I have an S7 that tries to hash gets to 5 TH then gives red light starts beeping. Out of warranty. Please any ideas?
lower the freq by 1000 if 700 go to 600 650 go to 550 check temps check fan speeds Thanks for the quick response! 600 stops the beeping and red light but can only get 4 TH.. Tried 650 and 625 and no beeping but Red light flashing Still having this problem anybody know a solution please? |
|
|
|
I have an S7 that tries to hash gets to 5 TH then gives red light starts beeping. Out of warranty. Please any ideas?
Same problem here.... and no kernel-log... will tinker around and see what I can do. Annoying is the fact that Bitmain does not react to questions at all. A support ticket was deleted without any response... It runs at 4 TH/s for an hour or so then starts beeping after reducing to 600 frequency.. |
|
|
|
Reset and still only 4 TH..
I haven't really been following this conversation, but are you able to test out your PSU voltages at all? I was having issues with my S7 having a sporadic hashrate, and eventually I was able to determine that a faulty 12V rail on my PSU was the source of the problem. voltages are alright |
|
|
|
I have an S7 that tries to hash gets to 5 TH then gives red light starts beeping. Out of warranty. Please any ideas?
lower the freq by 1000 if 700 go to 600 650 go to 550 check temps check fan speeds Thanks for the quick response! 600 stops the beeping and red light but can only get 4 TH.. Tried 650 and 625 and no beeping but Red light flashing From this point I'd reset it. Reset and still only 4 TH.. |
|
|
|
I have an S7 that tries to hash gets to 5 TH then gives red light starts beeping. Out of warranty. Please any ideas?
lower the freq by 1000 if 700 go to 600 650 go to 550 check temps check fan speeds Thanks for the quick response! 600 stops the beeping and red light but can only get 4 TH.. Tried 650 and 625 and no beeping but Red light flashing |
|
|
|
|
I have an S7 that tries to hash gets to 5 TH then gives red light starts beeping. Out of warranty. Please any ideas?
|
|
|
|
Keep getting pool o slow/down or invalid error, please help?
.bat:
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_USE_SYNC_OBJECTS 1
sgminer -I 20
pause
spreadcoin.conf:
rpcuser=user
rpcpassword=pass
rpcallowip=127.0.0.1
rpcport=41677
port=41678
gen=0
server=1
gen=0 signifies the wallet to NOT generate coins ... solomining requires you generate coins within the wallet - so change that to gen=1 ... its been a while since ive mined spr - and it was usually spreadminer-spmod ( nvidia ) that i mined with ... i could never get the amd miner to compile and work ... so if there is any help current miners would give - that will help you a great deal ... lots of talented people in this thread ... #crysx Thanks I am using AMD cards tried gen=1 still same error |
|
|
|
|
Keep getting pool o slow/down or invalid error, please help?
.bat:
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_USE_SYNC_OBJECTS 1
sgminer -I 20
pause
spreadcoin.conf:
rpcuser=user
rpcpassword=pass
rpcallowip=127.0.0.1
rpcport=41677
port=41678
gen=0
server=1
|
|
|
|
|
How is Fai different than LBRY?
|
|
|
|
The fact that the Dev premined 99% of the coins, automatically converts them into a kind of "centralized bank". In fact, they openly recognized that if the FAIcoins go up too much, they will sell, and if it drops down, they will buy. Isnt that what the Banks/Governments usually do?
Note this, if the FAI coins reach $1 USD per coin, they will be billionaires, and a few users will get a few thousand and the majority almost nothing. Same old story of concentrated wealth by bankers at the spend of other people...
What if Satoshi Nakamoto would have premined 99% of the Bitcoins?
Bitcoins would have been a joke by now.
read .257 please read .257 please read .257 please What does that even mean |
|
|
|
So if I have a chaindata folder can I import that into another computer to see if there are coins on it?
also how to import an address from one computer to another?? |
|
|
|
|
So if I have a chaindata folder can I import that into another computer to see if there are coins on it?
|
|
|
|
if you are way off delete your chain and resync
window
go to %appdata%/expanse and delete chaindata
linux
rm -rf ~/.expanse/chaindata
Does that mean my coins are worthless though? if they are all your blocks then probably.  If I show a remote ip then I have peers? So I sync then close the genesis.bat then I start expanse and start mining but im alwayjs behind in blocks? You have to be connected to nodes while your wallet is running, if not, than you are not synced with network..... Enter "admin.peers" or "net "in console and find out If I show a remote Ip then I have a peer? |
|
|
|
if you are way off delete your chain and resync
window
go to %appdata%/expanse and delete chaindata
linux
rm -rf ~/.expanse/chaindata
Does that mean my coins are worthless though? if they are all your blocks then probably. So I sync then close the genesis.bat then I start expanse and start mining but im always behind in blocks? |
|
|
|
if you are way off delete your chain and resync
window
go to %appdata%/expanse and delete chaindata
linux
rm -rf ~/.expanse/chaindata
Does that mean my coins are worthless though? |
|
|
|
|
Fuck, block 2976 ughhhh do I need to change anything to mine on the pool
|
|
|
|
|
How to verify on the correct chain?
|
|
|
|
got null, how to add peers on windows?
the same place you just did admin.peers add some of the nodes from the OP Ok so if I had null prior to adding peers and I added nodes now, are the coins I have worthless? I still show around the same balance? Anybody know how to check testnet coins vs real? |
|
|
|
got null, how to add peers on windows?
the same place you just did admin.peers add some of the nodes from the OP Ok so if I had null prior to adding peers and I added nodes now, are the coins I have worthless? I still show around the same balance? |
|
|
|
|
got null, how to add peers on windows?
|
|
|
|
|
Show Posts
