robert_C (OP)
Newbie
 Offline
Activity: 1
Merit: 0
|
 |
June 18, 2016, 05:06:16 PM |
|
I do not know how to insert the screenshot here, so apologies. the overview shows:
Miner Type Antminer S7
Hostname antMiner
Model GNU/Linux
Hardware Version 0.0.0.0
Kernel Version Linux 3.8.13 #22 SMP Tue Dec 2 15:26:11 CST 2014
File System Version Mon May 23 15:57:10 CST 2016
Cgminer Version 4.8.0
Uptime 3:38
Load Average 0.06, 0.04, 0.04
Memory
Total Available 62172 kB / 251172 kB (25%)
Free 189000 kB / 251172 kB (75%)
Cached 0 kB / 251172 kB (0%)
Buffered 0 kB / 251172 kB (0%)
miner config:
stratum.antpool.com:3333
usrnamofaccount.1
stratum.antpool.com:443
usrnamofaccount.11
stratum.antpool.com:25
usrnamofaccount.111
miner status:
Summary
Elapsed GH/S(5s) GH/S(avg) FoundBlocks LocalWork Utility WU BestShare
3h24m7s 0.00 0.00 0 6,739 0.00 0.00 0
Pools
Pool URL User Status Diff GetWorks Discarded
0 stratum+tcp://stratum.antpool.com:3333 subaccountname.1 Alive 265 6677
1 stratum+tcp://stratum.antpool.com:443 subaccountname.11 Alive 1 0
2 stratum+tcp://stratum.antpool.com:25 subaccountname.111 Alive 3
everything else in pools section is 0's
Antminer
Chain# ASIC# Frequency Temp ASIC status
nothing is here. It is just blank
Fan# Fan1 Fan2 Fan3 Fan4 Fan5 Fan6
Speed (r/min) 0 0 0 0 0 0
network is DHCP. I did not change it to static.
Frequency is set to 700
I dont know why it is not hashing. This is my 1st miner and was a test before I buy more. Any assistance would be greatly appreciated.
|
|
|
|
|
|
|
|
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
DarkStarPDX
Newbie
Offline
Activity: 7
Merit: 0
|
 |
June 18, 2016, 09:53:37 PM |
|
What is your power supply configuration? It sounds like your controller board is being powered properly, but maybe your ASIC blades aren't for some reason.
|
|
|
|
|
|
gt_addict
|
|
June 18, 2016, 10:29:06 PM |
|
As said above. Check all connections and make sure everything is getting power properly. Try switching pci cables around to see if something is wrong with one of them.
|
**SUPPORT SIDEHACK** Miner Development Donations to: 1BURGERAXHH6Yi6LRybRJK7ybEm5m5HwTr
Donations/Tips to:- 1GTADDicTXD1uachKKgW24DZDxDGhSMdRa
Join Bitconnect: https://bitconnect.co/?ref=gtaddict
|
|
|
robertroberrt
Newbie
Offline
Activity: 3
Merit: 0
|
|
June 19, 2016, 02:09:22 PM
Last edit: January 23, 2018, 07:48:30 PM by frodocooper |
|
sorry had to change username. I have the Bitmain PSU, I have swapped the cables on the PSD and the others just to check. The fans is running and everything seems to work except it doesnt hash. I have also reloaded the latest firmware and rebooted. The kernel log shows some errors and the last is "FPGA don't code" I am not familiar at all with Linux. Below is the log: [ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.8.13 (xxl@armdev01) (gcc version 4.7.4 20130626 (prerelease) (Linaro GCC 4.7-2013.07) ) #22 SMP Tue Dec 2 15:26:11 CST 2014
[ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=50c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: Generic AM33XX (Flattened Device Tree), model: TI AM335x BeagleBone
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] On node 0 totalpages: 65280
[ 0.000000] free_area_init_node: node 0, pgdat c06cb100, node_mem_map c0726000
[ 0.000000] Normal zone: 512 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 64768 pages, LIFO batch:15
[ 0.000000] AM335X ES1.0 (neon )
[ 0.000000] PERCPU: Embedded 8 pages/cpu @c0934000 s9408 r8192 d15168 u32768
[ 0.000000] pcpu-alloc: s9408 r8192 d15168 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64768
[ 0.000000] Kernel command line: console=ttyO0,115200n8 init=/sbin/init
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] allocated 524288 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Memory: 255MB = 255MB total
[ 0.000000] Memory: 236120k/236120k available, 26024k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf800000 - 0xbfe00000 ( 6 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0612cf0 (6188 kB)
[ 0.000000] .init : 0xc0613000 - 0xc06554c0 ( 266 kB)
[ 0.000000] .data : 0xc0656000 - 0xc06cc020 ( 473 kB)
[ 0.000000] .bss : 0xc06cc020 - 0xc0725e3c ( 360 kB)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts
[ 0.000000] Total of 128 interrupts on 1 active controller
[ 0.000000] OMAP clockevent source: GPTIMER1 at 24000000 Hz
[ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[ 0.000000] OMAP clocksource: GPTIMER2 at 24000000 Hz
[ 0.000000] Console: colour dummy device 80x30
[ 0.000355] Calibrating delay loop... 545.07 BogoMIPS (lpj=531968)
[ 0.015404] pid_max: default: 32768 minimum: 301
[ 0.015634] Security Framework initialized
[ 0.015729] Mount-cache hash table entries: 512
[ 0.025657] Initializing cgroup subsys cpuacct
[ 0.025691] Initializing cgroup subsys memory
[ 0.025756] Initializing cgroup subsys blkio
[ 0.025901] CPU: Testing write buffer coherency: ok
[ 0.026440] CPU0: thread -1, cpu 0, socket -1, mpidr 0
[ 0.026517] Setting up static identity map for 0x8038c820 - 0x8038c86c
[ 0.027910] Brought up 1 CPUs
[ 0.027932] SMP: Total of 1 processors activated (545.07 BogoMIPS).
