 Show Posts
|
|
Pages: [1] 2 3 »
|
Thanks!!! That does it! 31MHz like the rest. eric |
|
|
|
|
Hi,
I have a sapphire rx 580 nitro+ 8gb that only mine at 16MH.
I tried different bios and different setups but it stays the same.
Can someone help me?
Gr,
Eric
|
|
|
|
Hi,
Can I mix RX480 and R9 290?
I have a rig with 4X RX480 and 1X R9 290.
regards,
Eric
No, you cant. Different drivers (different OS version R and RX) @enricosofie Maeby this is a good opportunity for you to have 2 rigs RX480s for ETH rig, using smOS "RX" image and R9-290 for ZEC rig, using smOS "R" image Can I use the same account when I put 1 rig in ETH mining and 1 rig in ZEC mining? gr, Eric |
|
|
|
Hi,
I have a nice fast laptop with the latest intel and nvidia quadro M2000 (4GB)
I ll only getting 1.2Mh/s???
what's wrong?
regards,
eric
what coin do you mine? ETH only gives 1.2Mh/s ETH and DCR gives 1.2Mh/s ETH and 12Mh/s DCR quadro cards, if you have Windows and last drivers.... quadro card in control panel for gpu, has an option to use gpu for matematical operations, and grapichs operations. try to change this option. p.s. quadro 2000 (m)2000 is only for mobile, notebooks.... is not as new card as you may thing. I have the latest driver 382.05 but I can't find the setting that your mentioning? I see a setting "Optimize for Compute Performance" but that doesn't give better hashrates. eric |
|
|
|
Hi,
I have a nice fast laptop with the latest intel and nvidia quadro M2000 (4GB)
I ll only getting 1.2Mh/s???
what's wrong?
regards,
eric
what coin do you mine? ETH only gives 1.2Mh/s ETH and DCR gives 1.2Mh/s ETH and 12Mh/s DCR |
|
|
|
|
Hi,
I have a nice fast laptop with the latest intel and nvidia quadro M2000 (4GB)
I ll only getting 1.2Mh/s???
what's wrong?
regards,
eric
|
|
|
|
Hi,
I have a problem with a rig.
Yesterday I removed an older R9 card. Now there are only 4 x RX480s in the rig.
When I started the rig, it started-stoped-started-stoped-started but no screen, no beeps, nothing.
I removed all unnecessary things (so only cpu and mem is on the motherboard) and stil the same!
The mainboard is an Asrock btc pro.
CPU is an intel G1840
Ii tried a couple of different memory.
Power supply is an EVGA 1600 G2.
Any ideas?
regards,
eric
First I would reset the CMOS. i 've tried that! But no luck!!! Ok next I would try getting the board to boot to the bios.........nothing connected like you did before, except this time try only one stick of mem you dam sure is good. Try it in each slot to see if you can get to the bios. Don't forget to disconnect the drive your OS is on. I did all that. just motherboard, CPU and 1 stick of good mem. (no HD, no GPU, no nothing...) Still the same! eric tried with other ram. Still nothing. Next........I'd order a new mobo. There is a chance your cpu went bad, but the odds against that are pretty high. You could also double check each of the power cables and PSU.....but it is likely a mobo gone bad on you. this is also possible yes... Just disconnected and cleaned the motherboard and connected the PSU to the motherboard. I got back in the bios! Changed the bios a bit (disable sound) And when rebooting, I get the same problem!!!  what gpu are you using? on board, or gpu in pcie? I tried the on board gpu, an RX480 and an old nvidia. All the same. |
|
|
|
Hi,
I have a problem with a rig.
Yesterday I removed an older R9 card. Now there are only 4 x RX480s in the rig. (to change to simplemining!!!)
When I then started the rig, it started-stoped-started-stoped-started but no screen, no beeps, nothing.
I removed all unnecessary things (so only cpu and mem is on the motherboard) and stil the same!
The mainboard is an Asrock btc pro.
CPU is an intel G1840
Ii tried a couple of different memory.
Power supply is an EVGA 1600 G2.
Any ideas?
regards,
eric
did u checked all cables on the board ... probably re-plug them? including the molex power supply for pci-e? Yes, i did. Now there is just the power supply connected to the motherboard, CPU and RAM. No GPU, no HD or other devices. regards, eric bios working? Just disconnected and cleaned (air) the motherboard and connected the PSU to the motherboard. I got back in the bios! Changed the bios a bit (disable sound) And when rebooting, I get the same problem!!! |
|
|
|
Hi,
I have a problem with a rig.
