 Show Posts
|
|
Pages: [1] 2 »
|
I'm using the Radeon Blockchain Compute Driver Version 17.30.1029 for every card.
Well, this is exactly what I was suspecting. I was fairly clear about GGS supporting only Adrenalin 17.12.2 and 18.1.1. There is not much I can do when you run GGS with a deprecated, unsupported driver. Maybe I should add a warning about unsupported drivers... Thanks I switched drivers didn't see that part about the driver compatibility and so far so good. Does the GGS overclock not work? I changed the clock speeds in the devices tab (under the appropriate algorithm) but nothing happens |
|
|
|
Whenever the pool goes down the miner will cause windows to freeze/crash... I have a really hard time getting back running after that as I keep getting a BSOD "Thread stuck in device driver" like 30 seconds after the desktop boots up with nothing running.. It was stable all day until my pool went down now I can't even get back into windows... might have to reformat again
This is no good... Which driver are you using with which card? I'm using the Radeon Blockchain Compute Driver Version 17.30.1029 for every card. Managed to get around the BSOD by going in safe mode and disabling overclocking on startup in Afterburner a 4x port multipler
Ah, an important detail! Thank you. I always wondered about those 4x port multipliers. Which algo are you using? Are other algos working at all? I've only tested Claymores ETH+DCR dual miner and Cryptonite and they were running stable until I started running GGS now the other miners aren't even stable anymore :/ is it possible that GGS damaged my hardware? I didn't press boost performance |
|
|
|
|
Whenever the pool goes down the miner will cause windows to freeze/crash... I have a really hard time getting back running after that as I keep getting a BSOD "Thread stuck in device driver" like 30 seconds after the desktop boots up with nothing running.. It was stable all day until my pool went down now I can't even get back into windows... might have to reformat again
|
|
|
|
Windows won't even boot up without freezing anymore this is the second time GGS made me have to reinstall windows. Original GG was way more stable
You can stop auto-start by holding a Shift key. Also, I am pretty sure you read a warning about modded BIOS. I would really like to help more, but there is only so much I can do with the limited information you gave me. I do have modded bios on my RX 470s (1500 straps) is that the problem for all the freezing? 1500 straps could be a real stretch, depending on how high the memory clock is, so I wouldn't rule them out as a cause of instability. By the way, you can pretty much achieve the same effect by copying only MC_SEQ_MISC1/3/8 from 1500 straps to the target straps and then applying nerdralph's strapmods (ACTRD=16, FAW=0, T32AW=0, TRRD=5). I have been scratching my head for the last few days in order to stabilize real-time memory timing mods and discovered a few new tricks here and there. Just reflashed the bios to original and still unstable my setup is 6x Rx 470 using a 4x port multiplier with an old dx7500 motherboard intel e8400 processor its a budget build but works fine with other miners like Claymore, just can't get it running stable on this :/. My other rig using a new motherboard and no port multiplier is running this stable |
|
|
|
Windows won't even boot up without freezing anymore this is the second time GGS made me have to reinstall windows. Original GG was way more stable
You can stop auto-start by holding a Shift key. Also, I am pretty sure you read a warning about modded BIOS. I would really like to help more, but there is only so much I can do with the limited information you gave me. I do have modded bios on my RX 470s (1500 straps) is that the problem for all the freezing? |
|
|
|
|
Windows won't even boot up without freezing anymore this is the second time GGS made me have to reinstall windows. Original GG was way more stable
|
|
|
|
|
Why this keep freezing my rig after like 30 minutes it doesn't even restart I have to manually reset the power supply to get it going again
|
|
|
|
|
@zawawa It is freezing my computer on one of my rigs that uses an old HP motherboard and a port multiplier but works on my newer rig can you fix please? Great miner btw
|
|
|
|
|
It's a motherboard/processor issue, I got around this by using a port multiplier on one of the x1 slots.
I would try messing around with BIOS first like disabling junk like onboard audio and change pci configurations.
|
|
|
|
Thanks its now working stable |
|
|
|
|
Works for like 2 minutes then it makes beeping noises and freezes..
Specs:
Windows 10
mixed AMD rig (290x/7950/480)
no overclock
|
|
|
|
|
Why is the wifi so unstable
|
|
|
|
 0.44 cent BTC transactions 1 hour confirmation, looks like BTC is back to being usable |
|
|
|
|
Is Bitcoin Private going to be given out to Bitcoin holders or Bitcoin Cash holders?
|
|
|
|
|
XRB will be the preferred p2p currency in the long term not BCH
|
|
|
|
|
The issue here is that essentially Bitcoin cash is just enabling cheap transactions until their pool of transactions also becomes to large - BUT - it’s good enough for now, which is a powerful thing in technology and often lets people select their preference so timing is important.
They seem to have drastically downplayed the effect of just increasing the block size
|
|
|
|
Segwit now active on BTC! Still 37k unconfirmed transactions though
I think SegWit is meant more for enabling the Lightning Network, than a standalone solution for Bitcoin scaling. Also meant to be a temporary scaling solution until LN which is still a long time away. So we're supposed to deal with these slow and expensive transactions until then? |
|
|
|
|
Segwit now active on BTC! Still 37k unconfirmed transactions though
|
|
|
|
People are saying it is taking a very long to transfer BCC. Has anybody transferred today? How long is it taking? What type of fees is being charged?
Just tried about 2 hours ago and it was confirmed in less than 10 mins, fast and cheap |
|
|
|
|