[ 0.029228] devtmpfs: initialized
[ 0.093773] pinctrl core: initialized pinctrl subsystem
[ 0.093989] rstctl core: initialized rstctl subsystem
[ 0.094488] regulator-dummy: no parameters
[ 0.095002] NET: Registered protocol family 16
[ 0.095773] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.105563] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568
[ 0.106333] platform 49000000.edma: alias fck already exists
[ 0.106366] platform 49000000.edma: alias fck already exists
[ 0.106394] platform 49000000.edma: alias fck already exists
[ 0.107601] gpiochip_add: registered GPIOs 0 to 31 on device: gpio
[ 0.107783] OMAP GPIO hardware version 0.1
[ 0.109121] gpiochip_add: registered GPIOs 32 to 63 on device: gpio
[ 0.110440] gpiochip_add: registered GPIOs 64 to 95 on device: gpio
[ 0.111890] gpiochip_add: registered GPIOs 96 to 127 on device: gpio
[ 0.112419] of_get_named_gpio_flags exited with status 52
[ 0.112450] gpio-rctrl rstctl.3: loaded OK
[ 0.117248] omap-gpmc 50000000.gpmc: GPMC revision 6.0
[ 0.120520] hw-breakpoint: debug architecture 0x4 unsupported.
[ 0.122740] cpsw.0: No hwaddr in dt. Using 88:c2:55:84:d8:0d from efuse
[ 0.122772] cpsw.1: No hwaddr in dt. Using 88:c2:55:84:d8:0f from efuse
[ 0.138292] bio: create slab <bio-0> at 0
[ 0.150472] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver
[ 0.150707] of_get_named_gpio_flags: can't parse gpios property
[ 0.150921] vmmcsd_fixed: 3300 mV
[ 0.153990] SCSI subsystem initialized
[ 0.154470] usbcore: registered new interface driver usbfs
[ 0.154603] usbcore: registered new interface driver hub
[ 0.154876] usbcore: registered new device driver usb
[ 0.156927] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz
[ 0.158455] input: tps65217_pwr_but as /devices/ocp.2/44e0b000.i2c/i2c-0/0-0024/input/input0
[ 0.160192] DCDC1: at 1500 mV
[ 0.161336] vdd_mpu: 925 <--> 1325 mV at 1325 mV
[ 0.162526] vdd_core: 925 <--> 1150 mV at 1100 mV
[ 0.163627] LDO1: at 1800 mV
[ 0.164762] LDO2: at 3300 mV
[ 0.166695] LDO3: 1800 mV
[ 0.167852] LDO4: at 3300 mV
[ 0.168841] tps65217 0-0024: TPS65217 ID 0xe version 1.2
[ 0.169525] omap_i2c 44e0b000.i2c: unable to select pin group
[ 0.170312] omap_i2c 4819c000.i2c: bus 1 rev0.11 at 100 kHz
[ 0.172642] omap_i2c 4819c000.i2c: unable to select pin group
[ 0.172882] media: Linux media interface: v0.10
[ 0.172986] Linux video capture interface: v2.00
[ 0.173109] pps_core: LinuxPPS API ver. 1 registered
[ 0.173126] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.174000] Advanced Linux Sound Architecture Driver Initialized.
[ 0.175154] Switching to clocksource gp_timer
[ 0.193395] NET: Registered protocol family 2
[ 0.194399] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.194487] TCP bind hash table entries: 2048 (order: 3, 40960 bytes)
[ 0.194578] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.194671] TCP: reno registered
[ 0.194698] UDP hash table entries: 256 (order: 1, 12288 bytes)
[ 0.194745] UDP-Lite hash table entries: 256 (order: 1, 12288 bytes)
[ 0.195223] NET: Registered protocol family 1
[ 0.195791] RPC: Registered named UNIX socket transport module.
[ 0.195813] RPC: Registered udp transport module.
[ 0.195827] RPC: Registered tcp transport module.
[ 0.195841] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.196212] Trying to unpack rootfs image as initramfs...