Yesterday I removed an older R9 card. Now there are only 4 x RX480s in the rig.
When I started the rig, it started-stoped-started-stoped-started but no screen, no beeps, nothing.
I removed all unnecessary things (so only cpu and mem is on the motherboard) and stil the same!
The mainboard is an Asrock btc pro.
CPU is an intel G1840
Ii tried a couple of different memory.
Power supply is an EVGA 1600 G2.
Any ideas?
regards,
eric
First I would reset the CMOS. i 've tried that! But no luck!!! Ok next I would try getting the board to boot to the bios.........nothing connected like you did before, except this time try only one stick of mem you dam sure is good. Try it in each slot to see if you can get to the bios. Don't forget to disconnect the drive your OS is on. I did all that. just motherboard, CPU and 1 stick of good mem. (no HD, no GPU, no nothing...) Still the same! eric tried with other ram. Still nothing. Next........I'd order a new mobo. There is a chance your cpu went bad, but the odds against that are pretty high. You could also double check each of the power cables and PSU.....but it is likely a mobo gone bad on you. this is also possible yes... Just disconnected and cleaned the motherboard and connected the PSU to the motherboard. I got back in the bios! Changed the bios a bit (disable sound) And when rebooting, I get the same problem!!! |
|
|
|
Hi,
I have a problem with a rig.
Yesterday I removed an older R9 card. Now there are only 4 x RX480s in the rig.
When I started the rig, it started-stoped-started-stoped-started but no screen, no beeps, nothing.
I removed all unnecessary things (so only cpu and mem is on the motherboard) and stil the same!
The mainboard is an Asrock btc pro.
CPU is an intel G1840
Ii tried a couple of different memory.
Power supply is an EVGA 1600 G2.
Any ideas?
regards,
eric
First I would reset the CMOS. i 've tried that! But no luck!!! Ok next I would try getting the board to boot to the bios.........nothing connected like you did before, except this time try only one stick of mem you dam sure is good. Try it in each slot to see if you can get to the bios. Don't forget to disconnect the drive your OS is on. I did all that. just motherboard, CPU and 1 stick of good mem. (no HD, no GPU, no nothing...) Still the same! eric tried with other ram. Still nothing. |
|
|
|
Hi,
I have a problem with a rig.
Yesterday I removed an older R9 card. Now there are only 4 x RX480s in the rig. (to change to simplemining!!!)
When I then started the rig, it started-stoped-started-stoped-started but no screen, no beeps, nothing.
I removed all unnecessary things (so only cpu and mem is on the motherboard) and stil the same!
The mainboard is an Asrock btc pro.
CPU is an intel G1840
Ii tried a couple of different memory.
Power supply is an EVGA 1600 G2.
Any ideas?
regards,
eric
did u checked all cables on the board ... probably re-plug them? including the molex power supply for pci-e? Yes, i did. Now there is just the power supply connected to the motherboard, CPU and RAM. No GPU, no HD or other devices. regards, eric |
|
|
|
Hi,
I have a problem with a rig.
Yesterday I removed an older R9 card. Now there are only 4 x RX480s in the rig.
When I started the rig, it started-stoped-started-stoped-started but no screen, no beeps, nothing.
I removed all unnecessary things (so only cpu and mem is on the motherboard) and stil the same!
The mainboard is an Asrock btc pro.
CPU is an intel G1840
Ii tried a couple of different memory.
Power supply is an EVGA 1600 G2.
Any ideas?
regards,
eric
First I would reset the CMOS. i 've tried that! But no luck!!! Ok next I would try getting the board to boot to the bios.........nothing connected like you did before, except this time try only one stick of mem you dam sure is good. Try it in each slot to see if you can get to the bios. Don't forget to disconnect the drive your OS is on. I did all that. just motherboard, CPU and 1 stick of good mem. (no HD, no GPU, no nothing...) Still the same! eric |
|
|
|
Hi,
I have a problem with a rig.
Yesterday I removed an older R9 card. Now there are only 4 x RX480s in the rig.
When I started the rig, it started-stoped-started-stoped-started but no screen, no beeps, nothing.
I removed all unnecessary things (so only cpu and mem is on the motherboard) and stil the same!
The mainboard is an Asrock btc pro.
CPU is an intel G1840
Ii tried a couple of different memory.
Power supply is an EVGA 1600 G2.
