Claymore's Dual Miner: Settings and statistics

[ps_jb]

Question:

Why my AfterBurner does not allow me to change memory clock?

Win 7, Crimson 15.12

4x R9 390 (3x XFN and 1x PowerColor)

Should I unlock smth in AB or what ?

[Mzie]

did you try -dcri 25? it should work and give over 1000Mh/s for sia

[hiddensphinx]

MSI GTX 1070 getting 27MH/s with DaggerHashimoto and    0.38 GH/s with Decreed  dual mining

is this good?

[brizio71]

MSI GTX 1070 getting 27MH/s with DaggerHashimoto and    0.38 GH/s with Decreed  dual mining

is this good?

what is the power drain ?

Can you try with siacoin too ?

[hiddensphinx]

MSI GTX 1070 getting 27MH/s with DaggerHashimoto and    0.38 GH/s with Decreed  dual mining

is this good?

what is the power drain ?

Can you try with siacoin too ?

Power drain is at 45% according to MSI Afterburner...GPU temp = 60 Celsius and CPU TEMP = 55 Celsius

[Amph]

increase the mem to 400 at least, you can boost the speed for eth to 30MH

[hatshepsut93]

GTX 1060 reporting in.

Windows 10 1607, driver 372.54

Ether 3.839 MH, Decred 38.393 MH. Is there anything I can do, or my card is not supported?

[blue-yu]

Win7, 3*gtx970, +150cpu, +500mem, 368.81 driver:

dual: 63Mh/s eth + 627Mh/s dcr
single: 66Mh/s eth

genoil: 65Mh/s

BR...

[janos666]

I run some reference design RX480 8Gb cards with default GPU clock/voltage settings (for some reason, these controls are completely locked in WattMan whenever a mining software is running) and the VRAM clocked to 2250MHz (max allowed) with default RAM voltage (I could try under-volting the RAM but I don't think it would worth the hassle since it draws significantly less power than the GPU to begin with and it's overclocked, so it probably needs the voltage anyway...) and I get 27 + 405 Mh/s (ETH+DCR) on each with Claymore's software (v6.1) on Win10 RS1 + Catalyst 16.8.2 beta.

The PSU is rated at ~90% efficiency at ~50% load (and that's roughly the current situations with the 1200W rated PSU drawing 780W from the wall with 3 of these cards + the 30W idle platform [measured alone], so it's ~60% load), so the cards take roughly ~225W (according to measurements and calculations) which is exactly their maximum theoretical limit (150*1.5=225W with the PowerLimit set to +50% over the original 150W TDP limit).

[Strannik-74]

130W

[rawbert]

130W

130W in gpuz or at the wall?

[Strannik-74]

130W in gpuz or at the wall?

rig without load 110W, rig load 230W, power meter reading from the power socket.

[xeridea]

Sapphire 470 8GB 24.3 / 445 MH/s , 1260MHz steady clock, 0.95v core, 109w 88.5% ASIC Quality
Powercolor Red Devil 470 4GB 22 / 405 MH/s, ~1140 Mhz varying boost, 0.97v core, 77.9% ASIC quality
Mining Eth/Sia, 80+ Bronze PSU, 85% eff, ~130 for each card, 155 at the wall, 109w GPU only draw

The 8GB version mines Eth faster, (8GHz memory vs 7Ghz), and has more stable boost (at least mine does), but costs $40 more.

The GTX 1060 3GB just came out, for $200.  1 out of 12 CUs disabled vs the normal 1060, same clocks and memory.  Normal 1060 gets 20MHs Eth, it may be a decent card for similar price.  Anyone getting one feel free to post!

[DrX]

RIG1: (Windows 7, AMD 15.12, intel e8400, 2gb ram)

MSI Gaming 4G 290 , Eth 27.5 Sia/Dcr 636Mh/s , Mem 1250 Core 1070.
MSI Gaming 4G 290x , Eth 28.5 Sia/Dcr 656Mh/s , Mem 1350 Core 1070.