[ 2.123239] Freeing initrd memory: 14788K
[ 2.123909] CPU PMU: probing PMU on CPU 0
[ 2.123942] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available
[ 2.124549] omap2_mbox_probe: platform not supported
[ 2.128434] VFS: Disk quotas dquot_6.5.2
[ 2.128674] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 2.129969] NFS: Registering the id_resolver key type
[ 2.130061] Key type id_resolver registered
[ 2.130079] Key type id_legacy registered
[ 2.130146] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 2.130671] msgmni has been set to 490
[ 2.133441] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 2.133467] io scheduler noop registered
[ 2.133483] io scheduler deadline registered
[ 2.133535] io scheduler cfq registered (default)
[ 2.135335] tps65217-bl tps65217-bl: no platform data provided
[ 2.135377] tps65217-bl: probe of tps65217-bl failed with error -22
[ 2.136422] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 2.139053] omap_uart 44e09000.serial: did not get pins for uart0 error: -19
[ 2.139348] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 88) is a OMAP UART0
[ 2.856380] console [ttyO0] enabled
[ 2.861263] [drm] Initialized drm 1.1.0 20060810
[ 2.879875] brd: module loaded
[ 2.890193] loop: module loaded
[ 2.893646] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write
[ 2.900932] at24 1-0054: 32768 byte 24c256 EEPROM, writable, 1 bytes/write
[ 2.908205] at24 1-0055: 32768 byte 24c256 EEPROM, writable, 1 bytes/write
[ 2.915502] at24 1-0056: 32768 byte 24c256 EEPROM, writable, 1 bytes/write
[ 2.922771] at24 1-0057: 32768 byte 24c256 EEPROM, writable, 1 bytes/write
[ 2.960437] bone-capemgr bone_capemgr.8: bone: scan failed (1 time)
[ 3.499501] bone-capemgr bone_capemgr.8: bone: scan failed (2 time)
[ 4.038556] bone-capemgr bone_capemgr.8: bone: scan failed (3 time)
[ 4.577617] bone-capemgr bone_capemgr.8: bone: scan failed (4 time)
[ 5.116680] bone-capemgr bone_capemgr.8: bone: scan failed (5 time)
[ 5.655742] bone-capemgr bone_capemgr.8: bone: scan failed (6 time)
[ 6.194808] bone-capemgr bone_capemgr.8: bone: scan failed (7 time)
[ 6.733868] bone-capemgr bone_capemgr.8: bone: scan failed (8 time)
[ 7.272933] bone-capemgr bone_capemgr.8: bone: scan failed (9 time)
[ 7.811993] bone-capemgr bone_capemgr.8: bone: scan failed (10 time)
[ 8.319981] bone-capemgr bone_capemgr.8: Failed to scan baseboard eeprom
[ 8.327049] bone-capemgr: probe of bone_capemgr.8 failed with error -110
[ 8.336567] nand_get_flash_type: 2c,da against 2c,da
[ 8.342094] ONFI param page 0 valid
[ 8.345766] ONFI flash detected
[ 8.349084] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08ABAEAWP), 256MiB, page size: 2048, OOB size: 64
[ 8.360996] omap2-nand: detected x8 NAND flash
[ 8.365660] nand: using OMAP_ECC_BCH8_CODE_HW ECC scheme
[ 8.371264] omap2-nand: using custom ecc layout
[ 8.376101] 10 ofpart partitions found on MTD device omap2-nand.0
[ 8.382494] Creating 10 MTD partitions on "omap2-nand.0":
[ 8.388166] 0x000000000000-0x000000020000 : "spl"
[ 8.395056] 0x000000020000-0x000000040000 : "spl_backup1"
[ 8.402509] 0x000000040000-0x000000060000 : "spl_backup2"
[ 8.409922] 0x000000060000-0x000000080000 : "spl_backup3"
[ 8.417186] 0x000000080000-0x000000240000 : "u-boot"
[ 8.425450] 0x000000240000-0x000000260000 : "bootenv"
[ 8.432421] 0x000000260000-0x000000280000 : "fdt"
[ 8.439049] 0x000000280000-0x000000780000 : "kernel"
[ 8.450068] 0x000000800000-0x000001c00000 : "root"
[ 8.473588] 0x000001c00000-0x000003000000 : "config"
[ 8.497370] OneNAND driver initializing
[ 8.504806] edma-dma-engine edma-dma-engine.0: allocated channel for 0:17
[ 8.512098] edma-dma-engine edma-dma-engine.0: allocated channel for 0:16
[ 8.522387] edma-dma-engine edma-dma-engine.0: allocated channel for 0:43
[ 8.529672] edma-dma-engine edma-dma-engine.0: allocated channel for 0:42
[ 8.538930] usbcore: registered new interface driver asix
[ 8.544769] usbcore: registered new interface driver cdc_ether
[ 8.551049] usbcore: registered new interface driver smsc95xx
[ 8.557172] usbcore: registered new interface driver net1080
[ 8.563195] usbcore: registered new interface driver cdc_subset
[ 8.569503] usbcore: registered new interface driver zaurus
[ 8.575489] usbcore: registered new interface driver cdc_ncm
[ 8.582216] usbcore: registered new interface driver cdc_acm
[ 8.588175] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 8.596552] Initializing USB Mass Storage driver...
[ 8.601774] usbcore: registered new interface driver usb-storage
[ 8.608074] USB Mass Storage support registered.
[ 8.613096] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
[ 8.619757] musb-hdrc musb-hdrc.0.auto: pdev->id = 0
[ 8.624994] musb-hdrc musb-hdrc.0.auto: drivers/usb/musb/musb_dsps.c:468 dsps_musb_init: OK
[ 8.633758] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
[ 8.633779] musb-hdrc: MHDRC RTL version 2.0
[ 8.633794] musb-hdrc: setup fifo_mode 4
[ 8.633822] musb-hdrc: 28/31 max ep, 16384/16384 memory
[ 8.633972] musb-hdrc musb-hdrc.0.auto: *** mode=3
[ 8.639017] musb-hdrc musb-hdrc.0.auto: *** power=250
[ 8.644963] musb-hdrc musb-hdrc.1.auto: pdev->id = 1
[ 8.650209] musb-hdrc musb-hdrc.1.auto: drivers/usb/musb/musb_dsps.c:468 dsps_musb_init: OK
[ 8.658971] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
[ 8.658991] musb-hdrc: MHDRC RTL version 2.0
[ 8.659005] musb-hdrc: setup fifo_mode 4
[ 8.659027] musb-hdrc: 28/31 max ep, 16384/16384 memory
[ 8.659146] musb-hdrc musb-hdrc.1.auto: *** mode=1
[ 8.664187] musb-hdrc musb-hdrc.1.auto: *** power=250
[ 8.669493] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver
[ 8.675895] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 1
[ 8.684131] musb-hdrc musb-hdrc.1.auto: supports USB remote wakeup
[ 8.684248] usb usb1: default language 0x0409
[ 8.684306] usb usb1: udev 1, busnum 1, minor = 0
[ 8.684330] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 8.691455] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.699026] usb usb1: Product: MUSB HDRC host driver
[ 8.704240] usb usb1: Manufacturer: Linux 3.8.13 musb-hcd
[ 8.709905] usb usb1: SerialNumber: musb-hdrc.1.auto
[ 8.715787] usb usb1: usb_probe_device
[ 8.715815] usb usb1: configuration #1 chosen from 1 choice
[ 8.715880] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[ 8.716088] hub 1-0:1.0: usb_probe_interface
[ 8.716110] hub 1-0:1.0: usb_probe_interface - got id
[ 8.716138] hub 1-0:1.0: USB hub found
[ 8.720227] hub 1-0:1.0: 1 port detected
[ 8.724368] hub 1-0:1.0: standalone hub
[ 8.724387] hub 1-0:1.0: individual port power switching
[ 8.724406] hub 1-0:1.0: no over-current protection
[ 8.724423] hub 1-0:1.0: Single TT
[ 8.724444] hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns)
[ 8.724464] hub 1-0:1.0: power on to power good time: 10ms
[ 8.724507] hub 1-0:1.0: local power source is good
[ 8.724614] hub 1-0:1.0: enabling power on all ports
[ 8.725659] mousedev: PS/2 mouse device common for all mice
[ 8.734010] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0
[ 8.741488] 44e3e000.rtc: already running
[ 8.745978] i2c /dev entries driver
[ 8.751359] pps_ldisc: PPS line discipline registered
[ 8.756839] Driver for 1-wire Dallas network protocol.
