Looking for Help with Multiple Graphics Card Setup in Xubuntu 12.10 for Bitcoin

theonlineanswer (OP)

Newbie

Offline

Activity: 5
Merit: 0

Looking for Help with Multiple Graphics Card Setup in Xubuntu 12.10 for Bitcoin

April 22, 2013, 08:03:27 PM
Last edit: April 22, 2013, 08:10:39 PM by tysat

#1

This is an attempt to provide as much information about the situation that I can to successfully resolve the issues and get to mining bitcoin.

I am desperately attempting to get away from Windows (my comfort zone) and use linux for this endeavor. I am by no means knowledgeable in Linux. So far, I have spent about 20 hours trying to search online for solutions to this issue. I think I am getting close to figuring out the issue but I am also running out of ideas to try. I hope that by providing all the below information will give someone enough information to tell me what I am missing.

Not mentioned in this very long support thread is that I tried the new AMD 13.1 drivers (on a clean Xubuntu installation) and I tried the 13 beta drivers as well. When I used these drivers, I could not mine at all on either card. The error that I received was that there were no openCL gpu's available. Below, includes partial successes.

For the full set of the information, I created a .pdf - with logs, screenshots, the kitchen sink. It's a google doc with commenting turned on.

https://docs.google.com/file/d/0B9MiAgGtDs3BTHdib3ozaFBaa2s/edit?usp=sharing

Blarg, this is my first post... I realize the newbie section is probably not where this belongs and I hope someone will find it and give a girl some help.

Thanks
Shannon

Looking for Help with Multiple Graphics Card Setup in Xubuntu 12.10 for Bitcoin Mining

This is an attempt to provide as much information about the situation that I can to successfully resolve the issues and get to mining bitcoin.

I am desperately attempting to get away from Windows (my comfort zone) and use linux for this endeavour. I am by no means knowledgeable in Linux. So far, I have spent about 20 hours trying to search online for solutions to this issue. I think I am getting close to figuring out the issue but I am also running out of ideas to try. I hope that by providing all the below information will give someone enough information to tell me what I am missing.

Not mentioned in this very long support thread is that I tried the new AMD 13.1 drivers (on a clean Xubuntu installation) and I tried the 13 beta drivers as well. When I used these drivers, I could not mine at all on either card. The error that I received was that there were no openCL gpu's available. Below, includes partial successes.

System Information

Distributor ID: Ubuntu
Description: Ubuntu 12.10
Release: 12.10
Codename: quantal
Xcfe Version 4.10, distro Xubuntu

MSI 970A-G46 9 Series AM3+ Motherboard
PNY 4096MB PC10666 DDR3 1333MHz x 2
EVGA 120-PB-0750-KR Super NOVA Power Supply
Seagate Hard Drive (SATA)
ASUS® 8x External Slim DVD+/-RW Drive
VisionTek Radeon HD 6950 1GB GDDR5 PCIe
HIS Radeon HD 7950 IceQ X2 Boost Clock 3GB PCI-E w/ DVI, HDMI, Dual DP

To verify that the second pcie slot was working properly, I ran sudo lshw|less. This is the results:

(I apologize upfront... I am not sure how much of this is relevant to troubleshooting and I'd rather give too much than not enough.)

Hardware Information via Xubuntu

Code:

        *-pci:0
             description: PCI bridge
             product: RD890 PCI to PCI bridge (PCI express gpp port B)
             vendor: Advanced Micro Devices [AMD] nee ATI
             physical id: 2
             bus info: pci@0000:00:02.0
             version: 00
             width: 32 bits
             clock: 33MHz
             capabilities: pci pm pciexpress msi ht normal_decode bus_master cap_list
             configuration: driver=pcieport
             resources: irq:52 ioport:e000(size=4096) memory:fea00000-feafffff ioport:d0000000(size=268435456)
           *-display
                description: VGA compatible controller
                product: Tahiti PRO [Radeon HD 7950]
                vendor: Advanced Micro Devices [AMD] nee ATI
                physical id: 0
                bus info: pci@0000:01:00.0
                version: 00
                width: 64 bits
                clock: 33MHz
                capabilities: pm pciexpress msi vga_controller bus_master cap_list rom
                configuration: driver=fglrx_pci latency=0
                resources: irq:82 memory:d0000000-dfffffff memory:fea00000-fea3ffff ioport:e000(size=256) memory:fea40000-fea5ffff
           *-multimedia
                description: Audio device
                product: Tahiti XT HDMI Audio [Radeon HD 7970 Series]
                vendor: Advanced Micro Devices [AMD] nee ATI
                physical id: 0.1
                bus info: pci@0000:01:00.1
                version: 00
                width: 64 bits
                clock: 33MHz
                capabilities: pm pciexpress msi bus_master cap_list
                configuration: driver=snd_hda_intel latency=0
                resources: irq:79 memory:fea60000-fea63fff
        *-pci:1
             description: PCI bridge
             product: RD890 PCI to PCI bridge (PCI express gpp port C)
             vendor: Advanced Micro Devices [AMD] nee ATI
             physical id: 3
             bus info: pci@0000:00:03.0
             version: 00
             width: 32 bits
             clock: 33MHz
             capabilities: pci pm pciexpress msi ht normal_decode bus_master cap_list
             configuration: driver=pcieport
             resources: irq:52 ioport:d000(size=4096) memory:fe900000-fe9fffff ioport:c0000000(size=268435456)
           *-display
                description: VGA compatible controller
                product: Cayman PRO [Radeon HD 6950]
                vendor: Advanced Micro Devices [AMD] nee ATI
                physical id: 0
                bus info: pci@0000:02:00.0
                version: 00
                width: 64 bits
                clock: 33MHz
                capabilities: pm pciexpress msi vga_controller bus_master cap_list rom
                configuration: driver=fglrx_pci latency=0
                resources: irq:81 memory:c0000000-cfffffff memory:fe920000-fe93ffff ioport:d000(size=256) memory:fe900000-fe91ffff
           *-multimedia
                description: Audio device
                product: Cayman/Antilles HDMI Audio [Radeon HD 6900 Series]
                vendor: Advanced Micro Devices [AMD] nee ATI
                physical id: 0.1
                bus info: pci@0000:02:00.1
                version: 00
                width: 64 bits
                clock: 33MHz
                capabilities: pm pciexpress msi bus_master cap_list
                configuration: driver=snd_hda_intel latency=0
                resources: irq:80 memory:fe940000-fe943fff
        *-pci:2
             description: PCI bridge
             product: RD890 PCI to PCI bridge (PCI express gpp port D)
             vendor: Advanced Micro Devices [AMD] nee ATI
             physical id: 4
             bus info: pci@0000:00:04.0
             version: 00
             width: 32 bits
             clock: 33MHz
             capabilities: pci pm pciexpress msi ht normal_decode bus_master cap_list
             configuration: driver=pcieport
             resources: irq:52 memory:fe800000-fe8fffff

Installation Process
To date, I have reinstalled Xubuntu entirely erasing the previous version over ten times now with varying setups to try to get cgminer / bitminter to recognize both cards using OpenCL. Also, I tried Fedora and Mint Linux w/ Cinnamon and had varying success / failures.

