 Show Posts
|
|
Pages: [1]
|
|
Ho investito anche io in Envion ma non mi è del tutto chiaro come e quando avverranno i payout. Saranno fatti in eth sul conto usato per comprare i token?
La data prevista del primo payout? In uno dei documenti mi pareva di aver letto 6 mesi dopo la chiusura della fiscalità o qualcosa del genere ma non trovo più il documento e non sono sicuro di aver capito bene.
|
|
|
|
...
To get back 1600h/s xmr stop your miner, go to radeon settins, gaming and move HBCC slider slightly, then hit apply.
Then run you miner again, here you go again ))
Need your kisses ))
Same results for me using HBCC, I got 1020H/s with vega 64 core 1150@900v and ram 1100@900v driver 17.9.1 (but with 17.8.2 was the same). I use intensity 1536 and worksize 16 and i tryed many value including 1500/8, 1000/16 1000/8 and many similiar. What's the trick? Blockchain drivers will do the trick. But it is difficult to downvolt with them ... Isn't blockchain driver only useful for ETH ? I though XMR was not concerned. ... I've same doubts, but i'll give it a try soon. Anyway, is it possible that HBCC gave different improvements depending on the system/ram used? I'm on a i5 2500k/ddr3 config... Still can't get what's the best instesity/worksize, could you share it please? |
|
|
|
I have two Vega 64 cards now, same settings same everything. One is capable of 1250 H/s on Monero, the second one can go to 1580 H/s o.O
Would you mind sharing your settings? After a reboot, I am not able to reproduce the 1580 H/s score  Both cards run between 1250 and 1280 H/s. Just standard Wattman settings, core as low as possible, mem to 1100, temp limit 71℃, -5% power. However, this is not enough to reduce the power draw at the wall. We need to give rednoW some motivation to share his guide with us. A kiss won't be enough I assume. To get back 1600h/s xmr stop your miner, go to radeon settins, gaming and move HBCC slider slightly, then hit apply. Then run you miner again, here you go again )) Need your kisses )) Same results for me using HBCC, I got 1020H/s with vega 64 core 1150@900v and ram 1100@900v driver 17.9.1 (but with 17.8.2 was the same). I use intensity 1536 and worksize 16 and i tryed many value including 1500/8, 1000/16 1000/8 and many similiar. What's the trick? |
|
|
|
So what is the verdict?
Continue using the robinh00d driver or install the official AMD beta blockchain driver?
Has anyone seen any speed difirence between the two?
Thanks
Tested in 2 rig, same speed for me. With AMD beta blockchain I can open wattman without crash (but voltage settings still doesn't work). |
|
|
|
Yes, Wattman works.
Are you sure? I can set the voltage with wattman, but it looks like a fake setting cause power consumption stay uge. I tried with 2 x RX 470 XFX, I'll test with 6 x mixed 480/470 rig soon. |
|
|
|
|
I've 2 of this:
Modded bios with 1500 timing
900mv/1050mhz core and 900mv/2000mhz ram
28.2Mh/s
900mv/1050mhz core and 910mv/1940mhz ram
26.4Mh/s
Claymore 9.3 -dcri 23
260W@wall for both, probably i could do better
EDIT: Both Elpida
|
|
|
|
My rig: 5 xfx 470, core 1100, memory 1975, 141mhs and 685 watts in the wall.  How you did the lower the voltage on xfx ? I can not control the voltage on my xfx`s i did try with wattol, afterburner, trixx... no one work for me  XFX cards are fucking terrible, and don't use the usual voltage controllers. These cards are actualy quite good price/performance/awalability ratio But is there ANY way to change voltage? Even bios or other ways? I think i can experiment now with bios to see if it works, but i want to see some other people experience first. I use wattman, can't you? Right now I'm 900mv/1050mhz core and 900mv/1980mhz ram => 28.8Mh/s and 125/130W@wall |
|
|
|
|
Hi Claymore,
it would be nice to have a shortcut key ("l"?) to switch the low intensity mode.
Thanks a lot.
|
|
|
|
|