[ 8.764134] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
[ 8.771702] cpuidle: using governor ladder
[ 8.776028] cpuidle: using governor menu
[ 8.780581] of_get_named_gpio_flags exited with status 6
[ 8.780601] of_get_named_gpio_flags: can't parse gpios property
[ 8.780617] of_get_named_gpio_flags: can't parse gpios property
[ 8.780653] omap_hsmmc mmc.4: of_parse_phandle_with_args of 'reset' failed
[ 8.787874] omap_hsmmc mmc.4: Failed to get rstctl; not using any
[ 8.794685] edma-dma-engine edma-dma-engine.0: allocated channel for 0:25
[ 8.801894] edma-dma-engine edma-dma-engine.0: allocated channel for 0:24
[ 8.809224] mmc.4 supply vmmc_aux not found, using dummy regulator
[ 8.816201] omap_hsmmc mmc.4: pins are not configured from the driver
[ 8.825792] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0000
[ 8.849653] pinctrl-single 44e10800.pinmux: pin 44e10854 already requested by 44e10800.pinmux; cannot claim for gpio-leds.7
[ 8.861349] pinctrl-single 44e10800.pinmux: pin-21 (gpio-leds.7) status -22
[ 8.868652] pinctrl-single 44e10800.pinmux: could not request pin 21 on device pinctrl-single
[ 8.877677] leds-gpio gpio-leds.7: pins are not configured from the driver
[ 8.884908] of_get_named_gpio_flags exited with status 53
[ 8.884931] of_get_named_gpio_flags exited with status 54
[ 8.884952] of_get_named_gpio_flags exited with status 55
[ 8.884972] of_get_named_gpio_flags exited with status 56
[ 8.885006] of_get_named_gpio_flags exited with status 53
[ 8.885302] of_get_named_gpio_flags exited with status 54
[ 8.885518] of_get_named_gpio_flags exited with status 55
[ 8.885708] of_get_named_gpio_flags exited with status 56
[ 8.886313] ledtrig-cpu: registered to indicate activity on CPUs
[ 8.893032] edma-dma-engine edma-dma-engine.0: allocated channel for 0:36
[ 8.900226] omap-sham 53100000.sham: hw accel on OMAP rev 4.3
[ 8.908347] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2
[ 8.914628] edma-dma-engine edma-dma-engine.0: allocated channel for 0:5
[ 8.921826] edma-dma-engine edma-dma-engine.0: allocated channel for 0:6
[ 8.934258] usbcore: registered new interface driver usbhid
[ 8.940171] usbhid: USB HID core driver
[ 8.947130] TCP: cubic registered
[ 8.950642] Initializing XFRM netlink socket
[ 8.955196] NET: Registered protocol family 17
[ 8.960018] NET: Registered protocol family 15
[ 8.964863] Key type dns_resolver registered
[ 8.969505] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
[ 8.977619] ThumbEE CPU extension supported.
[ 8.982224] Registering SWP/SWPB emulation handler
[ 8.988223] registered taskstats version 1
[ 9.044440] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6
[ 9.050857] davinci_mdio 4a101000.mdio: detected phy mask fffffffe
[ 9.065240] libphy: 4a101000.mdio: probed
[ 9.069540] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720
[ 9.079410] Detected MACID = 88:c2:55:84:d8:0d
[ 9.084101] cpsw 4a100000.ethernet: NAPI disabled
[ 9.090753] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
[ 9.107144] ALSA device list:
[ 9.110277] No soundcards found.
[ 9.114457] Freeing init memory: 264K
[ 9.118376] Failed to execute /init
[ 9.380118] compile May 11 2016--14:50:30
[ 9.384445] CM_PER_SPI1_CLKCTRL 0x10002
[ 9.388483] spi_vaddr 0xfa1a0000
[ 9.391866] version 0x40300a0b
[ 9.395069] OMAP2_MCSPI_SYSSTATUS 0x1
[ 9.398905] OMAP2_MCSPI_MODULCTRL 0x1
[ 9.402737] OMAP2_MCSPI_CHCONF0 0x180103c5
[ 9.411678] Initial OMAP2_MCSPI_IRQSTATUS{0x0}OMAP2_MCSPI_IRQENABLE{0x0}
[ 9.423666] hash ok
[ 9.425925] hashtest OK
[ 9.428740] bitmain-asic: success to register device
[ 9.438346] Detect hardware version = 4
[ 9.442447] fix hardware version
[ 9.445838] hardware_version = 0x4
[ 9.449510] S5 ctrl board test V1.1
[ 9.453417] bitmain_asic_open ok
[ 9.457594] FPGA config err {0x8400c444}
[ 9.462731] stop send work to all chain
[ 9.467977] Sending open core work
[ 9.472915] Send new block cmd
[ 9.577597] Division by zero in kernel.
