 Show Posts
|
|
Pages: [1]
|
Rig: 6xRX480 Sapphire Nitro +OC 8GB, Windows 10. I use HWINFO64 to inspect the memory errors reported by each card, and so should you. The rig has been mostly stable 175-180Mh/s for the last six months or so using Jukebox v4.rom bios on most and vdrop+.rom on one. Recently I have had to lower the memory overclock and bump up the voltage 6.25mv on all my cards since Epoch #130. (WattTool -16 to -15) I think what is happening is we're using more of the RAM in the new epochs so the bleeding-edge overclock that was stable before no longer isn't. So since these changes we're stable again, but with 168Mh/s instead of 178Mh/s.  Yeah sounds about right |
|
|
|
Having any issue. Using Claymore dual miner v9.5
Yesterday I inadvertently restarted a machine that had been symptom free for more than 100 hours. After restart 4 of my GPUs were reading between 27-28 Mh/s and the 5th was just over 4 Mh/s. I disabled that miner, isolated it and ran it by itself. The card hashes ~27 Mh/s by itself. Plugged them in one by one and until I get to the 5th card everything runs normal.
I moved to another machine, different motherboard different cards and the same thing is happening to this machine now as well.
Can anyone offer an explanation?
Got the same thing here, I am currently trying to slowly increase clock speeds as all six will run together at around 13mh/s (rx480's) Not sure if this is a power issue,but i dont think so as i have corsair hx1200i and all the right parts. In the right place.I think... |
|
|
|
Hello,
I am using Ethos and would like to run claymore with 6 gpu
hope someone could point me in the right direction here (please !)
You have to believe me here when i say that i have tried absolutley everything
i have read here but i just cannot get 6 gpu working with this motherboard.
With Claymore each gpu is at least 2 mh/s faster
With ethminer i can run 5 stable(3 days)
with both sgminer and claymore's the 6 gpu will start up and hash at 27 or so and the cut down to 4
after 1 or 2 minutes.
With sgminer it also does me the courtesy of telling me that the 2 gpu are sick then dead.
This can be with any card in any slot,it always changes.
I think somehow that that is the important part ?
All cards and risers work fine and have been checked in different slots,different risers,individually,
in groups and any combination you can think of.
All the info on here i can find i have followed.
So that's 4 gpu with claymore and sgminer,
and 5 with ethminer.
This is my first build and i have really enjoyed it so far,im looking forward to making more hopefully.
but i have now been banging my head against a brick wall for 2 weeks now(starting to make a mess)
Anyway i hope someone here has a clue for me.
Cheers
Provide more information about your setup: makes, models, versions, parameters, screenshots, troubleshooting steps taken... Sorry i forgot to post this bit: Operating system:Ethos mobo:Z170A GAMING PRO CARBON (MS-7A12) ram:4g Intel(R) Celeron(R) CPU G3900 @ 2.80GHz drive_name: KINGSTON SV300S37A120G GPU: 6x XFX rx480 8g one of which is the gtr black edition. PSU: Corsair hx1200i I have the same PSU, GPUs and CPU... Different MB and Win10. 6 cards in each rig. I have Z170 MB which I use for testing. If I have a spare time I might try to run 6 cards on it. If I were you I would try to seriously downvolt and downclock the cards, let us say half speed, to make sure that this is not related to current, voltage and temperature. If 6 runs with minimal speed than you can rule out drivers, OS, power and etc. I have seen comments that Z170A are the most problematic when it comes to 5+ cards. Have you tried another mobo? Thanks, i put them down to half speed and its been running for over a hour now at a stable 13 mh/s per card , What would you recommend next,slowly increase ? i dont have another motherboard to try. thanks for your help |
|
|
|
|
Operating system:Ethos
mobo:Z170A GAMING PRO CARBON (MS-7A12)
ram:4g
Intel(R) Celeron(R) CPU G3900 @ 2.80GHz
drive_name: KINGSTON SV300S37A120G
GPU: 6of: XFX rx480 8g one of which is the gtr black editition.
PSU: Corsair hx1200i
Hello,
I am using Ethos and would like to run claymore with 6 gpu
hope someone could point me in th right direction here (please !)
You have to believe me here when i say that i have tried absolutley everything
i have read here but i just cannot get 6 gpu working with this motherboard.
With Claymore each gpu is at least 2 mh/s faster
With ethminer i can run 5 stable(3 days)
with both sgminer and claymore's the 6 gpu will start up and hash at 27 or so and the cut down to 4
after 1 or 2 minutes.
With sgminer it also does me the courtesy of telling me that the 2 gpu are sick then dead.
This can be with any card in any slot,it always changes.
I think somehow that that is the important part ?
All cards and risers work fine and have been checked in different slots,different risers,individually,
in groups and any combination you can think of.
All the info on here i can find i have followed.