The one constant variable through out all of the installations is that I could get either card to work successfully using bitminter with their appropriate hash rate. I just could not get both the 7950 AND the 6950 to work at the same time.

For the original installation process, I started with a guide that I found online titled, Complete Guide To Mine Bitcoin on Xubuntu 12.04.

Since one of the cards is a 7xxx series card, I used the driver instructions for the 7xxx series.

These instructions gave me 1 working video card for mining. Note: It didn't matter if put the 6950 in the first pcie slot on the motherboard or the 7950 - this setup would find each of them, give me the correct information about the card, and allow me to hash in bitminter. However, bitminter would only find 1 gpu using openCL at a time.

In the beginning of this process, I used sudo amdcccle to open the Catalyst Control Panel, it would only display 1 video card. Again, depending on what was in the first pcie slot would determine, which that would display.

Then, I checked the xorg.conf file located in /etc/X11. Originally, in this file, it only displayed one "device" section, which referred to the first pcie slot. However, I tried a couple times to add the second screen, monitor and device with no success (wouldn't even boot into xfce) - command line.

This is when I installed Mint Linux w/ Cinnamon. I followed the directions for installing the drivers in the above bitcoin guide and Mint Linux actually worked as a dual monitor setup - displaying information on both screens. HOWEVER, it also displayed this information repeatedly on 3 virtual desktops.

Again, I could mine using bitminter on ONE gpu - not both.

Here's the xorg.conf file:

Code:

Section "ServerLayout"
    Identifier     "aticonfig Layout"
    Screen      0  "aticonfig-Screen[0]-0" 0 0
    Screen         "aticonfig-Screen[1]-0" RightOf "aticonfig-Screen[0]-0"
EndSection

Section "Module"
EndSection

Section "ServerFlags"
    Option        "Xinerama" "on"
EndSection

Section "Monitor"
    Identifier   "aticonfig-Monitor[0]-0"
    Option        "VendorName" "ATI Proprietary Driver"
    Option        "ModelName" "Generic Autodetecting Monitor"
    Option        "DPMS" "true"
EndSection

Section "Monitor"
    Identifier   "aticonfig-Monitor[1]-0"
    Option        "VendorName" "ATI Proprietary Driver"
    Option        "ModelName" "Generic Autodetecting Monitor"
    Option        "DPMS" "true"
EndSection

Section "Device"
    Identifier  "aticonfig-Device[0]-0"
    Driver      "fglrx"
    BusID       "PCI:1:0:0"
EndSection

Section "Device"
    Identifier  "aticonfig-Device[1]-0"
    Driver      "fglrx"
    BusID       "PCI:2:0:0"
EndSection

Section "Screen"
    Identifier "aticonfig-Screen[0]-0"
    Device     "aticonfig-Device[0]-0"
    Monitor    "aticonfig-Monitor[0]-0"
    DefaultDepth     24
    SubSection "Display"
        Viewport   0 0
        Depth     24
    EndSubSection
EndSection

Section "Screen"
    Identifier "aticonfig-Screen[1]-0"
    Device     "aticonfig-Device[1]-0"
    Monitor    "aticonfig-Monitor[1]-0"
    DefaultDepth     24
    SubSection "Display"
        Viewport   0 0
        Depth     24
    EndSubSection
EndSection

After looking at this xorg.conf file, it seemed to have the correct information that I was trying to put into the one on Xubuntu. I copied this file. I reinstalled Xubuntu (erasing previous version), installed the updates, followed the bitcoin setup guide above and then added this modified xorg.conf file to the /etc/X11 folder. Rebooted. Also, during reboot, there were video errors that scrolled too fast to read the exact info. So, again partial success / failure.

Here's the Xorg Log:

Code:

[    12.652] 
X.Org X Server 1.13.0
Release Date: 2012-09-05
[    12.652] X Protocol Version 11, Revision 0
[    12.652] Build Operating System: Linux 3.2.0-37-generic x86_64 Ubuntu
[    12.652] Current Operating System: Linux uber 3.5.0-17-generic #28-Ubuntu SMP Tue Oct 9 19:31:23 UTC 2012 x86_64
[    12.652] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.5.0-17-generic root=UUID=10985092-6bf0-4423-9176-98df1bfadf52 ro quiet splash
[    12.652] Build Date: 11 April 2013  12:53:36PM
[    12.652] xorg-server 2:1.13.0-0ubuntu6.2 (For technical support please see http://www.ubuntu.com/support) 
[    12.652] Current version of pixman: 0.26.0
[    12.652]     Before reporting problems, check http://wiki.x.org
    to make sure that you have the latest version.
[    12.652] Markers: (--) probed, (**) from config file, (==) default setting,
    (++) from command line, (!!) notice, (II) informational,
    (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[    12.652] (==) Log file: "/var/log/Xorg.0.log", Time: Mon Apr 22 10:54:55 2013
[    12.652] (==) Using config file: "/etc/X11/xorg.conf"
[    12.652] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[    12.653] (==) ServerLayout "aticonfig Layout"
[    12.653] (**) |-->Screen "aticonfig-Screen[0]-0" (0)
[    12.653] (**) |   |-->Monitor "aticonfig-Monitor[0]-0"
[    12.653] (**) |   |-->Device "aticonfig-Device[0]-0"
[    12.653] (**) |-->Screen "aticonfig-Screen[1]-0" (1)
[    12.653] (**) |   |-->Monitor "aticonfig-Monitor[1]-0"
[    12.653] (**) |   |-->Device "aticonfig-Device[1]-0"
[    12.653] (**) Option "Xinerama" "on"
[    12.653] (==) Automatically adding devices
[    12.653] (==) Automatically enabling devices
[    12.653] (==) Automatically adding GPU devices
[    12.653] (**) Xinerama: enabled
[    12.653] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
[    12.653]     Entry deleted from font path.
[    12.653] (WW) The directory "/usr/share/fonts/X11/100dpi/" does not exist.
[    12.653]     Entry deleted from font path.
[    12.653] (WW) The directory "/usr/share/fonts/X11/75dpi/" does not exist.
[    12.653]     Entry deleted from font path.
[    12.653] (WW) The directory "/usr/share/fonts/X11/100dpi" does not exist.
[    12.653]     Entry deleted from font path.
[    12.653] (WW) The directory "/usr/share/fonts/X11/75dpi" does not exist.
[    12.653]     Entry deleted from font path.
[    12.653] (WW) The directory "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType" does not exist.
[    12.653]     Entry deleted from font path.
[    12.653] (==) FontPath set to:
    /usr/share/fonts/X11/misc,
    /usr/share/fonts/X11/Type1,
    built-ins
[    12.653] (==) ModulePath set to "/usr/lib/x86_64-linux-gnu/xorg/extra-modules,/usr/lib/xorg/extra-modules,/usr/lib/xorg/modules"
[    12.653] (II) The server relies on udev to provide the list of input devices.
    If no devices become available, reconfigure udev or disable AutoAddDevices.
[    12.653] (II) Loader magic: 0x7ffd2abb5c40
[    12.653] (II) Module ABI versions:
[    12.653]     X.Org ANSI C Emulation: 0.4
[    12.653]     X.Org Video Driver: 13.0
[    12.653]     X.Org XInput driver : 18.0
[    12.653]     X.Org Server Extension : 7.0
[    12.655] (--) PCI:*(0:1:0:0) 1002:679a:1787:201c rev 0, Mem @ 0xd0000000/268435456, 0xfea00000/262144, I/O @ 0x0000e000/256, BIOS @ 0x????????/131072
[    12.655] (--) PCI: (0:2:0:0) 1002:6719:1545:6950 rev 0, Mem @ 0xc0000000/268435456, 0xfe920000/131072, I/O @ 0x0000d000/256, BIOS @ 0x????????/131072
Removed Part of the log - limit of forum - full version in pdf
[    12.655] (II) LoadModule: "glx"
[    12.655] (II) Loading /usr/lib/x86_64-linux-gnu/xorg/extra-modules/modules/extensions/libglx.so
[    12.655] (II) Module glx: vendor="Advanced Micro Devices, Inc."
[    12.656]     compiled for 6.9.0, module version = 1.0.0
[    12.656] Loading extension GLX
[    12.656] (II) LoadModule: "fglrx"
[    12.672] (II) Loading /usr/lib/x86_64-linux-gnu/xorg/extra-modules/modules/drivers/fglrx_drv.so
[    12.684] (II) Module fglrx: vendor="FireGL - AMD Technologies Inc."
[    12.684]     compiled for 1.4.99.906, module version = 9.0.2
[    12.685]     Module class: X.Org Video Driver
[    12.685] (II) Loading sub module "fglrxdrm"
[    12.685] (II) LoadModule: "fglrxdrm"
[    12.685] (II) Loading /usr/lib/x86_64-linux-gnu/xorg/extra-modules/modules/linux/libfglrxdrm.so
[    12.685] (II) Module fglrxdrm: vendor="FireGL - AMD Technologies Inc."
[    12.685]     compiled for 1.4.99.906, module version = 9.0.2
[    12.685] (II) AMD Proprietary Linux Driver Version Identifier:9.00.2
[    12.685] (II) AMD Proprietary Linux Driver Release Identifier: 9.00.11                              
[    12.685] (II) AMD Proprietary Linux Driver Build Date: Sep 20 2012 11:56:16
[    12.685] (++) using VT number 7