[ 9.581655] [<c001051d>] (unwind_backtrace+0x1/0x8c) from [<c0193c53>] (Ldiv0+0x9/0x12)
[ 9.590076] [<c0193c53>] (Ldiv0+0x9/0x12) from [<bf805807>] (nonce_query+0x4e/0x1c8 [bitmain_spi])
[ 9.599476] [<bf805807>] (nonce_query+0x4e/0x1c8 [bitmain_spi]) from [<bf801855>] (bitmain_asic_close+0x68/0x108 [bitmain_spi])
[ 9.611487] [<bf801855>] (bitmain_asic_close+0x68/0x108 [bitmain_spi]) from [<c0094f27>] (__fput+0x9b/0x154)
[ 9.621767] [<c0094f27>] (__fput+0x9b/0x154) from [<c003b13d>] (task_work_run+0x79/0x8c)
[ 9.630244] [<c003b13d>] (task_work_run+0x79/0x8c) from [<c000eb75>] (do_work_pending+0x51/0x5c)
[ 9.639426] [<c000eb75>] (do_work_pending+0x51/0x5c) from [<c000c693>] (work_pending+0x9/0x1a)
[ 9.648427] timeout {0x189b}
[ 9.651442] rev timeout {0x9b180080}
[ 9.655250] FPGA return data error
[ 9.658814] set_baud cmd_buf[0]{0x86}cmd_buf[1]{0x10}cmd_buf[2]{0x1a}cmd_buf[3]{0x17}
[ 9.790484] bitmain_asic_close
[ 9.810914] bitmain-asic: success to unregister device
[ 10.832450] compile May 11 2016--14:50:30
[ 10.836740] CM_PER_SPI1_CLKCTRL 0x2
[ 10.840409] spi_vaddr 0xfa1a0000
[ 10.843787] version 0x40300a0b
[ 10.846988] OMAP2_MCSPI_SYSSTATUS 0x1
[ 10.850820] OMAP2_MCSPI_MODULCTRL 0x1
[ 10.854656] OMAP2_MCSPI_CHCONF0 0x180103c5
[ 10.858991] Initial OMAP2_MCSPI_IRQSTATUS{0x0}OMAP2_MCSPI_IRQENABLE{0x0}
[ 10.866103] hash ok
[ 10.868322] hashtest OK
[ 10.871114] bitmain-asic: success to register device
[ 10.880696] Detect hardware version = 4
[ 10.884774] fix hardware version
[ 10.888161] hardware_version = 0x4
[ 10.891841] S5 ctrl board test V1.1
[ 10.895703] bitmain_asic_open ok
[ 10.899911] FPGA config err {0x8400c444}
[ 10.904972] stop send work to all chain
[ 10.910238] Sending open core work
[ 10.915176] Send new block cmd
[ 11.019009] Division by zero in kernel.
[ 11.023064] [<c001051d>] (unwind_backtrace+0x1/0x8c) from [<c0193c53>] (Ldiv0+0x9/0x12)
[ 11.031471] [<c0193c53>] (Ldiv0+0x9/0x12) from [<bf81f807>] (nonce_query+0x4e/0x1c8 [bitmain_spi])
[ 11.040876] [<bf81f807>] (nonce_query+0x4e/0x1c8 [bitmain_spi]) from [<bf81b855>] (bitmain_asic_close+0x68/0x108 [bitmain_spi])
[ 11.052890] [<bf81b855>] (bitmain_asic_close+0x68/0x108 [bitmain_spi]) from [<c0094f27>] (__fput+0x9b/0x154)
[ 11.063170] [<c0094f27>] (__fput+0x9b/0x154) from [<c003b13d>] (task_work_run+0x79/0x8c)
[ 11.071653] [<c003b13d>] (task_work_run+0x79/0x8c) from [<c000eb75>] (do_work_pending+0x51/0x5c)
[ 11.080842] [<c000eb75>] (do_work_pending+0x51/0x5c) from [<c000c693>] (work_pending+0x9/0x1a)
[ 11.089848] timeout {0x189b}
[ 11.092860] rev timeout {0x9b180080}
[ 11.096887] FPGA return data error
[ 11.100468] set_baud cmd_buf[0]{0x86}cmd_buf[1]{0x10}cmd_buf[2]{0x1a}cmd_buf[3]{0x17}
[ 11.231890] bitmain_asic_close
[ 11.252059] bitmain-asic: success to unregister device
[ 12.273684] compile May 11 2016--14:50:30
[ 12.277972] CM_PER_SPI1_CLKCTRL 0x2
[ 12.281642] spi_vaddr 0xfa1a0000
[ 12.285023] version 0x40300a0b
[ 12.288219] OMAP2_MCSPI_SYSSTATUS 0x1
[ 12.292047] OMAP2_MCSPI_MODULCTRL 0x1
[ 12.295878] OMAP2_MCSPI_CHCONF0 0x180103c5
[ 12.300214] Initial OMAP2_MCSPI_IRQSTATUS{0x0}OMAP2_MCSPI_IRQENABLE{0x0}
[ 12.307346] hash ok
[ 12.309572] hashtest OK
[ 12.312359] bitmain-asic: success to register device
[ 12.321978] Detect hardware version = 4
[ 12.326058] fix hardware version
[ 12.329454] hardware_version = 0x4
[ 12.333135] S5 ctrl board test V1.1
[ 12.336993] bitmain_asic_open ok
[ 12.341144] FPGA config err {0x8400c444}
[ 12.346316] stop send work to all chain
[ 12.351570] Sending open core work
[ 12.356500] Send new block cmd
[ 12.460408] Division by zero in kernel.