So that's 4 gpu with claymore and sgminer,
and 5 with ethminer.
This is my first build and i have really enjoyed it so far,im looking forward to making more hopefully.
but i have now been banging my head against a brick wall for 2 weeks now(starting to make a mess)
Anyway i hope someone here has a clue for me.
Cheers !
|
|
|
|
Hello,
I am using Ethos and would like to run claymore with 6 gpu
hope someone could point me in the right direction here (please !)
You have to believe me here when i say that i have tried absolutley everything
i have read here but i just cannot get 6 gpu working with this motherboard.
With Claymore each gpu is at least 2 mh/s faster
With ethminer i can run 5 stable(3 days)
with both sgminer and claymore's the 6 gpu will start up and hash at 27 or so and the cut down to 4
after 1 or 2 minutes.
With sgminer it also does me the courtesy of telling me that the 2 gpu are sick then dead.
This can be with any card in any slot,it always changes.
I think somehow that that is the important part ?
All cards and risers work fine and have been checked in different slots,different risers,individually,
in groups and any combination you can think of.
All the info on here i can find i have followed.
So that's 4 gpu with claymore and sgminer,
and 5 with ethminer.
This is my first build and i have really enjoyed it so far,im looking forward to making more hopefully.
but i have now been banging my head against a brick wall for 2 weeks now(starting to make a mess)
Anyway i hope someone here has a clue for me.
Cheers
Provide more information about your setup: makes, models, versions, parameters, screenshots, troubleshooting steps taken... Sorry i forgot to post this bit: Operating system:Ethos mobo:Z170A GAMING PRO CARBON (MS-7A12) ram:4g Intel(R) Celeron(R) CPU G3900 @ 2.80GHz drive_name: KINGSTON SV300S37A120G GPU: 6x XFX rx480 8g one of which is the gtr black editition. PSU: Corsair hx1200i |
|
|
|
Hello,
I am using Ethos and would like to run claymore with 6 gpu
hope someone could point me in th right direction here (please !)
You have to believe me here when i say that i have tried absolutley everything
i have read here but i just cannot get 6 gpu working with this motherboard.
With Claymore each gpu is at least 2 mh/s faster
With ethminer i can run 5 stable(3 days)
with both sgminer and claymore's the 6 gpu will start up and hash at 27 or so and the cut down to 4
after 1 or 2 minutes.
With sgminer it also does me the courtesy of telling me that the 2 gpu are sick then dead.
This can be with any card in any slot,it always changes.
I think somehow that that is the important part ?
All cards and risers work fine and have been checked in different slots,different risers,individually,
in groups and any combination you can think of.
All the info on here i can find i have followed.
So that's 4 gpu with claymore and sgminer,
and 5 with ethminer.
This is my first build and i have really enjoyed it so far,im looking forward to making more hopefully.
but i have now been banging my head against a brick wall for 2 weeks now(starting to make a mess)
Anyway i hope someone here has a clue for me.
Cheers
Claymore runs them harder. Try reducing the memory frequency. Vlay Thanks, but i have had them at stock settings and it still showed all the same behaviour. |
|
|
|
|
Hello,
I am using Ethos and would like to run claymore with 6 gpu
hope someone could point me in th right direction here (please !)
You have to believe me here when i say that i have tried absolutley everything
i have read here but i just cannot get 6 gpu working with this motherboard.
With Claymore each gpu is at least 2 mh/s faster
With ethminer i can run 5 stable(3 days)
with both sgminer and claymore's the 6 gpu will start up and hash at 27 or so and the cut down to 4
after 1 or 2 minutes.
With sgminer it also does me the courtesy of telling me that the 2 gpu are sick then dead.
This can be with any card in any slot,it always changes.
I think somehow that that is the important part ?
All cards and risers work fine and have been checked in different slots,different risers,individually,
in groups and any combination you can think of.
All the info on here i can find i have followed.
So that's 4 gpu with claymore and sgminer,
and 5 with ethminer.
This is my first build and i have really enjoyed it so far,im looking forward to making more hopefully.
but i have now been banging my head against a brick wall for 2 weeks now(starting to make a mess)
Anyway i hope someone here has a clue for me.
Cheers
|
|
|
|
Hi, ive looked eveywhere and cant find an answer.
Could someone please tell me what ssssssssssssssssssssssssssssssssssss
mean when i look at the miner ?
Cheers
key is stuck on your keyboard Haha very funny, i did actually check that though, Anyone else ? |
|
|
|
Hi, ive looked eveywhere and cant find an answer.
Could someone please tell me what ssssssssssssssssssssssssssssssssssss
mean when i look at the miner ?
Cheers
Anyone Please ? |
|
|
|
|
Hi, ive looked eveywhere and cant find an answer.
Could someone please tell me what ssssssssssssssssssssssssssssssssssss
mean when i look at the miner ?
Cheers
|
|
|
|
|
