Etarminer - New cuda miner for ethereum

[jk_14]

LINUX version Etarminer 1_8 available
https://drive.google.com/drive/folders/0B9DK4ZXu8liUMkxpVkxaSHJGTms
Tested on Ubuntu 16.04

Code:

root@kopiemtu:~/ETAR# ./Etarminer -url http://coinotron.com:3344 -wlt jk_14.w015 -eml pass
[START launcher]
[START EtarminerSecondary]

(EtarminerSecondary:10657): Gtk-WARNING **: cannot open display:
[restart miner]-url http://coinotron.com:3344 -wlt jk_14.w015 -eml pass

(EtarminerSecondary:10685): Gtk-WARNING **: cannot open display:
[restart miner]-url http://coinotron.com:3344 -wlt jk_14.w015 -eml pass

(EtarminerSecondary:10722): Gtk-WARNING **: cannot open display:
[restart miner]-url http://coinotron.com:3344 -wlt jk_14.w015 -eml pass

And is it possible to run it without GUI ?
i.e. after:
service lightdm stop

[1715557450]

1715557450

[Etar]

LINUX version Etarminer 1_8 available
https://drive.google.com/drive/folders/0B9DK4ZXu8liUMkxpVkxaSHJGTms
Tested on Ubuntu 16.04

Code:

root@kopiemtu:~/ETAR# ./Etarminer -url http://coinotron.com:3344 -wlt jk_14.w015 -eml pass
[START launcher]
[START EtarminerSecondary]

(EtarminerSecondary:10657): Gtk-WARNING **: cannot open display:
[restart miner]-url http://coinotron.com:3344 -wlt jk_14.w015 -eml pass

(EtarminerSecondary:10685): Gtk-WARNING **: cannot open display:
[restart miner]-url http://coinotron.com:3344 -wlt jk_14.w015 -eml pass

(EtarminerSecondary:10722): Gtk-WARNING **: cannot open display:
[restart miner]-url http://coinotron.com:3344 -wlt jk_14.w015 -eml pass

And is it possible to run it without GUI ?
i.e. after:
service lightdm stop

 RELOAD Archive . I Fix this problem.  Use -GUIDIS in comandline (example in START.sh)

[izeban]

Hmm
I just call
Etarminer -url http://eu2.ethermine.org:4444 -wlt "mywalletadress.worker -wrk workername -eml x -int 21 -wsz 128 -ess 1
but ther eis no reported hashrate shown in ethermine.
any advice to that?

I have two gtx970 in sli mode at 35.2 mh/s rate (gpu@1499 mhz watercooled)

Ot on:
Maybe one has an advice, too to my watercooling stuff.
An other question is that my cooling water exits the second gpu at 60 °C (after the first it''s 41°C), so I plan to put a radiator in between the two gpus. Is that a good idea?
The System is cooled with aquaduct 720 xt mark iv at the moment.
ot off

[Ryoga1980]

Try disable SLI in Nvidia COntrol Panel, I could not get it to work with SLI Enabled

Getting 40 Mh/s on 2xGTX970 intensity 18,20

my bat:
Etarminer -url http://eth-eu1.nanopool.org:9999 -wlt walletaddress -wrk workername -eml  email -intg g0 18 g1 20 -wsz 128 -exp 0 -ess 0 -toffg g0 87

Hmm
I just call
Etarminer -url http://eu2.ethermine.org:4444 -wlt "mywalletadress.worker -wrk workername -eml x -int 21 -wsz 128 -ess 1
but ther eis no reported hashrate shown in ethermine.
any advice to that?

I have two gtx970 in sli mode at 35.2 mh/s rate (gpu@1499 mhz watercooled)

Ot on:
Maybe one has an advice, too to my watercooling stuff.
An other question is that my cooling water exits the second gpu at 60 °C (after the first it''s 41°C), so I plan to put a radiator in between the two gpus. Is that a good idea?
The System is cooled with aquaduct 720 xt mark iv at the moment.
ot off