[    12.686] (WW) Falling back to old probe method for fglrx
[    12.689] (II) Loading PCS database from /etc/ati/amdpcsdb /etc/ati/amdpcsdb.default
[    12.701] ukiDynamicMajor: found major device number 250
[    12.701] ukiDynamicMajor: found major device number 250
[    12.701] ukiOpenByBusid: Searching for BusID PCI:1:0:0
[    12.701] ukiOpenDevice: node name is /dev/ati/card0
[    12.701] ukiOpenDevice: open result is 10, (OK)
[    13.046] ukiOpenByBusid: ukiOpenMinor returns 10
[    13.046] ukiOpenByBusid: ukiGetBusid reports PCI:2:0:0
[    13.046] ukiOpenDevice: node name is /dev/ati/card1
[    13.086] ukiOpenDevice: open result is 10, (OK)
[    13.086] ukiOpenByBusid: ukiOpenMinor returns 10
[    13.086] ukiOpenByBusid: ukiGetBusid reports PCI:1:0:0
[    13.086] ukiDynamicMajor: found major device number 250
[    13.086] ukiDynamicMajor: found major device number 250
[    13.086] ukiOpenByBusid: Searching for BusID PCI:2:0:0
[    13.086] ukiOpenDevice: node name is /dev/ati/card0
[    13.086] ukiOpenDevice: open result is 10, (OK)
[    13.086] ukiOpenByBusid: ukiOpenMinor returns 10
[    13.086] ukiOpenByBusid: ukiGetBusid reports PCI:2:0:0
[    13.087] (--) Chipset Supported AMD Graphics Processor (0x679A) found
[    13.087] (--) Chipset Supported AMD Graphics Processor (0x6719) found
[    13.087] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:0:0) found
[    13.087] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:0:2) found
[    13.087] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:2:0) found
[    13.087] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:3:0) found
[    13.087] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:4:0) found
[    13.087] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:17:0) found
[    13.087] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:18:0) found
[    13.087] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:18:2) found
[    13.087] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:19:0) found
[    13.087] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:19:2) found
[    13.087] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:20:0) found
[    13.087] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:20:1) found
[    13.087] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:20:2) found
[    13.087] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:20:3) found
[    13.087] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:20:4) found
[    13.087] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:20:5) found
[    13.087] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:21:0) found
[    13.087] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:22:0) found
[    13.087] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:22:2) found
[    13.087] (WW) fglrx: No matching Device section for instance (BusID PCI:0@1:0:1) found
[    13.087] (WW) fglrx: No matching Device section for instance (BusID PCI:0@2:0:1) found
[    13.088] (II) AMD Video driver is running on a device belonging to a group targeted for this release
[    13.088] (II) AMD Video driver is signed
[    13.088] (II) fglrx(0): pEnt->device->identifier=0x7ffd2b5994f0
[    13.088] (II) fglrx(1): pEnt->device->identifier=0x7ffd2b599800
[    13.088] (II) fglrx(0): === [xdl_xs113_atiddxPreInit] === begin
[    13.088] (II) Loading sub module "vgahw"
[    13.088] (II) LoadModule: "vgahw"
[    13.110] (II) Loading /usr/lib/xorg/modules/libvgahw.so
[    13.110] (II) Module vgahw: vendor="X.Org Foundation"
[    13.110]     compiled for 1.13.0, module version = 0.1.0
[    13.110]     ABI class: X.Org Video Driver, version 13.0
[    13.110] (**) fglrx(0): Depth 24, (--) framebuffer bpp 32
[    13.110] (II) fglrx(0): Pixel depth = 24 bits stored in 4 bytes (32 bpp pixmaps)
[    13.110] (==) fglrx(0): Default visual is TrueColor
[    13.110] (**) fglrx(0): Option "DPMS" "true"
[    13.110] (==) fglrx(0): RGB weight 888
[    13.110] (II) fglrx(0): Using 8 bits per RGB 
[    13.110] (==) fglrx(0): Buffer Tiling is ON
[    13.110] (II) Loading sub module "fglrxdrm"
[    13.110] (II) LoadModule: "fglrxdrm"
[    13.110] (II) Loading /usr/lib/x86_64-linux-gnu/xorg/extra-modules/modules/linux/libfglrxdrm.so
[    13.110] (II) Module fglrxdrm: vendor="FireGL - AMD Technologies Inc."
[    13.110]     compiled for 1.4.99.906, module version = 9.0.2
[    13.121] ukiDynamicMajor: found major device number 250
[    13.121] ukiDynamicMajor: found major device number 250
[    13.121] ukiOpenByBusid: Searching for BusID PCI:1:0:0
[    13.121] ukiOpenDevice: node name is /dev/ati/card0
[    13.121] ukiOpenDevice: open result is 14, (OK)
[    13.121] ukiOpenByBusid: ukiOpenMinor returns 14
[    13.121] ukiOpenByBusid: ukiGetBusid reports PCI:2:0:0
[    13.121] ukiOpenDevice: node name is /dev/ati/card1
[    13.121] ukiOpenDevice: open result is 14, (OK)
[    13.121] ukiOpenByBusid: ukiOpenMinor returns 14
[    13.121] ukiOpenByBusid: ukiGetBusid reports PCI:1:0:0
[    13.121] (**) fglrx(0): NoAccel = NO
[    13.121] (**) fglrx(0): AMD 2D Acceleration Architecture enabled
[    13.121] (--) fglrx(0): Chipset: "AMD Radeon HD 7900 Series " (Chipset = 0x679a)
[    13.121] (--) fglrx(0): (PciSubVendor = 0x1787, PciSubDevice = 0x201c)
[    13.121] (==) fglrx(0): board vendor info: third party graphics adapter - NOT original AMD
[    13.121] (--) fglrx(0): Linear framebuffer (phys) at 0xd0000000
[    13.121] (--) fglrx(0): MMIO registers at 0xfea00000
[    13.121] (--) fglrx(0): I/O port at 0x0000e000
[    13.121] (==) fglrx(0): ROM-BIOS at 0x000c0000
[    13.122] (II) fglrx(0): AC Adapter is used
[    13.122] (II) fglrx(0): Primary V_BIOS segment is: 0xc000
[    13.212] (II) Loading sub module "vbe"