[ 12.464460] [<c001051d>] (unwind_backtrace+0x1/0x8c) from [<c0193c53>] (Ldiv0+0x9/0x12)
[ 12.472879] [<c0193c53>] (Ldiv0+0x9/0x12) from [<bf839807>] (nonce_query+0x4e/0x1c8 [bitmain_spi])
[ 12.482278] [<bf839807>] (nonce_query+0x4e/0x1c8 [bitmain_spi]) from [<bf835855>] (bitmain_asic_close+0x68/0x108 [bitmain_spi])
[ 12.494287] [<bf835855>] (bitmain_asic_close+0x68/0x108 [bitmain_spi]) from [<c0094f27>] (__fput+0x9b/0x154)
[ 12.504571] [<c0094f27>] (__fput+0x9b/0x154) from [<c003b13d>] (task_work_run+0x79/0x8c)
[ 12.513043] [<c003b13d>] (task_work_run+0x79/0x8c) from [<c000eb75>] (do_work_pending+0x51/0x5c)
[ 12.522239] [<c000eb75>] (do_work_pending+0x51/0x5c) from [<c000c693>] (work_pending+0x9/0x1a)
[ 12.531235] timeout {0x189b}
[ 12.534251] rev timeout {0x9b180080}
[ 12.538059] FPGA return data error
[ 12.541632] set_baud cmd_buf[0]{0x86}cmd_buf[1]{0x10}cmd_buf[2]{0x1a}cmd_buf[3]{0x17}
[ 12.673296] bitmain_asic_close
[ 12.693494] bitmain-asic: success to unregister device
[ 13.715078] compile May 11 2016--14:50:30
[ 13.719361] CM_PER_SPI1_CLKCTRL 0x2
[ 13.723031] spi_vaddr 0xfa1a0000
[ 13.726413] version 0x40300a0b
[ 13.729607] OMAP2_MCSPI_SYSSTATUS 0x1
[ 13.733429] OMAP2_MCSPI_MODULCTRL 0x1
[ 13.737256] OMAP2_MCSPI_CHCONF0 0x180103c5
[ 13.741593] Initial OMAP2_MCSPI_IRQSTATUS{0x0}OMAP2_MCSPI_IRQENABLE{0x0}
[ 13.748722] hash ok
[ 13.750941] hashtest OK
[ 13.753733] bitmain-asic: success to register device
[ 13.763312] Detect hardware version = 4
[ 13.767384] fix hardware version
[ 13.770770] hardware_version = 0x4
[ 13.774450] S5 ctrl board test V1.1
[ 13.778317] bitmain_asic_open ok
[ 13.782464] FPGA config err {0x8400c444}
[ 13.787642] stop send work to all chain
[ 13.792888] Sending open core work
[ 13.797817] Send new block cmd
[ 13.901815] Division by zero in kernel.
[ 13.905861] [<c001051d>] (unwind_backtrace+0x1/0x8c) from [<c0193c53>] (Ldiv0+0x9/0x12)
[ 13.914277] [<c0193c53>] (Ldiv0+0x9/0x12) from [<bf853807>] (nonce_query+0x4e/0x1c8 [bitmain_spi])
[ 13.923672] [<bf853807>] (nonce_query+0x4e/0x1c8 [bitmain_spi]) from [<bf84f855>] (bitmain_asic_close+0x68/0x108 [bitmain_spi])
[ 13.935682] [<bf84f855>] (bitmain_asic_close+0x68/0x108 [bitmain_spi]) from [<c0094f27>] (__fput+0x9b/0x154)
[ 13.945971] [<c0094f27>] (__fput+0x9b/0x154) from [<c003b13d>] (task_work_run+0x79/0x8c)
[ 13.954447] [<c003b13d>] (task_work_run+0x79/0x8c) from [<c000eb75>] (do_work_pending+0x51/0x5c)
[ 13.963635] [<c000eb75>] (do_work_pending+0x51/0x5c) from [<c000c693>] (work_pending+0x9/0x1a)
[ 13.972631] timeout {0x189b}
[ 13.975647] rev timeout {0x9b180080}
[ 13.979467] FPGA return data error
[ 13.983033] set_baud cmd_buf[0]{0x86}cmd_buf[1]{0x10}cmd_buf[2]{0x1a}cmd_buf[3]{0x17}
[ 14.114702] bitmain_asic_close
[ 14.134939] bitmain-asic: success to unregister device
[ 15.156399] compile May 11 2016--14:50:30
[ 15.160682] CM_PER_SPI1_CLKCTRL 0x2
[ 15.164349] spi_vaddr 0xfa1a0000
[ 15.167726] version 0x40300a0b
[ 15.170917] OMAP2_MCSPI_SYSSTATUS 0x1
[ 15.174744] OMAP2_MCSPI_MODULCTRL 0x1
[ 15.178575] OMAP2_MCSPI_CHCONF0 0x180103c5
[ 15.182917] Initial OMAP2_MCSPI_IRQSTATUS{0x0}OMAP2_MCSPI_IRQENABLE{0x0}
[ 15.190035] hash ok
[ 15.192260] hashtest OK
[ 15.195045] bitmain-asic: success to register device
[ 15.204718] Detect hardware version = 4
[ 15.208789] fix hardware version
[ 15.212178] hardware_version = 0x4
[ 15.215853] S5 ctrl board test V1.1
[ 15.219721] bitmain_asic_open ok
[ 15.223869] FPGA config err {0x8400c444}
[ 15.229026] stop send work to all chain
[ 15.234271] Sending open core work
[ 15.239206] Send new block cmd
[ 15.343216] Division by zero in kernel.
