 Show Posts
|
|
Pages: [1] 2 »
|
|
Congratulations for the good results! What about 1070/1070Ti? Will there be a new pill available in near future?
|
|
|
|
If I put //localhost:42000 in browser it show the statistics in browser but how to access that from internet?
You would need to forward port 42000 to your machine internal IP on your router, which is a bad idea since it's accessible by anyone and it opens up your machine to attacks. A better option would be to run a VPN server on your machine so you can connect to it from the internet or use RDP software like TeamViewer. Thanks I already replaced TeamViewer with VNC because the last is considerably lighter. |
|
|
|
|
If I put //localhost:42000 in browser it show the statistics in browser but how to access that from internet?
|
|
|
|
Hi, I have 2 x V56 and I went exact gandalph300 tutorial:
Core Frequency: -4%
Memory Clock: 945 MHz
Power Limit: -10%
Stock BIOS
And that gives me about 1940H/s per card and that's awesome!
But I got ~80watts@wall when idle and ~420watts@wall when mining. It seems these values are high.
What should I do to lower my watt usage?
How did you get 1940H/s with stock bios and without reg mod? Mine 56 is flashed and can't do more than 1200 because it's not stable after reg modding. |
|
|
|
Hello guys, Im running vega56 on latest amd driver 17.10.3. The hashrate in eth is good - about 43mh but i could not reach more than 1100h/s in xmr...
I also noticed that GPU Workload feature is missing in radeon settings. Then how can I enable this option?
Hi, this option is not supported for vegas. Not yet. I did not find this option too. Thanks! I installed blockchain driver aug23. When I started the cast miner the speed was 2000h/s for 5 seconds then suddenly the driver crashed. In the next attempt miner gave "[Suspicious link removed]pute driver not detected!" and the speed almost 1/2 less. I also receive this error when I enable HBCC. Another issue - core voltage is too high 1.05 - 1.1v. In eth mining I can reduce it to 0.825-0.86mv... |
|
|
|
|
Hello guys, Im running vega56 on latest amd driver 17.10.3. The hashrate in eth is good - about 43mh but i could not reach more than 1100h/s in xmr...
I also noticed that GPU Workload feature is missing in radeon settings. Then how can I enable this option?
|
|
|
|
|
Hi guys. The setup is following:
On the 1st rig are running 470/480 gpu using 16.11.5 driver, all bioses are modded and working without any problem.
On the 2nd is still only one 570 driven by 17.4.4 which is patched in order to accept modified bios.
The issue is I can't install all cards in only one rig and consequently the consumed power is more.
17.4.4 doesn't recognize the 4xx cards. And the vise versa is valid i.e. 16.11 or 16.12 are not suitable for 570 (the display driver is missing when you run the setup.exe).
Any ideas? Thank you for your help.
|
|
|
|
for now 1080ti can roin in two months, i don't know the amd situation but it's not better than nvidia, nvidia is very good at skein and sia, but amd can dual mine sia with ETH, i still think nvidia is better, the 1080ti will hold a good value for gamers, they like strong gpu
1080ti can do the roi in 2 months?? If was like this it has to mine for $400+ per month  |
|
|
|
|
In this case I think its better to use the warranty. Would be incorrect on your side to sell card which is not working on the buyer's mobo.
|
|
|
|
|
You can flash it at your own risk or leave it as it is. I'm not responsible for the consequences.
|
|
|
|
Then you can try to flash the card using bios from techpowerup database. Open it with bios editor and check the values. If the size is 256kb open it with atiwinflash then save.
Hi Red when i open bios of techpowerup database(256kb) i reiceve this message :  what can i do? Load it in atiwinflash then save and check if the size is changed to 512. Better don't flash with this 256kb only. |
|
|
|
|
Then you can try to flash the card using bios from techpowerup database. Open it with bios editor and check the values. If the size is 256kb open it with atiwinflash then save.
|
|
|
|
|
I meaned what software you used for backup- atiflash or something else?
|
|
|
|
Thanks for help spiz0r, i cant't understand if it is a sort of brick, only the asus detect the card and only if connected to pcie, asrock z97 anniversary and asrock h81m btc doesn't detect it and how possible the problem remain also after i restore the original bios backup of 470  How did you make the backup? And what is its size in kb? |
|
|
|
|
Hello people, how can I fix this error by wolf-xmr-miner-v0.4 :"Error parsing version string from clGetDeviceInfo. This should never happen." ?
I use 1150 platform with win10 pro & crimson 16.11.5. When start the miner in the 1155 - no problem. But with 1150 system I always get the above error. If i disable the internal gpu the error is "Error -1 when calling clGetDeviceIDs for number of devices."
|
|
|
|
Better release it when the zec price start to go up |
|
|
|
use msi afterburn. i've been able to lower the 290x to 125 watts average as per gpu-z. In my case i'm more worried on the fan noise so this voltage lowering brought the temp to the mid 60s and the fan to 60%, this while maintaining the sols at 337 to 347
What you see on gpuz is not the total power consumption of the card. 125w for the gpu only is possible but with the rest of power components on the pcb the real consumption is much more(about 200w). Check with wattmeter if you don't believe. |
|
|
|
it fucks all the limits
Confirmed but there must be some solution. Like waterblock instead of fan after all  |
|
|
|
I got this same error.
It was because when I C&P the address into the batch file it removed the space between the address and -p x
Just check those two addr: 4GdoN7NCTi8a5gZug7PrwZNKjvHFmKeV11L6pNJPgj5QNEHsN6eeX3DaAQFwZ1ufD4LYCZKArktt113 W7QjWvQ7CWFNeDcndLq3GwnXRLM 46evMe84XVyeAD9XsQ3G93WtcVQeLpC4P4UKEPMwEhdYRwAo8KKtTrf5DQMitTK8TnWo7EMUxvXjXjW djutnMbf823AbDkR The longer is from Kraken and the 2nd is from mymonero.com. The space could be a problem as you said but in my case I think the address is strange. |
|
|
|
While using this miner I noticed the fan speed of the main card(rx 470) suddenly jumped to 100%! WTF??
I'd say its a driver bug. however I have it only in sgminer. I use mostly 16.9.2 and never seen it on claymore, but on sgminer I get it all the time on all the rigs I tested EDIT: some weird combination of XMR algo code and drivers In addition to this problem is I'm not able to fix the crazy fan at normal speed unless I reset the system. And after one amd driver crash and and reboot the driver has changed from 16.10.3 to 16.6.. but this is another issue. same here, only the reboot solves this crazy run... it shows over 5000RPM on refs. Have you tried to set fan rpm max limit with wattool or wattman before it rise to 100% rpm? |
|
|
|
|
