 Show Posts
|
|
Pages: [1]
|
|
The Coins Tab is not updating any coin rates info?
I have tried on v6.5.5 everything works fine if I reinstall.
After that if I upgrade to the newer version the coin data stops updating and it gets struck on the last values.
There are no new changes on my system, I have tried it on different systems but the newer versions the coin data does not update.
Older v6.5.5 everything works perfectly.
|
|
|
|
|
How to use Temperature Throttling?
I am trying to use
-tt 1 -tstop 68 -tstart 55 -tmax 63
Only the tstop and tstart work. How do I make throttle work on tmax 63 ?
Any help?
|
|
|
|
|
Can TRM be used for Conceal coin?
Anyone please help.
|
|
|
|
|
Having a lot of stability issues on RX 570.
Instead of getting stable around 8.9 MHz it fluctuates between 6 MHz to 10MHz. Is it supposed to be like this?
I have tried a lot of different overclocks and tried what has been mentioned on the first page, but still the fluctuations in the speed.
Any advice?
|
|
|
|
|
Are there any working Exchanges for TSF as of now ?
Even BiteBTC, Deposits are not enabled.....
|
|
|
|
|
Is it possible to set constant fan speed in BOS for S9, my fan just keeps on spinning up and down every few minutes?
Rest running very stable.
|
|
|
|
Yes the miner is working fine pool side. I am using a SDCard and did a fresh firmware and have tried two different cards but the same results, the old firmware works fine. Only thing is it is not showing the miner screen and it is saying Miner Status
API connection status: Not connected
|
|
|
|
|
The miner status is not visible........although the miner is working fine.
What can be done to resolve the following ?
Miner Status
API connection status: Not connected
|
|
|
|
I am getting the following errors while upgrading via ssh: opkg update
Downloading http://downloads.lede-project.org/releases/17.01.4/packages/arm_cortex-a9_neon/base/Packages.gz
Updated list of available packages in /var/opkg-lists/reboot_base
Downloading http://downloads.lede-project.org/releases/17.01.4/packages/arm_cortex-a9_neon/base/Packages.sig
Signature check passed.
Downloading http://downloads.lede-project.org/releases/17.01.4/packages/arm_cortex-a9_neon/luci/Packages.gz
Updated list of available packages in /var/opkg-lists/reboot_luci
Downloading http://downloads.lede-project.org/releases/17.01.4/packages/arm_cortex-a9_neon/luci/Packages.sig
Signature check passed.
Downloading http://downloads.lede-project.org/releases/17.01.4/packages/arm_cortex-a9_neon/packages/Packages.gz
Updated list of available packages in /var/opkg-lists/reboot_packages
Downloading http://downloads.lede-project.org/releases/17.01.4/packages/arm_cortex-a9_neon/packages/Packages.sig
Signature check passed.
Downloading http://downloads.lede-project.org/releases/17.01.4/packages/arm_cortex-a9_neon/routing/Packages.gz
Updated list of available packages in /var/opkg-lists/reboot_routing
Downloading http://downloads.lede-project.org/releases/17.01.4/packages/arm_cortex-a9_neon/routing/Packages.sig
Signature check passed.
Downloading http://downloads.lede-project.org/releases/17.01.4/packages/arm_cortex-a9_neon/telephony/Packages.gz
Updated list of available packages in /var/opkg-lists/reboot_telephony
Downloading http://downloads.lede-project.org/releases/17.01.4/packages/arm_cortex-a9_neon/telephony/Packages.sig
Signature check passed.
opkg install firmware
Unknown package 'firmware'.
Collected errors:
* opkg_install_cmd: Cannot install package firmware.
Not sure what is wrong? |
|
|
|
|
What are the steps for updating the firmware, I have tried updating via ssh and via software menu but to no success.
Or do we have to re-image the card again?
Thanks.
|
|
|
|
|
IS there a version 8 with autofan ?
|
|
|
|
|
Mobile wallet has stopped connecting............any news?
Even the website is not opening!!!
|
|
|
|
|
Not able to run on GeForce GTX 1060 6GB × 12
Running HiveOS 0.5-76 Nvidia Drivers : 390.59, is working perfectly fine on Ethminer and Claymore....
PhoenixMiner starts but mining does not start keeps on 0
Thanks.
|
|
|
|
|
I have tried the v6b..........the fans remain on 100% and dont auto increase or decrease.
Is there any way to enable autofan or fixed to a specific speed.
FAN PWM: 0
read_temp_func Done!
Thanks..
|
|
|
|
|
Not able to reduce the difficulty while using the sha256 algorithm, it is defaulting to 125000
c=xxx, d=4128 or d=16382 not working.......any ideas?
|
|
|
|
If someone could help I am not able to change the fan speeds at all. I have got a 13.5 T Antminer S9 and with the 650M Fixed Freq firmware my fans just keep on doing High and low every minute. I am trying to fix the fan speeds at 90% but the fans seem to be auto adjusting. Below is the content of my bmminer.conf "api-listen" : true,
"api-network" : true,
"api-groups" : "A:stats:pools:devs:summary:version",
"api-allow" : "A:0/0,W:*",
"bitmain-use-vil" : true,
"bitmain-fan-ctrl" : true,
"bitmain-fan-pwm" : "90",
"bitmain-freq" : "650",
"bitmain-voltage" : "0706",
"multi-version" : "1"
Thanks. |
|
|
|
|
Thanks a lot for this excellent work.
I live in an extremely hot area so for me reducing the heat is important and so I have tried the 840 and 820 version, somehow the 830 version is missing from the download folder.
I just want to run my antminers near the default speeds with reduced temperatures and less HW errors, please advise the best way.
On 840 with freq of 650 the temp are almost the same.
On 820 with 650 with speeds get reduced and HW errors start occurring.
Thanks.
|
|
|
|
|
