That worked a treat :-) Thank you

I keep my wallet running in the system tray as I think it helps new wallets sync up quicker :-)

I tried making a transfer of 0.001 to Finebox but I didn't think much before accepting the wallets default transaction fee of 0.00000002 and its been stuck for over 5 days.
Is there anyway to add more to the transaction fee?

I've had so many fan failures I ran out of spares and found a temporary solution until the new ones arrived.
It only seems to be the Sj brand that loses the speed sensor after about 6 months although the fan is working fine.
I've also started having YaLn (Yate Loon) fans fail and completely stop.
Near the faulty fan cut the yellow wire and bare the end that goes to the plug. Then slightly bare the yellow wire (using a lighter flame to soften the plastic) on the working fan. Twist the broken fan wire around the working fan wire and cover with tape. This will make the controller show both fans at the same rpm. I think the reason the Sj fans are failing is because the tiny magnetic speed sensor stops working. Ultraflow fans seem really good but it's hard to find a low cost supply.

This command works really well with 'Awesome miner', I've setup an 'Action' button that allows me to shutdown all the miners
without switching them off when hot. I think this might extend the life of the chips as they won't get so hot.

Hi Lasergun,
Dug an old laptop from the loft and found I'm another who missed the swap, can I send my wallet.dat ?

Regards
Gadget

Found that 'shutdown -h now' makes it restart. 'halt' seems the best way to avoid a 'hot' power off

Thanks for your response, with my batfile exactly as you said and with those clock speeds i get about 16MH/s and it sometimes flashes up 20mh/s
http://puu.sh/nL3ws/d9d4971838.png

Hi guys, I saw a rig on a site called omg it works and it claimed "Adapter 5 – MSI Lightning 7970 @ 1200 / 1500: 28,9 MH/s Sensor 0: Temperature – 76.00 C"
So I went and bought a MSI Radeon 7970 Lightning BE and it arrived this morning, I've set up ethminer and ethproxy but I'm only getting about 17 sometimes 18mh/s on ETH

"
setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_USE_SYNC_OBJECTS 1
ethminer.exe -G --opencl -F http://127.0.0.1:4052/miner/17/Lightning --opencl-platform 0 --opencl-device 0 --farm-recheck 500 --cl-global-work 16384 --cl-global-work 8192
pause
"
This was slow before I added those arguments, too, if I'm missing any arguments that would increase my speed let me know
I've tried moving all the clocks around in msi afterburner and also moved the voltages around but nothing seems to make a difference apart from sometimes the miner will flash 20mh/s at me for one line and go back to 18 for a while
I'm thinking maybe I have the wrong drivers or something...
http://puu.sh/nKCal/803e372f51.png
If you can help me fix it I will send you 5$ in btc or mine @ around 32mh/s to a pool of your choice for 12 hours (I'll use my old 770 too)

Thanks in advance

Try adding these nodes to your spaincoin.conf
I found putting the computer on DMZ helped find a node

addnode=77.27.60.211
addnode=85.236.188.28
addnode=88.11.233.146
addnode=204.11.237.233
addnode=178.33.209.212
addnode=178.7.17.201
addnode=109.124.222.116
addnode=194.249.178.189
addnode=82.26.208.67
addnode=193.227.134.111
addnode=192.99.6.207
addnode=23.21.204.34
addnode=192.99.47.133
addnode=188.99.43.160
addnode=201.176.137.105
addnode=188.105.99.185
addnode=188.98.252.41
addnode=212.107.130.19

After turning off my firewall I was able to find these working nodes...

addnode=193.227.134.111
addnode=204.11.237.233
addnode=192.99.6.207
addnode=23.21.204.34
addnode=192.99.47.133
addnode=188.99.43.160
addnode=201.176.137.105
addnode=188.105.99.185

I want to move all my coins to Cryptsy but I can't find any working nodes.

Ok, I've sent that back, but it said it was over the size limit! lol

Status: 1/unconfirmed, broadcast through 1 node
Date: 15/06/2015 08:42
To: to sirslayer 4EHG3NKuvHUNQx629u8JLrrw3JxVHZNUyJ
Debit: -0.00000001 42
Transaction fee: -0.00000011 42
Net amount: -0.00000012 42
Transaction ID: a7955d948450d6c6ed7c82f9ecd238fe8d542445bfe062e70991288c0680abbe

Hi sirslayer, my address 4PD4F5NpVZu7zRxUzHfiioZBLkx5qydtE8

cheers

I've not tried setting a manual transfer fee yet as I don't want to risk another 0.01 fee.
My version

I've looked at that option in both wallets but its not selected..

I have 2 wallets on separate computers and wanted to transfer funds from PC to Laptop. As a precaution I tried a test transfer of 0.00000001 which also had a fee of 0.00000002
For some very weird reason the wallet I was sending the payment too sent a payment of 0.01 (about $8) to this unknown address 4csTKT2ftvW6ReJzKsGmbNgNn7cxqLD8jX .
Can anyone explain what's going on?

Wallet on PC..

Wallet on Laptop

As you can see from the screenshot I've been earned a few payments from leaving the wallet online.
But now its going to be 17 years before the next reward, is this normal?

Have you tried 'Reset to factory settings on the System tab?

Any problems I've had with cubes not showing or working properly has always been fixed with this option.
I thought my controler board had gone wrong when none of the cubes would show, but this reset brought them all back online.

Hi Mario, here's the one you want http://noble.ilikebtc.com/NobleCoin-Qt-v2.0.1.zip

Make sure you send a few 'test' coins from your Cryptsy acount to make sure its working ok before you do the full amount.

I've just found I was mining on the old fork and have lost just under 1 million coins :-(

Ok thanks for the info. I've looked at my original wallet and it shows I mined from 7th March. Luckily I have 47k in my Cryptsy account.
Would it be worth paying that into the new wallet to earn pos?