Show Posts
|
Pages: [1]
|
Make it possible for downloading to be able to select the version of the miner. Version 2.1.10 works much worse than 2.1.9.
|
|
|
Was the blown miner with a bloated pool covered? The fact that the pool steals so it does not go to the grandmother. And in general it would be a really good lesson if the miners left the pool. Maybe they would have been fooled then.
|
|
|
What's with the XZC pool? Half a day the farm was wasted. Do you have something to change for the better?
|
|
|
... ... ... he is 100% right btw, you really should mine something else with you 1070. If you had 1080Tis I would almost agree with you
Zcoin profits are decent on a 1070. What alternatives are there?, or do you mean obscure things like goByte? As they say a lot for this there are reasons. That ping is to blame, then the miner himself is some kind of garbage. But the fact that the hash of the network itself plus a minus does not particularly fluctuate, but the payroll sharply goes down. And in conclusion I will say. Almost all blocks on zcoin catch this pool. And they rub all nonsense here. The conclusion suggests only one.
|
|
|
so i have read people wanna to leave MPH and some people showing some tests. Is this pool ligit or are people running for the hills?
I raised my power two days ago on 19 MH/s. Instead of increasing my profits, I get less coins than before. The whole network did not grow in capacity. So it is not necessary to say here that the coin network itself is to blame for this. So the pool steals and does not act honestly. This is the coin of XZC. for me too with zcoin. From the 9th of December the number of coins mined fell about 20-25%. 2 farms (~173mh\s and ~75mh\s) in different locations, the result is the same, the loss of 20-25% of coins Please don't assume it's stealing. There are many reasons for losses in real pools. And what are the reasons? Can please please detail. The complexity of the network did not grow, and even subsided a little.
|
|
|
so i have read people wanna to leave MPH and some people showing some tests. Is this pool ligit or are people running for the hills?
I raised my power two days ago on 19 MH/s. Instead of increasing my profits, I get less coins than before. The whole network did not grow in capacity. So it is not necessary to say here that the coin network itself is to blame for this. So the pool steals and does not act honestly. This is the coin of XZC.
|
|
|
In general, the pool is unclean. In particular, this applies to ZCOin. Where does it go about 20 percent? Can suffice to HUMBLE UP. You have not 0,9 percent, but 29 percent.
Is this factual or timing of pool showing hash rate? The hash is about 65.8-68MH / s. I'm on the pool for two months.
|
|
|
In general, the pool is unclean. In particular, this applies to ZCOin. Where does it go about 20 percent? Can suffice to HUMBLE UP. You have not 0,9 percent, but 29 percent.
|
|
|
Good afternoon! Why is the zcoin coin paid on your pool with such a delay? Can you find out why this is so? I apologize for my English.
|
|
|
Good afternoon! The dbix address pool is 0xa33001b8edf0ffb1bc925b40c1379d5fa48850ae. There are no payments. Thank you in advance. I apologize for the bad english.
|
|
|
Well, I was able to make zcash mining work at 210 h/s for RX 480 8Gb at stock. Eth makes cry me hardware errors still. There were a lot of warnings during compiling mostly about version 5.5.4 -> 5.5.5 change But it looks like I have to dive into the details.
There's supposed to be a few HW errors, maybe one or two per minute on Eth. Tell me please! Will there be a version for Windows? Thank you very much in advance.
|
|
|
Hey guys! SGMiner-GM 5.5.5 is out. Check the main post, otherwise, here is the release page. Let me know if there are any bugs. We know XMR algorithm switching is a bit funky, we're working with a driver limitation and all we can do is patch it until AMD gets their act together and fixes some things. Enjoy! A version for Windows will be?
|
|
|
You can particularly see your file. Do not send the first page only.
Who? Me? What do you want to see? edit: 1100/1500 -100mV (~1.07V). gpu0 elpida 1250 strap gpu1 hynix 1125 strap gpu2 elpida 1250 strap I would like to see himself config.conf file
|
|
|
How do you mine xmr? Here only I get W / H error
Something wrong with your hardware/ launch configuration. I do not know, maybe it could be Can you tell me how you wrote the commands in the miner? Read that first post in this thread, set everything to default. If you still get only h/w errors there must be something wrong with your h/w. All other programs normally run only the one that fails I'm using this line sgminer -k ethash -o eth.pool.minergate.com:45791 -u you_email -p x You need xmr.conf file, copy/paste below (from op), edit to your needs. Then launch with command sgminer -c xmr.conf { "pools": [ { "name": "MoneroPool", "url": "stratum+tcp://mine.moneropool.com:3333", "user": "x", "pass": "x", "priority": "0", "profile": "xmr" } ], "profiles": [ { "name": "xmr", "algorithm": "cryptonight", "rawintensity": "1024", "worksize": "8", "gpu-engine": "1000,1050,1050,1000", "gpu-memclock": "1500,500,1500,1500", "gpu-powertune": "20,50,50,50", "gpu-threads": "1", "gpu-fan": "100" } ], "default-profile": "xmr", "no-submit-stale": true, "no-extranonce": true } You can particularly see your file. Do not send the first page only.
|
|
|
|