 Show Posts
|
|
Pages: [1] 2 3 4 »
|
|
The tool to check chip problems is the same for s9/s17 and so on?
|
|
|
|
|
I can have all of this, i have a good environment and a separated clean space in my farm, its just to know where to start and what to buy and so on.
|
|
|
|
|
1 - 220v
2 - we strip the 16" wire, wrap the 15amp power cable to it, weld with tin put a ribbon and a high fusion tape. (all of my machines are running with this electrical setup for one year)
3 - we try to make the avalons work in another environment (my office inside the building, in a 20 amp power plug) and same problem
4 - did you attach the psu's correctly to the units? Yes I think, i saw some videos (including one of yours) and i think that is correct, i can put some pictures of it if it helps
|
|
|
|
I don't understand your post.
Who used/tested the gear for a month?
A trusted friend. I think it's a power or PSU problem, the miner log is showing an error on the PSU. I think it's "Primary Over Current" and your vo (voltage out) looks to be 2.
How are you plugging them in (your infrastructure)?
I have a trifasical transformer, then bifasical to 60amp circuit breakers with a 16mm each wire and i weld 7 15amp cables and the machines (I use 7 s9 or 4 t17 in this setup) . I plugged then close to my s9s/t17s/T2T with 15 amp cables and tryed in my office inside the farm witch is another setup and the problem is the same. |
|
|
|
I need some help Contacted the support yet and they barely answer my questions I have 4 1041 with separated psus, all of then was tested/used for a month before with no issues. When they arrive a reseted to factory (1 min pressed the func button) and put my pool/user data and IP settings They're not hashing, no one of the 4 machines (in the overview theres a message Hashboard: 0), i tested another fw, check the connections, change the pool and nothing. The worker appears on slushpool that means no network problem, but the hash is 0. Below I put some screenshots with the problems, if someone have a tip or need more info i can provide. The support says that is a short circuit on the miner. I post some pics on imgur https://imgur.com/a/JGZZQAP |
|
|
|
|
Nope, a friend contact the support.
To restart to factory you have to power off, and power on with func pressed for 1 min. Then wait a couple seconds and power off/on and voilá.
|
|
|
|
|
Someone help me
How to go back to factory and dhcp settings? I push the rst button for 15 seconds and 25 seconds, and nothing..
|
|
|
|
How do i default all settings on T1 using reset button?
it wont reset, and i cant ping it because of an ip conflict.
push the ip set button for 10 seconds |
|
|
|
I will try turning off for 2 hours.
What firmware are you running I am running t1_20180511_034450.swu
its one of the only ones so far that actually shows 3 boards most of the rest so far just show 2.
tested with 2 machines so far for 24h and 2 for 3 hashboards come back to life!! thanks for the tip. |
|
|
|
|
I hard reset some machines via software and two boards back to life for a couple hours and then shut down, so i think its dead tho.
|
|
|
|
|
Im using the last one provided with the auto update. but already tested this boards on braiins and no sucess.
|
|
|
|
|
You already try to clean the machines? or power off for a couple of hours and start again?
I have 75 T1s from may/2018, only last week i have 8 dead hashboards, in a total of 12 total (since the month that i receive) Im mining at slush too but i dont think this is the problem.
|
|
|
|
Fri Jun 28 22:56:37 2019 daemon.err cgminer[1373]: [2019-06-28 22:56:37.619] chain 5: no sensors found!
Fri Jun 28 22:56:37 2019 daemon.err cgminer[1373]: [2019-06-28 22:56:37.620] chain 5: running i2c scan, this may take up to 30 minutes per chain
Fri Jun 28 22:56:37 2019 daemon.err cgminer[1373]: [2019-06-28 22:56:37.620] (if you don't want to do this, use --no-sensor-scan parameter)
can anyone help me where to do this ( --no-sensor-scan)? im really noob. |
|
|
|
|
Theres a way to make braiins auto restart the asic when not hashing?
|
|
|
|
The error you posted it's trying to upload the s9 firmware, use the t1 firmware instead.
LOL, im so dumb, thanks for the advice, now seems that it goes, is "Restarting" for a couple minutes. |
|
|
|
Im having this trouble when putting de fw in a Dragonmint T1 with G19 board on windows. Preparing system for backup...
Traceback (most recent call last):
File "upgrade2bos.py", line 185, in <module>
main(args)
File "upgrade2bos.py", line 90, in main
if not platform.backup_firmware(args, ssh, backup_dir, mac):
File "G:\braiins\braiins-os_am1-s9_ssh_2019-02-21-0-572dd48c\upgrade\platform.py", line 77, in backup_firmware
ssh.run('/etc/init.d/bmminer.sh', 'stop')
File "G:\braiins\braiins-os_am1-s9_ssh_2019-02-21-0-572dd48c\upgrade\ssh.py", line 228, in run
self._check_exit_status(cmd, stdout, stderr)
File "G:\braiins\braiins-os_am1-s9_ssh_2019-02-21-0-572dd48c\upgrade\ssh.py", line 159, in _check_exit_status
raise CalledProcessError(returncode, cmd, stdout, stderr)
subprocess.CalledProcessError: Command '/etc/init.d/bmminer.sh stop' returned non-zero exit status 127. Then nothing happened and the fw keeps the same, someone can help me? |
|
|
|
|
This thing can be putted on horizontal?
|
|
|
|
Someone help me with the api
i want to see my off workers as below and i have this api token (example) 932jd937fj3
{
username: "username",
btc: {
confirmed_reward: "0.00765122",
unconfirmed_reward: "0.00062272",
estimated_reward: "0.00006014",
send_threshold: "0.01000000",
hash_rate_unit: "Gh/s",
hash_rate_5m: 27978,
hash_rate_60m: 28191,
hash_rate_24h: 28357,
hash_rate_scoring: 28294,
low_workers: 0,
off_workers: 0,
ok_workers: 2,
dis_workers: 2,
}
}
Whats the url should i enter?
I solved, imported with excel. if someone needs help with that i can make a post on how to push slush data into it. |
|
|
|
|
