This might be a simple question and im just missing something really obvious.
I just started messing around with a moonlander2 using bfgminer on a raspberry pi, and I had everything running fine, but I powered down the raspberry pi just to adjust the power adapter. I turned it all back on, but now I'm having trouble figuring out how to get bfgminer set up again and running.

When I set it up, I followed these instructions, and everything was working fine
https://steemit.com/raspberry/@qctechno/howto-install-futurebit-moonlander-2-usb-scrypt-miner-with-raspberrypi-3

Thanks in advance for the help

As the title states, I just bought an Avalon6, but I can't get it to mine.  I have tried on both viabtc and nicehash.  Both pools have recognized it as a worker, but it will not actively mine.
Any thoughts?

Thanks

I thought I would try dual mining on ethos.  I had been doing ethereum without a problem, but thought I'd add siacoin and see how it'd work.
I checked on ethos and saw that the rig is actively mining both, and saw the hashrates of both.
However, when I go to nanopool I can see the current hashrate, but it does not show any "workers" down at the bottom.  Is that normal or am I doing something wrong?

Thanks for the help

Just came across https://hardwardia.com and I’m just curious if anyone else has used it.
I haven’t seen much on it

Thanks for the help

I have a 7 gpu rig and it keeps freezing after about 5-10 minutes. Originally it was running 24+ hours before it would freeze, then would run 6-8 hours and freeze, then 2-3 hours and now about 5-10 minutes.
The setup
(7) nvidia 1070 gtx 8gb (blowers)
Mb: asrock h110 pro btc+
8gb crucial ram
Intel celeron 2.8ghz
(2) evga g2 1000w psu
Ethos - usb boot

I had these set at
Globalminer claymore
Globalcore 1506
Globalmem 4608
Globalfan 85
Maxgputemp 85
Pool-USA.ethosdistro.com:5001
Pool-eu.ethosdistro.com:5001


I have tried lowering both core and mem, but am having them same problem. I also reset everything and took it back to default settings for ethos to see if I could baseline everything, but it’s still shutting down after 5 min or so.

Thanks in advance for the help

Just built a new rig (not first), but I’m having trouble with ethos. Normally ethos has been pretty straightforward but this time I’m having trouble getting it running.
Ethos runs fine without any gpu plugged in, then I will shut it down, plug in a single gpu, and reboot, it will start the miner but then it will instantly ramp up the fan really high and the monitor screen will shut down.
The monitor is plugged into the gpu and will not work with the dvi slot on the mb

biostar tb 250 btc pro
Nvidia 1070 founders edition
Psu: evga 1000w g3

Thanks for the help

I know ethos says it pays out .2 eth on 6 hour intervals, but I’m wondering is that based on the amount you mined on each rig, or if you have multiple rigs on the same network, will it compile all that together?
Hope that makes sense

Thanks

I set up a 12 GPU rig and after a few hours it will keep disconnecting, all GPUs will go to 0.00 and I will get there following error from the online monitoring
Rig has not reported in over 3 minutes

Rig Setup
Asrock H110 Pro BTC+
(2) 4gb Crucial
(12) EVGA Geforce GTX 1060 6gb
(2) EVGA 850 GQ
Cor 2000
Mem 4300
(Previous Cor 2138, Previous Members 4608 and I had the same problem)
Mining pool
pool-usa.ethosdistro.com:5001
pool-eu.ethosdistro.com:5001

I have built a few mining rigs before, but normally just in a pc tower and connected the gpus directly to the board.  I decided to build 6 gpu rig but am having problems.  Every time I plug in a gpu to one of the 1x slots, the rig won't boot.  If I unplug all the gpus in the single slots or if I plug a single gpu riser into the 16x slot, it will power on properly.

I have tried with 5 gpus hooked up and with only a single gpu, and the same problem.
All the Gpus are powered with the 6 or 8pin plus the powered usb riser.  I only have 2 risers connected tops to the sata cable.

Stats on rig
ethos - booted on ssd
Biostar tb85
4gb ram
evga 850gq psu
I have tried 2 different gpus powered with 1x to 16x powered risers - Asus Geforce gtx 1070 turbo 8gb and evga geforce gtx 1060 6gb.

Thanks in advance for the help