Pandaminer -> Linux -> Modded Roms

[miropp]

if you are in Europe - how much they write on invoice? (because high VAT...)

30 $ for Case
10 $ for Fan

Thanks.
What EU customs code (Taric) you use?

[ZedZedNova]

I'm pretty sure Claymore isn't going to release anything for linux anymore. Perhaps he will, but i don't think so..

I'm running claymore's v9.3 ZEC miner on linux (ethOS), but can't speak for any of his other miners running on linux. I probably should upgrade since v9.3 is out. I probably should to do a comparo between the latest from optiminer and claymore.

Edit: I just upgraded to claymore v9.3 and will check to see what flypool reports as my 24hour hash rate. Currently it reports 141.4 H/s.

upgrade from 9.2 to 9.3 produced a yawn. rate is the same at the pool after almost 24 hours.

[jadefalke]

if you are in Europe - how much they write on invoice? (because high VAT...)

30 $ for Case
10 $ for Fan

Thanks.
What EU customs code (Taric) you use?

i used nothing DHL showed up on my Door and asked for 37 Euro, i paid them, end of story.

[philipma1957]

op and I have been kicking around ideas  of how to work out a linux for pandaminer distribution.

 I may start a separate thread.

[peoples]

Hm seems like fans are not controlable ? Anyone mastered changing fanspeed on this panda ?

[Eliovp]

Hm seems like fans are not controlable ? Anyone mastered changing fanspeed on this panda ?

Nope, they're directly connected to the mainboard.

I'm working on a sollution for this as i don't need them to run at 100%

[philipma1957]

I opened a thread up to try to figure funding for Evliop's linux build for the PandaMiner


https://bitcointalk.org/index.php?topic=1740719.0

[QuintLeo]

Hm seems like fans are not controlable ? Anyone mastered changing fanspeed on this panda ?

Nope, they're directly connected to the mainboard.

I'm working on a sollution for this as i don't need them to run at 100%

 Not going to hurt anything if they do, and helps keep things cooler for better longevity.

 Now, if they were the GHE screamers I could see wanting to slow them down!

 Have you checked to see if they even have speed control at all (4 wire interface)?
 A lot of Deltas are 3-wire "tach output no PWM speed control capability only".

[TheRider]

Hm seems like fans are not controlable ? Anyone mastered changing fanspeed on this panda ?

Nope, they're directly connected to the mainboard.

I'm working on a sollution for this as i don't need them to run at 100%

 Not going to hurt anything if they do, and helps keep things cooler for better longevity.

 Now, if they were the GHE screamers I could see wanting to slow them down!

 Have you checked to see if they even have speed control at all (4 wire interface)?
 A lot of Deltas are 3-wire "tach output no PWM speed control capability only".

I vaguely recall Phil or someone else mentioning they were 3 pin wire fans, thus no speed control.

[philipma1957]

Hm seems like fans are not controlable ? Anyone mastered changing fanspeed on this panda ?

Nope, they're directly connected to the mainboard.

I'm working on a sollution for this as i don't need them to run at 100%

 Not going to hurt anything if they do, and helps keep things cooler for better longevity.

 Now, if they were the GHE screamers I could see wanting to slow them down!

 Have you checked to see if they even have speed control at all (4 wire interface)?
 A lot of Deltas are 3-wire "tach output no PWM speed control capability only".

I vaguely recall Phil or someone else mentioning they were 3 pin wire fans, thus no speed control.

Let me look at photos I,took.

3 pin direct to power board two jacks on the power input.  The fans appear to daisy chain four push five pull.

[felix73]

Hello!
how to enter the BIOS boot pandaminer?
that would put the switch on when power on?
enter the BIOS  pandaminer
when you push the start button
Hold on delete key

[theghost1980]

Some more results.

So XMR still at 4amps (880watt) after 15hrs.

Picture:



Also did a quick testrun on ethereum using the latest available Claymore miner (bad comparison vs Windows as the latest release there is newer and faster, i tested this and it is faster..)
I will test with genoil's as well later today.
236Mh while consuming 5.3A (1166watt) most consumption i've seen as of now..

Picture:



Did a testrun for zcash as well.
1730H while consuming 4.9A (1078watt)

Picture:



Then i did some minor modifcations (rom wise)  
Improved hashrate and same consumption.
So still 4A (880 watt) but this time hitting 6400h  

Picture:




Again, overall, i must say, awesome machine.

This could be seriously interesting for bigger farms.
I made it so that i just plug in the power, it boots and starts mining.
Other algo, no problem. Switch and go.

Greetings!

Hi there. Thank you so much for your posts, that's very good info. may I ask, how is working the system so far? It's been a couple of months since you got it right?

Basically let me know what do you think, is very stable? is worth for buying?
Besides XMR / ETH/ ZAC, is there any other cripto you've been able to mine as well?

Thanks in advance for your info!

[megax05]

@Eliovp can you provide a copy of the bios on those GPUs I see they use Hynix memory and I am interested on the timing on those.

[dagarair]

Some more results.

So XMR still at 4amps (880watt) after 15hrs.

Picture:



Also did a quick testrun on ethereum using the latest available Claymore miner (bad comparison vs Windows as the latest release there is newer and faster, i tested this and it is faster..)
I will test with genoil's as well later today.
236Mh while consuming 5.3A (1166watt) most consumption i've seen as of now..

Picture:



Did a testrun for zcash as well.
1730H while consuming 4.9A (1078watt)

Picture:



Then i did some minor modifcations (rom wise)  
Improved hashrate and same consumption.
So still 4A (880 watt) but this time hitting 6400h  

Picture:




Again, overall, i must say, awesome machine.

This could be seriously interesting for bigger farms.
I made it so that i just plug in the power, it boots and starts mining.
Other algo, no problem. Switch and go.

Greetings!

Hi there. Thank you so much for your posts, that's very good info. may I ask, how is working the system so far? It's been a couple of months since you got it right?

Basically let me know what do you think, is very stable? is worth for buying?
Besides XMR / ETH/ ZAC, is there any other cripto you've been able to mine as well?

Thanks in advance for your info!

Running like a champ.  I have a few pandas and run XMR.  I am about 6400 (800 a card ish) and sub 900 watts.  I also had him write me one for my RX 6 card rigs and I am getting 4.5K on 640 watts! 

[dagarair]

@Eliovp can you provide a copy of the bios on those GPUs I see they use Hynix memory and I am interested on the timing on those.

Yeah he'll provide a copy once you buy it.  lol

[viramarket]

Is in this chat people who use the program Simplemining on Panda the miner B3+ ?

[dagarair]

it will work on simple mining no problem