[    13.212] (II) LoadModule: "vbe"
[    13.212] (II) Loading /usr/lib/xorg/modules/libvbe.so
[    13.212] (II) Module vbe: vendor="X.Org Foundation"
[    13.212]     compiled for 1.13.0, module version = 1.1.0
[    13.212]     ABI class: X.Org Video Driver, version 13.0
[    13.212] (II) fglrx(0): VESA BIOS detected
[    13.212] (II) fglrx(0): VESA VBE Version 3.0
[    13.212] (II) fglrx(0): VESA VBE Total Mem: 16384 kB
[    13.212] (II) fglrx(0): VESA VBE OEM: AMD ATOMBIOS
[    13.212] (II) fglrx(0): VESA VBE OEM Software Rev: 15.30
[    13.212] (II) fglrx(0): VESA VBE OEM Vendor: (C) 1988-2010, Advanced Micro Devices, Inc.
[    13.212] (II) fglrx(0): VESA VBE OEM Product: TAHITI
[    13.212] (II) fglrx(0): VESA VBE OEM Product Rev: 01.00
[    13.212] (II) fglrx(0): AMD Video BIOS revision 9 or later detected
[    13.212] (--) fglrx(0): Video RAM: 3145728 kByte, Type: GDDR5
[    13.212] (II) fglrx(0): PCIE card detected
[    13.213] (--) fglrx(0): Using per-process page tables (PPPT) as GART.
[    13.213] (WW) fglrx(0): board is an unknown third party board, chipset is supported
[    13.213] (II) fglrx(0): [FB] MC range(MCFBBase = 0xf400000000, MCFBSize = 0xc0000000)
[    13.213] (II) fglrx(0): RandR 1.2 support is enabled!
[    13.213] (II) fglrx(0): RandR 1.2 rotation support is enabled!
[    13.213] (==) fglrx(0): Center Mode is disabled 
[    13.213] (II) Loading sub module "fb"
[    13.213] (II) LoadModule: "fb"
[    13.213] (II) Loading /usr/lib/xorg/modules/libfb.so
[    13.213] (II) Module fb: vendor="X.Org Foundation"
[    13.213]     compiled for 1.13.0, module version = 1.0.0
[    13.213]     ABI class: X.Org ANSI C Emulation, version 0.4
[    13.213] (II) Loading sub module "ddc"
[    13.213] (II) LoadModule: "ddc"
[    13.213] (II) Module "ddc" already built-in
[    13.298] (II) fglrx(0): Output DFP1 using monitor section aticonfig-Monitor[0]-0
[    13.298] (II) fglrx(0): Output DFP2 has no monitor section
[    13.298] (II) fglrx(0): Output DFP3 has no monitor section
[    13.298] (II) fglrx(0): Output DFP4 has no monitor section
[    13.298] (II) fglrx(0): Output DFP5 has no monitor section
[    13.298] (II) fglrx(0): Output DFP6 has no monitor section
[    13.298] (II) fglrx(0): Output DFP7 has no monitor section
[    13.298] (II) fglrx(0): Output DFP8 has no monitor section
[    13.298] (II) fglrx(0): Output DFP9 has no monitor section
[    13.298] (II) fglrx(0): Output DFP10 has no monitor section
[    13.298] (II) fglrx(0): Output CRT1 has no monitor section
[    13.298] (II) Loading sub module "ddc"
[    13.298] (II) LoadModule: "ddc"
[    13.298] (II) Module "ddc" already built-in
[    13.298] (II) fglrx(0): Connected Display0: CRT1
[    13.298] (II) fglrx(0):  Display0: Failed to get EDID information. 
[    13.299] (II) fglrx(0): EDID for output DFP1
[    13.299] (II) fglrx(0): EDID for output DFP2
[    13.299] (II) fglrx(0): EDID for output DFP3
[    13.299] (II) fglrx(0): EDID for output DFP4
[    13.299] (II) fglrx(0): EDID for output DFP5
[    13.299] (II) fglrx(0): EDID for output DFP6
[    13.299] (II) fglrx(0): EDID for output DFP7
[    13.299] (II) fglrx(0): EDID for output DFP8
[    13.299] (II) fglrx(0): EDID for output DFP9
[    13.299] (II) fglrx(0): EDID for output DFP10
[    13.299] (II) fglrx(0): EDID for output CRT1
[    13.299] (II) fglrx(0): Manufacturer: SAM  Model: 124  Serial#: 1296707895
[    13.299] (II) fglrx(0): Year: 2004  Week: 32
[    13.299] (II) fglrx(0): EDID Version: 1.3
[    13.299] (II) fglrx(0): Analog Display Input,  Input Voltage Level: 0.700/0.700 V
[    13.299] (II) fglrx(0): Sync:  Separate  Composite
[    13.299] (II) fglrx(0): Max Image Size [cm]: horiz.: 34  vert.: 27
[    13.299] (II) fglrx(0): Gamma: 2.20
[    13.299] (II) fglrx(0): DPMS capabilities: Off; RGB/Color Display
[    13.299] (II) fglrx(0): First detailed timing is preferred mode
[    13.299] (II) fglrx(0): redX: 0.650 redY: 0.330   greenX: 0.330 greenY: 0.600
[    13.299] (II) fglrx(0): blueX: 0.150 blueY: 0.080   whiteX: 0.313 whiteY: 0.329
[    13.299] (II) fglrx(0): Supported established timings:
[    13.299] (II) fglrx(0): 720x400@70Hz
[    13.299] (II) fglrx(0): 640x480@60Hz
[    13.299] (II) fglrx(0): 640x480@67Hz
[    13.299] (II) fglrx(0): 640x480@72Hz
[    13.299] (II) fglrx(0): 640x480@75Hz
[    13.299] (II) fglrx(0): 800x600@56Hz
[    13.299] (II) fglrx(0): 800x600@60Hz
[    13.299] (II) fglrx(0): 800x600@72Hz
[    13.299] (II) fglrx(0): 800x600@75Hz
[    13.299] (II) fglrx(0): 832x624@75Hz
[    13.299] (II) fglrx(0): 1024x768@60Hz
[    13.299] (II) fglrx(0): 1024x768@70Hz
[    13.299] (II) fglrx(0): 1024x768@75Hz
[    13.299] (II) fglrx(0): 1280x1024@75Hz
[    13.299] (II) fglrx(0): 1152x864@75Hz
[    13.299] (II) fglrx(0): Manufacturer's mask: 0
[    13.299] (II) fglrx(0): Supported standard timings:
[    13.299] (II) fglrx(0): #0: hsize: 1280  vsize 1024  refresh: 60  vid: 32897
[    13.299] (II) fglrx(0): #1: hsize: 1152  vsize 864  refresh: 75  vid: 20337
[    13.299] (II) fglrx(0): Supported detailed timing:
[    13.299] (II) fglrx(0): clock: 108.0 MHz   Image Size:  338 x 270 mm
[    13.299] (II) fglrx(0): h_active: 1280  h_sync: 1328  h_sync_end 1440 h_blank_end 1688 h_border: 0
[    13.299] (II) fglrx(0): v_active: 1024  v_sync: 1025  v_sync_end 1028 v_blanking: 1066 v_border: 0
[    13.299] (II) fglrx(0): Ranges: V min: 56 V max: 75 Hz, H min: 30 H max: 81 kHz, PixClock max 145 MHz
[    13.299] (II) fglrx(0): Monitor name: SyncMaster
[    13.299] (II) fglrx(0): Serial No: HCJX807028
[    13.299] (II) fglrx(0): EDID (in hex):
[    13.299] (II) fglrx(0):     00ffffffffffff004c2d240137314a4d
[    13.299] (II) fglrx(0):     200e01036c221b782aaaa5a654549926