Any ideas?
regards,
eric
First I would reset the CMOS. i 've tried that! But no luck!!! |
|
|
|
|
Hi,
I have a problem with a rig.
Yesterday I removed an older R9 card. Now there are only 4 x RX480s in the rig. (to change to simplemining!!!)
When I then started the rig, it started-stoped-started-stoped-started but no screen, no beeps, nothing.
I removed all unnecessary things (so only cpu and mem is on the motherboard) and stil the same!
The mainboard is an Asrock btc pro.
CPU is an intel G1840
Ii tried a couple of different memory.
Power supply is an EVGA 1600 G2.
Any ideas?
regards,
eric
|
|
|
|
|
Hi,
I have a problem with a rig.
Yesterday I removed an older R9 card. Now there are only 4 x RX480s in the rig.
When I started the rig, it started-stoped-started-stoped-started but no screen, no beeps, nothing.
I removed all unnecessary things (so only cpu and mem is on the motherboard) and stil the same!
The mainboard is an Asrock btc pro.
CPU is an intel G1840
Ii tried a couple of different memory.
Power supply is an EVGA 1600 G2.
Any ideas?
regards,
eric
|
|
|
|
|
Hi,
I'm mining ETH only (claymore-eth-v9.4) at the moment.
When I try to mine in dual mode, the hashrate drops in a strange way.
I use these settings:
-wd 1 -r 1 -epool stratum+tcp://eth-eu.dwarfpool.com:8008 -ewal $walletETH/$rigName -esm 0 -epsw x -allpools 1 -mport -3333 -dpool stratum+tcp://dcr.suprnova.cc:3252 -dwal name.rigname -dpsw x
Rig 1: 4x RX470 (same cards) Asus STRIX-RX470-4G-GAMING
Rig 2: 6x RX480 (2 flavors of cards)
ETH only hashrates:
Rig 1: 107MH/s
Rig 2: 170MH/s
When I use ETH+DCR:
Rig 1: 50 to 60MH/s (18+18+9+13) and 1100MH/s
Rig 2: 160MH/s and 4750MH/s
So, rig 2 is stable, but rig 1 does strange things!!!
How to fix this?
Themps are all below 65°C
regards,
Eric
|
|
|
|
Hi, Can I set 2 types of mining in one account? I can only set one type (ethereum or zcash?) regards, Eric Hi,
Can I mix RX480 and R9 290?
I have a rig with 4X RX480 and 1X R9 290.
regards,
Eric
No, you cant. Different drivers (different OS version R and RX) @enricosofie Maeby this is a good opportunity for you to have 2 rigs RX480s for ETH rig, using smOS "RX" image and R9-290 for ZEC rig, using smOS "R" image |
|
|
|
|
Hi,
Can I mix RX480 and R9 290?
I have a rig with 4X RX480 and 1X R9 290.
regards,
Eric
|
|
|
|
Hi,
I have 3 GPU's in a system.
ATIflash sees 3 GPU's but Claymore's ZCash AMD GPU Miner v12.4 (win) only uses 2 GPU's.
What am I doing wrong?
regards,
Eric
What are the 3 GPUs you are using? 3X Sapphire Radeon RX 480 Nitro+ 8G regards, Eric Oke. 3 GPU's are working. (Bios wasn't good) Now to get the 4 GPU working!!! OS is win10 64-bit I have a MSI H97M-G43 The first slot (16x) is working The second slot (1x) doesn't work!The third slot (1x) is working The 4th slot (16x) slot is working How can i get the second slot to work??? Any ideas?? Regards, Eric Have you tried swapping the risers to different ports on your motherboard? I had a similar issue where 1 card dropped out and I just moved it to a different slot on the board and it started working again. Yes, I tried that. Swapped risers en swapped cards. |
|
|
|
Hi,
I have 3 GPU's in a system.
ATIflash sees 3 GPU's but Claymore's ZCash AMD GPU Miner v12.4 (win) only uses 2 GPU's.
What am I doing wrong?
regards,
Eric
What are the 3 GPUs you are using? 3X Sapphire Radeon RX 480 Nitro+ 8G regards, Eric Oke. 3 GPU's are working. (Bios wasn't good) Now to get the 4 GPU working!!! OS is win10 64-bit I have a MSI H97M-G43 The first slot (16x) is working The second slot (1x) doesn't work!The third slot (1x) is working The 4th slot (16x) slot is working How can i get the second slot to work??? Any ideas?? Regards, Eric |
|
|
|
|
