep it super cool (2 fans). after updating my board cards listed as board 11 dead. what could be?

on: October 15, 2014, 05:12:48 PM

Quote from: helipotte on October 15, 2014, 04:50:15 PM Maybe. I know I had some chips the "misbehaved" until I updated. Can't hurt. Check the frequency also. One of my tubes had a blade that chips would disappear on. Had to clock that one at 260 to get all of them working. And keep it super cool (2 fans). and takes a lot to make the upgrade to the boards? I did about 20 minutes ago and is still the same version

on: October 15, 2014, 04:46:37 PM

Quote from: helipotte on October 15, 2014, 04:38:11 PM Looks like you have old firmware, type in: 192.168.1.223:8000/Flashmega to update it. Current version is 1.41 or 1.53 and you think that's the cause of the card 11 is stopped?

on: October 15, 2014, 04:28:35 PM

Good afternoon , someone will have idea about what may be going to the board 11 which stopped working from one moment to another and that was 4 days ago

on: June 13, 2014, 03:52:18 PM

Quote from: solosequenosenada on May 26, 2014, 05:54:55 PM Son cupones descuento, si vas a adquirir un Antminer S2 te descuentan 400$ del precio final. Si estas interesado deja la id de bitmaintech. Buenos dias amigo, estoy por realizar la compra de antminer s2 por bitmaintech.com y te agradecería si me puedes enviar un cupon a mi ID que es ´´verdugin´´ , muchísimas gracias de ante mano!

Pages: [1]