[    13.299] (II) fglrx(0):     145054bfef808180714f010101010101
[    13.299] (II) fglrx(0):     010101010101302a009851002a403070
[    13.299] (II) fglrx(0):     1300520e1100001e000000fd00384b1e
[    13.299] (II) fglrx(0):     510e000a202020202020000000fc0053
[    13.299] (II) fglrx(0):     796e634d61737465720a2020000000ff
[    13.299] (II) fglrx(0):     0048434a583830373032380a20200029
[    13.299] (II) fglrx(0): Printing probed modes for output CRT1
[    13.299] (II) fglrx(0): Modeline "1280x1024"x60.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz eP)
[    13.299] (II) fglrx(0): Modeline "1280x1024"x75.0  135.00  1280 1296 1440 1688  1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[    13.299] (II) fglrx(0): Modeline "1280x960"x75.0  135.00  1280 1296 1440 1688  960 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[    13.299] (II) fglrx(0): Modeline "1280x960"x60.0  108.00  1280 1328 1440 1688  960 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[    13.299] (II) fglrx(0): Modeline "1152x864"x75.0  108.00  1152 1216 1344 1600  864 865 868 900 +hsync +vsync (67.5 kHz e)
[    13.299] (II) fglrx(0): Modeline "1152x864"x60.0  108.00  1152 1328 1440 1688  864 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[    13.299] (II) fglrx(0): Modeline "1280x768"x75.0  135.00  1280 1296 1440 1688  768 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[    13.299] (II) fglrx(0): Modeline "1280x768"x60.0  108.00  1280 1328 1440 1688  768 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[    13.299] (II) fglrx(0): Modeline "1280x720"x75.0  135.00  1280 1296 1440 1688  720 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[    13.299] (II) fglrx(0): Modeline "1280x720"x60.0  108.00  1280 1328 1440 1688  720 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[    13.299] (II) fglrx(0): Modeline "1024x768"x75.0   78.75  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.0 kHz e)
[    13.299] (II) fglrx(0): Modeline "1024x768"x70.0   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync (56.5 kHz e)
[    13.299] (II) fglrx(0): Modeline "1024x768"x60.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz e)
[    13.299] (II) fglrx(0): Modeline "800x600"x72.0   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync (48.1 kHz e)
[    13.299] (II) fglrx(0): Modeline "800x600"x75.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync (46.9 kHz e)
[    13.299] (II) fglrx(0): Modeline "800x600"x60.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz e)
[    13.299] (II) fglrx(0): Modeline "800x600"x56.0   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz e)
[    13.299] (II) fglrx(0): Modeline "640x480"x75.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz e)
[    13.299] (II) fglrx(0): Modeline "640x480"x72.0   31.50  640 656 696 832  480 481 484 520 -hsync -vsync (37.9 kHz e)
[    13.299] (II) fglrx(0): Modeline "640x480"x67.0   27.28  640 664 728 816  480 481 484 499 -hsync +vsync (33.4 kHz e)
[    13.299] (II) fglrx(0): Modeline "640x480"x60.0   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz e)
[    13.299] (II) fglrx(0): Output DFP1 disconnected
[    13.299] (II) fglrx(0): Output DFP2 disconnected
[    13.299] (II) fglrx(0): Output DFP3 disconnected
[    13.299] (II) fglrx(0): Output DFP4 disconnected
[    13.299] (II) fglrx(0): Output DFP5 disconnected
[    13.299] (II) fglrx(0): Output DFP6 disconnected
[    13.299] (II) fglrx(0): Output DFP7 disconnected
[    13.299] (II) fglrx(0): Output DFP8 disconnected
[    13.299] (II) fglrx(0): Output DFP9 disconnected
[    13.299] (II) fglrx(0): Output DFP10 disconnected
[    13.299] (II) fglrx(0): Output CRT1 connected
[    13.299] (II) fglrx(0): Using exact sizes for initial modes
[    13.299] (II) fglrx(0): Output CRT1 using initial mode 1280x1024
[    13.299] (II) fglrx(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[    13.299] (II) fglrx(0): DPI set to (96, 96)
[    13.299] (II) fglrx(0): Eyefinity capable adapter detected.
[    13.299] (II) fglrx(0): Adapter AMD Radeon HD 7900 Series  has 6 configurable heads and 1 displays connected.
[    13.299] (==) fglrx(0):  PseudoColor visuals disabled
[    13.299] (II) Loading sub module "ramdac"
[    13.299] (II) LoadModule: "ramdac"
[    13.299] (II) Module "ramdac" already built-in
[    13.299] (==) fglrx(0): NoDRI = NO
[    13.299] (==) fglrx(0): Capabilities: 0x00000000
[    13.299] (==) fglrx(0): CapabilitiesEx: 0x00000000
[    13.299] (==) fglrx(0): OpenGL ClientDriverName: "fglrx_dri.so"
[    13.299] (==) fglrx(0): UseFastTLS=0
[    13.299] (II) fglrx(0): Desktop Vsync is enabled.
[    13.299] (II) fglrx(0): Shadow Primary option: ShadowPrimary is enabled
[    13.300] (II) fglrx(1): === [xdl_xs113_atiddxPreInit] === begin
[    13.300] (**) fglrx(1): Depth 24, (--) framebuffer bpp 32
[    13.300] (II) fglrx(1): Pixel depth = 24 bits stored in 4 bytes (32 bpp pixmaps)
[    13.300] (==) fglrx(1): Default visual is TrueColor
[    13.300] (**) fglrx(1): Option "DPMS" "true"
[    13.300] (==) fglrx(1): RGB weight 888
[    13.300] (II) fglrx(1): Using 8 bits per RGB 
[    13.300] (==) fglrx(1): Buffer Tiling is ON
[    13.300] (II) Loading sub module "fglrxdrm"
[    13.300] (II) LoadModule: "fglrxdrm"
[    13.300] (II) Loading /usr/lib/x86_64-linux-gnu/xorg/extra-modules/modules/linux/libfglrxdrm.so
[    13.300] (II) Module fglrxdrm: vendor="FireGL - AMD Technologies Inc."
[    13.300]     compiled for 1.4.99.906, module version = 9.0.2
[    13.311] ukiDynamicMajor: found major device number 250
[    13.311] ukiDynamicMajor: found major device number 250
[    13.311] ukiOpenByBusid: Searching for BusID PCI:2:0:0
[    13.312] ukiOpenDevice: node name is /dev/ati/card0
