 Show Posts
|
|
Pages: [1]
|
|
Cannot change mining pools in settings. Any advice?
|
|
|
|
Seems like as long as the SD card is good, the C1 is a very reliable miner. I had some issues with mine on startup but wiping the SD card and uploading Dogie's original disk image got me up and running. Anyone have better uptime yet?  What is your voltage setting? 0760? |
|
|
|
On C1, with 218.75M(default) what voltage should i set, currently is 0760. Is it ok, because im not getting over 950ghs
First, you need to ensure that your C1 is NOT running the November firmware before you can change the default setting. This thread is beyond that scope, but a lot has been said in the S3 discussion and support thread. The datasheet setting for the freq range of 225 (which I'd say 218.75 falls) is 0.72v, so I'd test with a voltage setting of 0720 which should be more than adequate for that freq. Again, do at your own risk! November firmare as i can see " File System Version Wed Nov 26 10:27:37 CST 2014" |
|
|
|
|
On C1, with 218.75M(default) what voltage should i set, currently is 0760. Is it ok, because im not getting over 950ghs
|
|
|
|
|
Hello guys,
Anyone that has C1, is your hash speed consistent or not?
My average is 812 with variations from 767 to 1000 gh/s
|
|
|
|
So, what's the conclusion, on what pool should we mine  |
|
|
|
tubes for the radiators soften if the miner has temperature over 40C
Thats.... thats just physics... Physics yeah, for the "quality" of the tubes. |
|
|
|
|
C1 arrived in a record time. Miner is ok, but the cooling kit is the worst thing i have ever seen. The water pump leaked on the first power up and died after 1 minute work, wiring for the fans is bad soldered and the wires are so thin, tubes for the radiators soften if the miner has temperature over 40C. They should take care about this. Syscool should raise the price for 5-10 usd and sell quality not quantity ! ! ! Next purchase will be only miner. I dont need crap
|
|
|
|
|
Loan amount: 0.013(was 0.014)
Repayment : 0.017
Duration : End of December(or sooner)
BTC : 15ZCnfnkQxFjWFTpvbdtUw21XWCTUhdNKM
Reason : Pay rest of invoice @ Bitmain for C1 miner
|
|
|
|
|
Give me your btc address for the help
THANK YOU VERY MUCH !
Transfer will be made asap when the coins will be on my wallet
|
|
|
|
|
OK, give me directions please ! If you help me i will delete this thread and credit you with 0.0025 !
|
|
|
|
|
As you said the bad thing is that im new to this forum. My problem is that ive paid to bitmain for a miner but banks killed me with the fees(bank wire transfer) and im short with usd19. Ive collected usd14 from altcoins(quark) but it is taking too much time to make to usd19.
If anyone has account on payza or skrill i can transfer money instantly ! ! !
This is my address(its on Cryptsy, not personal wallet) so it is up to you.
15ZCn fnkQx FjWFT pvbdt Uw21X WCTUh dNKM
|
|
|
|
|
Hi guys,
I need a loan of 0.015 btc
I am new to this forum because im stuck with the payment services. Any exchange like buying something or paying a service with credit card is accepted. If some one wants to lend me this ammount will get it back till the end of december with 25% interest (0.0185 btc)
Thanks in advance
|
|
|
|
|