Total Eth 56/57 + Sia/Dcr 1292Mh/s

EthDcrMiner64.exe -dbg -1 -epool POOL -ewal MYWALLET -eworker WORKER.1 -epsw PASSWORD -allpools 1 -dpool POOL -dwal WORKER.1 -dpsw PASSWORD -dcoin sc -dcri 46,46

RIG2: (Windows 8.1, AMD 15.12, amd x2 4200. 2gb ram)

XFX 7950 , Eth 15.7Mh/s Sia/Dcr 361Mh/s, Mem 1250 Core 900
XFX 7950, Eth 16.5Mh/s Sia/Dcr 386Mh/s , Mem 1500 Core 900.
XFX 280 , Eth 16.5Mh/s Sia/Dcr 386Mh/s, Mem 1500 Core 900.

Total Eth 48.7/49.7 + Sia/Dcr 1133Mh/s

Mining DCR gives 1Mh/s more on both rigs.

EthDcrMiner64.exe -dbg -1 -epool POOL -ewal MYWALLET -eworker WORKER.2 -epsw PASSWORD -allpools 1 -dpool POOL -dwal WORKER.2 -dpsw PASSWORD -dcoin sc -dcri 46,46,46

Total power from the wall 1350w (SIA)
Total power from the wall 1250w (DCR)


Updated 19.10.2016

[DrX]

Hello,

I'm using 2x R390 mining eth and sc using this command:

EthDcrMiner64.exe -epool eth-asia1.nanopool.org:9999 -ewal <address> -epsw x -eworker <worker> -cclock 1100 -etha 0 -ethi 8 -dcri 40 -dpool "http://siamining.com:9980/miner/header?address=<address>&worker=<worker>" -dcoin sia

eth: 48
sc: 930

Is there any way to increase those speed? Any parameter at the command to be changed?
Appreciate for any info.

Thanks.

Play with dcri, optimal should be between 35-50 (You can adjust it with + and - keys while mining) , you can also try -ethi 16....and maybe -cclock 1120 -mclock 1250?

Check settings from other people stats...

[Trimegistus]

RIG specs:

Asrock H81 Pro BTC
8 GB RAM + 16 GB Pagefile
6 x Sapphire RX 480 Nitro+  OC 4GB
USB Powered Risers
2 x Corsair RM850X

Software:
Windows 10 x64
AMD drivers 16.9.1

Miner Settings:
Claymore v6.4
-dcri 25
-ethi 16

Stock settings:

GPU: 1305 MHz, 1150 mV
Mem: 1750 MHz, 1000 mv

Speed per card: 22.1 MHs ETC, 276 MHs SC
Power per card: ~130W (GPU-Z)

Underclock:

GPU: 1250 MHz, 1025 mV
Mem: 1850 MHz, Auto

Speed per card: 22 MHs ETC, 275 MHs SC
Power per card: ~105W (GPU-Z)

Unfortunately, I cannot get the miner to stabilize with a higher memory speed, it crashes after a few minutes if I set it at 1900 MHz

[vapourminer]

rig 1 (daily driver)
win7 64, 16 gb ram, gigabyte Z77X UD5H, i5 3570K
claymore 7.0
16.8.2 driver

sapphire R9 390 Nitro 8 gb
1100 gpu, 1500 mem -50 mv +20 power limit
-40 dcri

29 MH/s eth
580 MH/s  sia

rig 2
ubuntu 15.10, 8 gb ram, gigabyte Z97X UDH3, intel G1840
claymore 7.0
15.12 driver

sapphire R9 390 nitro 8 gb
1100 gpu 1500 mem stock volts
-40 dcri

30 MH/s eth
606 MH/s sia

sapphire R9 380 ITX 2 gb
1100 gpu, 1400 mem stock volts
-40 dcri

19 MH/s eth
386 MH/s sia

[Trimegistus]

Updated stats and settings:

RIG specs:

Asrock H81 Pro BTC
8 GB RAM + 16 GB Pagefile
6 x Sapphire RX 480 Nitro+  OC 4GB
USB Powered Risers
2 x Corsair RM850X

Software:
Windows 10 x64
AMD drivers 16.9.1

Miner Settings:
Claymore v6.4
-dcri 25
-ethi 16

Stock settings:

GPU: 1305 MHz, 1150 mV
Mem: 1750 MHz, 1000 mv

Speed per card: 22.1 MHs ETC, 276 MHs SC
Power per card: ~130W (GPU-Z)

Underclock:

GPU: 800 MHz, 900 mV
Mem: 1750 MHz, 800 mV

Speed per card: 22 MHs ETC, 275 MHs SC
Power per card: ~55W (GPU-Z)

This is sweet!