[    13.312] ukiOpenDevice: open result is 15, (OK)
[    13.312] ukiOpenByBusid: ukiOpenMinor returns 15
[    13.312] ukiOpenByBusid: ukiGetBusid reports PCI:2:0:0
[    13.312] (WW) fglrx(1): Unable to register ADL handler for 0x00C00000
[    13.312] (**) fglrx(1): NoAccel = NO
[    13.312] (**) fglrx(1): AMD 2D Acceleration Architecture enabled
[    13.312] (--) fglrx(1): Chipset: "AMD Radeon HD 6900 Series " (Chipset = 0x6719)
[    13.312] (--) fglrx(1): (PciSubVendor = 0x1545, PciSubDevice = 0x6950)
[    13.312] (==) fglrx(1): board vendor info: third party graphics adapter - NOT original AMD
[    13.312] (--) fglrx(1): Linear framebuffer (phys) at 0xc0000000
[    13.312] (--) fglrx(1): MMIO registers at 0xfe920000
[    13.312] (--) fglrx(1): I/O port at 0x0000d000
[    13.312] (==) fglrx(1): ROM-BIOS at 0x000c0000
[    13.312] (II) fglrx(0): AC Adapter is used
[    13.312] (II) fglrx(0): AMD Video BIOS revision 9 or later detected
[    13.312] (--) fglrx(1): Video RAM: 1048576 kByte, Type: GDDR5
[    13.312] (II) fglrx(1): PCIE card detected
[    13.312] (--) fglrx(1): Using per-process page tables (PPPT) as GART.
[    13.312] (WW) fglrx(1): board is an unknown third party board, chipset is supported
[    13.312] (II) fglrx(0): [FB] MC range(MCFBBase = 0xf800000000, MCFBSize = 0x40000000)
[    13.312] (II) fglrx(1): RandR 1.2 support is enabled!
[    13.312] (II) fglrx(1): RandR 1.2 rotation support is enabled!
[    13.312] (==) fglrx(1): Center Mode is disabled 
[    13.312] (II) Loading sub module "fb"
[    13.312] (II) LoadModule: "fb"
[    13.313] (II) Loading /usr/lib/xorg/modules/libfb.so
[    13.313] (II) Module fb: vendor="X.Org Foundation"
[    13.313]     compiled for 1.13.0, module version = 1.0.0
[    13.313]     ABI class: X.Org ANSI C Emulation, version 0.4
[    13.313] (II) Loading sub module "ddc"
[    13.313] (II) LoadModule: "ddc"
[    13.313] (II) Module "ddc" already built-in
[    13.394] (II) fglrx(1): Output DFP1 using monitor section aticonfig-Monitor[1]-0
[    13.394] (II) fglrx(1): Output DFP2 has no monitor section
[    13.394] (II) fglrx(1): Output DFP3 has no monitor section
[    13.394] (II) fglrx(1): Output DFP4 has no monitor section
[    13.394] (II) fglrx(1): Output DFP5 has no monitor section
[    13.394] (II) fglrx(1): Output DFP6 has no monitor section
[    13.394] (II) fglrx(1): Output DFP7 has no monitor section
[    13.394] (II) fglrx(1): Output CRT1 has no monitor section
[    13.394] (II) Loading sub module "ddc"
[    13.394] (II) LoadModule: "ddc"
[    13.394] (II) Module "ddc" already built-in
[    13.394] (II) fglrx(1): Connected Display0: CRT1
[    13.394] (II) fglrx(1):  Display0: Failed to get EDID information. 
[    13.395] (II) fglrx(1): EDID for output DFP1
[    13.395] (II) fglrx(1): EDID for output DFP2
[    13.395] (II) fglrx(1): EDID for output DFP3
[    13.395] (II) fglrx(1): EDID for output DFP4
[    13.395] (II) fglrx(1): EDID for output DFP5
[    13.395] (II) fglrx(1): EDID for output DFP6
[    13.395] (II) fglrx(1): EDID for output DFP7
[    13.395] (II) fglrx(1): EDID for output CRT1
[    13.395] (II) fglrx(1): Manufacturer: DEL  Model: 700e  Serial#: 826553932
[    13.395] (II) fglrx(1): Year: 2005  Week: 17
[    13.395] (II) fglrx(1): EDID Version: 1.3
[    13.395] (II) fglrx(1): Analog Display Input,  Input Voltage Level: 0.700/0.700 V
[    13.395] (II) fglrx(1): Sync:  Separate
[    13.395] (II) fglrx(1): Max Image Size [cm]: horiz.: 38  vert.: 30
[    13.395] (II) fglrx(1): Gamma: 2.20
[    13.395] (II) fglrx(1): DPMS capabilities: Off; RGB/Color Display
[    13.395] (II) fglrx(1): Default color space is primary color space
[    13.395] (II) fglrx(1): First detailed timing is preferred mode
[    13.395] (II) fglrx(1): redX: 0.640 redY: 0.328   greenX: 0.300 greenY: 0.600
[    13.395] (II) fglrx(1): blueX: 0.149 blueY: 0.060   whiteX: 0.312 whiteY: 0.328
[    13.395] (II) fglrx(1): Supported established timings:
[    13.395] (II) fglrx(1): 720x400@70Hz
[    13.395] (II) fglrx(1): 640x480@60Hz
[    13.395] (II) fglrx(1): 640x480@75Hz
[    13.395] (II) fglrx(1): 800x600@60Hz
[    13.395] (II) fglrx(1): 800x600@75Hz
[    13.395] (II) fglrx(1): 1024x768@60Hz
[    13.395] (II) fglrx(1): 1024x768@75Hz
[    13.395] (II) fglrx(1): 1280x1024@75Hz
[    13.395] (II) fglrx(1): Manufacturer's mask: 0
[    13.395] (II) fglrx(1): Supported standard timings:
[    13.395] (II) fglrx(1): #0: hsize: 1152  vsize 864  refresh: 75  vid: 20337
[    13.395] (II) fglrx(1): #1: hsize: 1280  vsize 1024  refresh: 60  vid: 32897
[    13.395] (II) fglrx(1): Supported detailed timing:
[    13.395] (II) fglrx(1): clock: 108.0 MHz   Image Size:  376 x 301 mm
[    13.395] (II) fglrx(1): h_active: 1280  h_sync: 1328  h_sync_end 1440 h_blank_end 1688 h_border: 0
[    13.395] (II) fglrx(1): v_active: 1024  v_sync: 1025  v_sync_end 1028 v_blanking: 1066 v_border: 0
[    13.395] (II) fglrx(1): Serial No: 6418054J1D6L
[    13.395] (II) fglrx(1): Monitor name: DELL E193FP
[    13.395] (II) fglrx(1): Ranges: V min: 56 V max: 76 Hz, H min: 31 H max: 83 kHz, PixClock max 145 MHz
[    13.395] (II) fglrx(1): EDID (in hex):
[    13.395] (II) fglrx(1):     00ffffffffffff0010ac0e704c364431
[    13.395] (II) fglrx(1):     110f010368261e782ece50a3544c9926
[    13.395] (II) fglrx(1):     0f5054a54b00714f8180010101010101
[    13.395] (II) fglrx(1):     010101010101302a009851002a403070
[    13.395] (II) fglrx(1):     1300782d1100001e000000ff00363431
[    13.395] (II) fglrx(1):     383035344a3144364c0a000000fc0044
[    13.395] (II) fglrx(1):     454c4c204531393346500a20000000fd
[    13.395] (II) fglrx(1):     00384c1f530e000a202020202020003b
[    13.395] (II) fglrx(1): Printing probed modes for output CRT1