[ 15.347263] [<c001051d>] (unwind_backtrace+0x1/0x8c) from [<c0193c53>] (Ldiv0+0x9/0x12)
[ 15.355668] [<c0193c53>] (Ldiv0+0x9/0x12) from [<bf86d807>] (nonce_query+0x4e/0x1c8 [bitmain_spi])
[ 15.365063] [<bf86d807>] (nonce_query+0x4e/0x1c8 [bitmain_spi]) from [<bf869855>] (bitmain_asic_close+0x68/0x108 [bitmain_spi])
[ 15.377070] [<bf869855>] (bitmain_asic_close+0x68/0x108 [bitmain_spi]) from [<c0094f27>] (__fput+0x9b/0x154)
[ 15.387350] [<c0094f27>] (__fput+0x9b/0x154) from [<c003b13d>] (task_work_run+0x79/0x8c)
[ 15.395816] [<c003b13d>] (task_work_run+0x79/0x8c) from [<c000eb75>] (do_work_pending+0x51/0x5c)
[ 15.405000] [<c000eb75>] (do_work_pending+0x51/0x5c) from [<c000c693>] (work_pending+0x9/0x1a)
[ 15.413997] timeout {0x189b}
[ 15.417013] rev timeout {0x9b180080}
[ 15.420824] FPGA return data error
[ 15.424392] set_baud cmd_buf[0]{0x86}cmd_buf[1]{0x10}cmd_buf[2]{0x1a}cmd_buf[3]{0x17}
[ 15.556110] bitmain_asic_close
[ 15.576304] bitmain-asic: success to unregister device
[ 16.597853] compile May 11 2016--14:50:30
[ 16.602138] CM_PER_SPI1_CLKCTRL 0x2
[ 16.605809] spi_vaddr 0xfa1a0000
[ 16.609184] version 0x40300a0b
[ 16.612382] OMAP2_MCSPI_SYSSTATUS 0x1
[ 16.616220] OMAP2_MCSPI_MODULCTRL 0x1
[ 16.620063] OMAP2_MCSPI_CHCONF0 0x180103c5
[ 16.624393] Initial OMAP2_MCSPI_IRQSTATUS{0x0}OMAP2_MCSPI_IRQENABLE{0x0}
[ 16.631531] hash ok
[ 16.633761] hashtest OK
[ 16.636559] bitmain-asic: success to register device
[ 16.646155] Detect hardware version = 4
[ 16.650228] fix hardware version
[ 16.653616] hardware_version = 0x4
[ 16.657296] S5 ctrl board test V1.1
[ 16.661167] bitmain_asic_open ok
[ 16.665320] FPGA config err {0x8400c444}
[ 16.670493] stop send work to all chain
[ 16.675733] Sending open core work
[ 16.680670] Send new block cmd
[ 16.784627] Division by zero in kernel.
[ 16.788687] [<c001051d>] (unwind_backtrace+0x1/0x8c) from [<c0193c53>] (Ldiv0+0x9/0x12)
[ 16.797098] [<c0193c53>] (Ldiv0+0x9/0x12) from [<bf887807>] (nonce_query+0x4e/0x1c8 [bitmain_spi])
[ 16.806509] [<bf887807>] (nonce_query+0x4e/0x1c8 [bitmain_spi]) from [<bf883855>] (bitmain_asic_close+0x68/0x108 [bitmain_spi])
[ 16.818514] [<bf883855>] (bitmain_asic_close+0x68/0x108 [bitmain_spi]) from [<c0094f27>] (__fput+0x9b/0x154)
[ 16.828792] [<c0094f27>] (__fput+0x9b/0x154) from [<c003b13d>] (task_work_run+0x79/0x8c)
[ 16.837269] [<c003b13d>] (task_work_run+0x79/0x8c) from [<c000eb75>] (do_work_pending+0x51/0x5c)
[ 16.846464] [<c000eb75>] (do_work_pending+0x51/0x5c) from [<c000c693>] (work_pending+0x9/0x1a)
[ 16.855466] timeout {0x189b}
[ 16.858480] rev timeout {0x9b180080}
[ 16.862284] FPGA return data error
[ 16.865858] set_baud cmd_buf[0]{0x86}cmd_buf[1]{0x10}cmd_buf[2]{0x1a}cmd_buf[3]{0x17}
[ 16.997513] bitmain_asic_close
[ 17.381234] jffs2: notice: (193) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 18.260875] net eth0: initializing cpsw version 1.12 (0)
[ 18.268739] net eth0: phy found : id is : 0x7c0f1
[ 18.273736] libphy: PHY 4a101000.mdio:01 not found
[ 18.278762] net eth0: phy 4a101000.mdio:01 not found on slave 1
[ 21.345655] libphy: 4a101000.mdio:00 - Link is Up - 100/Full
[ 36.720129] bitmain-asic: success to unregister device
[ 37.742297] compile May 11 2016--14:50:30
[ 37.746582] CM_PER_SPI1_CLKCTRL 0x2
[ 37.750252] spi_vaddr 0xfa1a0000
[ 37.753631] version 0x40300a0b
[ 37.756827] OMAP2_MCSPI_SYSSTATUS 0x1
[ 37.760658] OMAP2_MCSPI_MODULCTRL 0x1
[ 37.764490] OMAP2_MCSPI_CHCONF0 0x180103c5
[ 37.768817] Initial OMAP2_MCSPI_IRQSTATUS{0x0}OMAP2_MCSPI_IRQENABLE{0x0}
[ 37.775935] hash ok
[ 37.778156] hashtest OK
[ 37.780948] bitmain-asic: success to register device
[ 37.905935] Detect hardware version = 4
[ 37.910000] fix hardware version
[ 37.913385] hardware_version = 0x4
[ 37.921671] S5 ctrl board test V1.1
[ 37.931243] bitmain_asic_open ok
[ 37.949342] Detect device
[ 37.952172] soft ctrl rst time
[ 37.956757] reset hash asic
[ 37.959726] clear FPGA nonce buffer
[ 37.967119] FPGA return data error
[ 37.971163] FPGA don't code
[ 38.974094] soft ctrl rst time
[ 38.977386] reset hash asic
[ 38.980320] clear FPGA nonce buffer
[ 38.984034] FPGA return data error
[ 38.987600] FPGA don't code
[ 40.089378] total chain_num{0}
[ 40.092605] FPGA detect asic addr err
[ 40.092605]
[ 40.097982]
[ 40.097982]
[ 40.097982] !!!!Restart1 detect asic addr!!!