[Dobmader]

Question:

Why my AfterBurner does not allow me to change memory clock?

Win 7, Crimson 15.12

4x R9 390 (3x XFN and 1x PowerColor)

Should I unlock smth in AB or what ?

You might need to tick the Extehnd official overclocking limits and the Diable ULPS in the general setting tab.

[Tilos]

Here is my Config for Dual Mining with 570RX @ 1130 CoreClock, 2050 MemClock and 1500 Straps up to 2000

Ethereum 29MH/s each Card
Siacoin    460 MH/s each Card

Config:
-mode 0 -epool stratum+tcp://eu2.ethermine.org:4444 -ewal 0x9b70fcff8d8291dc028f2dc6ea6612e10fa6721a -eworker WhiteIce -epsw x -mport 0 -allcoins 1 -allpools 1 -dpool stratum+tcp://us-west.siamining.com:7777 -dwal 11d44524e1203f6f6accae2ab7e1a7b3720fa3b6ad840eee13ccfe479ecd23800dd7e256c323.Yo urWorkerName -dcoin sia -dcri 16 



SC: GPU0 454.240 Mh/s, GPU1 464.045 Mh/s
ETH: 06/11/17-08:56:37 - New job from eu2.ethermine.org:4444
ETH - Total Speed: 57.336 Mh/s, Total Shares: 30, Rejected: 0, Time: 00:39
ETH: GPU0 29.362 Mh/s, GPU1 29.274 Mh/s
SC - Total Speed: 917.376 Mh/s, Total Shares: 470, Rejected: 0
SC: GPU0 453.798 Mh/s, GPU1 463.578 Mh/s
GPU0 t=65C fan=88%, GPU1 t=65C fan=49%
SC: 06/11/17-08:56:46 - SHARE FOUND - (GPU 0)
SC: Share accepted (152 ms)!
ETH: 06/11/17-08:56:46 - New job from eu2.ethermine.org:4444
ETH - Total Speed: 57.413 Mh/s, Total Shares: 30, Rejected: 0, Time: 00:39
ETH: GPU0 29.399 Mh/s, GPU1 29.014 Mh/s
SC - Total Speed: 918.604 Mh/s, Total Shares: 471, Rejected: 0
SC: GPU0 454.382 Mh/s, GPU1 464.222 Mh/s
SC: 06/11/17-08:56:48 - SHARE FOUND - (GPU 1)
SC: Share accepted (153 ms)!
ETH: 06/11/17-08:56:54 - New job from eu2.ethermine.org:4444
ETH - Total Speed: 57.406 Mh/s, Total Shares: 30, Rejected: 0, Time: 00:39
ETH: GPU0 29.420 Mh/s, GPU1 28.985 Mh/s
SC - Total Speed: 918.487 Mh/s, Total Shares: 472, Rejected: 0
SC: GPU0 454.721 Mh/s, GPU1 463.766 Mh/s
SC: 06/11/17-08:57:00 - SHARE FOUND - (GPU 1)
SC: Share accepted (152 ms)!
SC: 06/11/17-08:57:00 - SHARE FOUND - (GPU 0)
SC: Share accepted (152 ms)!
ETH: 06/11/17-08:57:00 - New job from eu2.ethermine.org:4444
ETH - Total Speed: 57.374 Mh/s, Total Shares: 30, Rejected: 0, Time: 00:39
ETH: GPU0 29.384 Mh/s, GPU1 29.190 Mh/s
SC - Total Speed: 917.981 Mh/s, Total Shares: 474, Rejected: 0
SC: GPU0 454.141 Mh/s, GPU1 463.840 Mh/s