r9 nano

[byteme007]

why motherboard doesnt see my card on pcie 1X ? used standard ribbon raiser

[BigBoom3599]

Try it without the raiser, if that doesnt work you may have a faulty motherboard or GPU

[byteme007]

its ok when its directly in 16x , but problem is when i try to move it to 1x pci e, does r9 nano works on ribbon raiser ? or ? special raiser ?

[Amph]

it's the motherboard then, what motherboard are you using?

i know for certain(because it's my motherboard for gaming) that the asrock extreme 4 z97 for example does not support gpu on the x1 slot or riser used for gpu, due to a pin issue on the slot x1

you need the asrock h81 pro btc or somethign else that is used for these things

[rx07]

R9 does not support pcie 1X.

It requires "PCI Express x16" slot.

[joblo]

why motherboard doesnt see my card on pcie 1X ? used standard ribbon raiser

Make sure you use a powered riser and check to see if you need to short out two
pins in the x1 slot to allow high power. Google it.

[byteme007]

mobo is z97 anniversary , i have tried on old p45 to jump it from 16x to 1x and it works fine with R7 240 but again R9 nano p45 doesnt see , and z97 doesnt see nothin (r9 nano and r7 240 )

[joblo]

mobo is z97 anniversary , i have tried on old p45 to jump it from 16x to 1x and it works fine with R7 240 but again R9 nano p45 doesnt see , and z97 doesnt see nothin (r9 nano and r7 240 )

The nano is new so it might need newer drivers. If the 240 doesn't work in the x16 slot without the riser it might
be a bad mobo. If it does work it's probably a bad riser.

[byteme007]

p45 - r7 on riser 1xpci e works
p45 - r9 nano on riser 1x pcie doesnt work

z97 anniversary- r7 on 1x doesnt work
z97- r9 nano on 1x doesnt work
z97- r9 nano 16x works

[joblo]

p45 - r7 on riser 1xpci e works
p45 - r9 nano on riser 1x pcie doesnt work

z97 anniversary- r7 on 1x doesnt work
z97- r9 nano on 1x doesnt work
z97- r9 nano 16x works

Do you have more than one riser? One of them is bad.

- the riser on the P45 with the 240 works
- the riser on the P45 with the nano doesn't work
- the riser on the Z97 doesn't work with either card
- the nano works on the Z97 works without a riser


 

[byteme007]

only one , im planning to buy sec card , so tried to make place for second , ill try today with other riser s mby usb will work

[NorthPixel]

R9 does not support pcie 1X.

It requires "PCI Express x16" slot.

Not true. I use the nano on the x1 slot without problem. For some motherboarads, you need to short the card presence pin.

[byteme007]

what mobo , and riser ? can u make pic pls ?

[Eliovp]

I use 6x nano on a H81 Pro BTC board, also got one with the B95 Anniversary board.

Works perfectly on those x1 slots.

I "had" a few furies as well, also with risers, also connected with risers to a x1 slot (MSI z97 Gaming 5 Board).

Dunno where all you guys find all those issues :p

Riser perhaps?

[byteme007]

nah i think its motherboard z97 , ill go on pro btc i try it with usb risers

[WarrEagle]

R9 does not support pcie 1X.

It requires "PCI Express x16" slot.

That is an outright lie. I run numerous R9-380's on 6 GPU Rigs. Speaking from experience not my a$$