[ 40.097982]
[ 40.107094] total chain_num{0}
[ 40.110285] FPGA detect asic addr err
[ 40.110285]
[ 40.115653]
[ 40.115653]
[ 40.115653] !!!!Restart2 detect asic addr!!!
[ 40.115653]
[ 40.124758] total chain_num{0}
[ 40.127952] FPGA detect asic addr err
[ 40.127952]
[ 40.133323]
[ 40.133323]
[ 40.133323] !!!!Restart3 detect asic addr!!!
[ 40.133323]
[ 40.142433] total chain_num{0}
[ 40.145635] FPGA detect asic addr err
[ 40.145635]
[ 40.151006]
[ 40.151006]
[ 40.151006] !!!!soft set defult asic num 0!!!
[ 40.151006]
[ 40.160192] clear FPGA nonce buffer
[ 40.163920] FPGA return data error
[ 40.167486] FPGA don't code
(Moderator's note: This post was edited by frodocooper to use code tags for the log output.) |
|
|
|
|
robertroberrt
Newbie
Offline
Activity: 3
Merit: 0
|
|
June 19, 2016, 07:38:17 PM |
|
any ideas on the FPGA don't code error? I am at a loss now.
|
|
|
|
|
philipma1957
Legendary
 Online
Activity: 4116
Merit: 7850
'The right to privacy matters'
|
|
June 19, 2016, 10:33:06 PM |
|
any ideas on the FPGA don't code error? I am at a loss now.
well the s-7 will not run if the controller does not detect the fans. so play with the 2 fan connections. sometimes the tach wire which shows the fan speed to the controller is loose. |
|
|
|
robertroberrt
Newbie
Offline
Activity: 3
Merit: 0
|
|
June 20, 2016, 07:08:16 PM |
|
Played with the connections and looked in the fans. Nothing was loose. I put power to individual cards, checked, and still no hasing. I did this with all three boards 1 at a time, each time powering up and down.....no success. I think it has to be the control board, but anyone else has a suggestion I will try it. I appreciate the responses.
|
|
|
|
|
notlist3d
Legendary
Offline
Activity: 1456
Merit: 1000
|
|
June 20, 2016, 07:39:17 PM |
|
Played with the connections and looked in the fans. Nothing was loose. I put power to individual cards, checked, and still no hasing. I did this with all three boards 1 at a time, each time powering up and down.....no success. I think it has to be the control board, but anyone else has a suggestion I will try it. I appreciate the responses.
Just to check with first miner your AP3 psu is hooked up to 205 volts or more on electricity? Did you purchase a new miner from Bitmain or is it used? Also are you able to post a link to your miner status page? How you said you don't know how to insert image if on windows and recent you can use the "snipping tool" just search for it and it allows to take images, or you can look up screen print/paint combo. But after throw it up on any standard image site (I personally use photobucket but there are a TON of options). It wont let you post image directly in forum due to rank but you can post link to image. |
|
|
|
|
|
mannyg
|
|
January 22, 2018, 10:40:27 PM |
|
I have an S7 doing this exact thing. I'm thinking something is up with the controller board, but not sure until i receive another one to test.
Ever find a solution to this?
|
|
|
|
|
onegiantcock
Copper Member
Jr. Member
Offline
Activity: 96
Merit: 1
|
|
January 23, 2018, 03:47:13 PM |
|
I would try these steps: change psu, change pool, change worker name, change to static IP. If still no-go reflash controller board firmware. If still no hash, disassemble miner, inspecting hash boards for solder defects (signs of overheating) try hash boards one at a time on known good controller. If still no hash - you may need hash board repair/rework/reflow.
|
|
|
|
|
|
mannyg
|
|
January 23, 2018, 04:06:10 PM |
|
I would try these steps: change psu, change pool, change worker name, change to static IP. If still no-go reflash controller board firmware. If still no hash, disassemble miner, inspecting hash boards for solder defects (signs of overheating) try hash boards one at a time on known good controller. If still no hash - you may need hash board repair/rework/reflow.
I have no idea how i figured it out, but i did. Seems that a chip (buck regulator) on the IO controller was having trouble... MP1484EN right next to the small red LED near the 18pin headers. I also had to power on the BeagleBone Board externally with 5v. Seems that something on the IO controller stopped passing power over to the BBB. Once I had the BBB on, the IO controller still wasnt working right. The Fans were getting power, and eventually some activity happened on the IO board (red/green activity lights near ethernet jack) thanks to the BBB being on, but the 18pin headers (USB connections) there was nothing passing through to power that side on. I attached a PickIt3 to the hashboard via the ICSP header and violla!! the red LED lit up again. I separated the 2 boards and hooked the IO controller to 12v, powered on the 12v and started poking around with a volt meter around that buck regulator and suddenly the red LED lit up along with the green LEDs near the reset switches. I think i accidentally shorted 2 pins for a brief second? Whatever it was, it told it to work again almost as if it had taken a nap. For the hell of it, i disconnected all, flashed new hex files to the PICs on the hash boards, connected everything again and reflashed the firmware. It all works but I still have to power the BBB externally.  |
|
|
|
|
|