[    13.395] (II) fglrx(1): Modeline "1280x1024"x60.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz eP)
[    13.395] (II) fglrx(1): Modeline "1280x1024"x75.0  135.00  1280 1296 1440 1688  1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[    13.395] (II) fglrx(1): Modeline "1280x960"x75.0  135.00  1280 1296 1440 1688  960 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[    13.395] (II) fglrx(1): Modeline "1280x960"x60.0  108.00  1280 1328 1440 1688  960 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[    13.395] (II) fglrx(1): Modeline "1152x864"x75.0  108.00  1152 1216 1344 1600  864 865 868 900 +hsync +vsync (67.5 kHz e)
[    13.395] (II) fglrx(1): Modeline "1152x864"x60.0  108.00  1152 1328 1440 1688  864 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[    13.395] (II) fglrx(1): Modeline "1280x768"x75.0  135.00  1280 1296 1440 1688  768 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[    13.395] (II) fglrx(1): Modeline "1280x768"x60.0  108.00  1280 1328 1440 1688  768 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[    13.395] (II) fglrx(1): Modeline "1280x720"x75.0  135.00  1280 1296 1440 1688  720 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[    13.395] (II) fglrx(1): Modeline "1280x720"x60.0  108.00  1280 1328 1440 1688  720 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[    13.395] (II) fglrx(1): Modeline "1024x768"x75.0   78.75  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.0 kHz e)
[    13.395] (II) fglrx(1): Modeline "1024x768"x60.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz e)
[    13.395] (II) fglrx(1): Modeline "800x600"x75.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync (46.9 kHz e)
[    13.395] (II) fglrx(1): Modeline "800x600"x60.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz e)
[    13.395] (II) fglrx(1): Modeline "640x480"x75.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz e)
[    13.395] (II) fglrx(1): Modeline "640x480"x60.0   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz e)
[    13.395] (II) fglrx(1): Output DFP1 disconnected
[    13.395] (II) fglrx(1): Output DFP2 disconnected
[    13.395] (II) fglrx(1): Output DFP3 disconnected
[    13.395] (II) fglrx(1): Output DFP4 disconnected
[    13.395] (II) fglrx(1): Output DFP5 disconnected
[    13.395] (II) fglrx(1): Output DFP6 disconnected
[    13.395] (II) fglrx(1): Output DFP7 disconnected
[    13.395] (II) fglrx(1): Output CRT1 connected
[    13.395] (II) fglrx(1): Using exact sizes for initial modes
[    13.395] (II) fglrx(1): Output CRT1 using initial mode 1280x1024
[    13.395] (II) fglrx(1): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[    13.395] (II) fglrx(1): DPI set to (96, 96)
[    13.395] (WW) fglrx(0): Unable to register ADL handler for 0x00110000
[    13.395] (WW) fglrx(0): Unable to register ADL handler for 0x00120000
[    13.395] (WW) fglrx(0): Unable to register ADL handler for 0x00130000
[    13.395] (WW) fglrx(0): Unable to register ADL handler for 0x00150000
[    13.395] (II) fglrx(1): Eyefinity capable adapter detected.
[    13.395] (II) fglrx(1): Adapter AMD Radeon HD 6900 Series  has 6 configurable heads and 1 displays connected.
[    13.395] (==) fglrx(1):  PseudoColor visuals disabled
[    13.395] (II) Loading sub module "ramdac"
[    13.395] (II) LoadModule: "ramdac"
[    13.395] (II) Module "ramdac" already built-in
[    13.395] (==) fglrx(1): NoDRI = NO
[    13.395] (==) fglrx(1): Capabilities: 0x00000000
[    13.395] (==) fglrx(1): CapabilitiesEx: 0x00000000
[    13.395] (==) fglrx(1): OpenGL ClientDriverName: "fglrx_dri.so"
[    13.395] (==) fglrx(1): UseFastTLS=0
[    13.395] (II) fglrx(1): Desktop Vsync is enabled.
[    13.396] (II) fglrx(0): Shadow Primary option: ShadowPrimary is enabled
[    13.396] (--) Depth 24 pixmap format is 32 bpp
[    13.396] Loading extension ATIFGLRXDRI
[    13.396] (II) fglrx(0): doing swlDriScreenInit
[    13.396] (II) fglrx(0): swlDriScreenInit for fglrx driver
[    13.396] ukiDynamicMajor: found major device number 250
[    13.396] ukiDynamicMajor: found major device number 250
[    13.396] ukiDynamicMajor: found major device number 250
[    13.396] ukiOpenByBusid: Searching for BusID PCI:1:0:0
[    13.396] ukiOpenDevice: node name is /dev/ati/card0
[    13.396] ukiOpenDevice: open result is 16, (OK)
[    13.396] ukiOpenByBusid: ukiOpenMinor returns 16
[    13.396] ukiOpenByBusid: ukiGetBusid reports PCI:2:0:0
[    13.396] ukiOpenDevice: node name is /dev/ati/card1
[    13.396] ukiOpenDevice: open result is 16, (OK)
[    13.396] ukiOpenByBusid: ukiOpenMinor returns 16
[    13.396] ukiOpenByBusid: ukiGetBusid reports PCI:1:0:0
[    13.396] (II) fglrx(0): [uki] DRM interface version 1.0
[    13.396] (II) fglrx(0): [uki] created "fglrx" driver at busid "PCI:1:0:0"
[    13.396] (II) fglrx(0): [uki] added 8192 byte SAREA at 0x2000
[    13.396] (II) fglrx(0): [uki] mapped SAREA 0x2000 to 0x7ffd260e0000
[    13.396] (II) fglrx(0): [uki] framebuffer handle = 0x3000
[    13.396] (II) fglrx(0): [uki] added 1 reserved context for kernel
[    13.396] (II) fglrx(0): swlDriScreenInit done
[    13.396] (II) fglrx(0): Kernel Module Version Information:
[    13.396] (II) fglrx(0):     Name: fglrx
[    13.396] (II) fglrx(0):     Version: 9.0.2
[    13.396] (II) fglrx(0):     Date: Sep 20 2012
[    13.396] (II) fglrx(0):     Desc: AMD FireGL DRM kernel module
[    13.396] (II) fglrx(0): Kernel Module version matches driver.
[    13.396] (II) fglrx(0): Kernel Module Build Time Information:
[    13.396] (II) fglrx(0):     Build-Kernel UTS_RELEASE:        3.5.0-17-generic
[    13.396] (II) fglrx(0):     Build-Kernel MODVERSIONS:        yes
[    13.396] (II) fglrx(0):     Build-Kernel __SMP__:            yes
[    13.396] (II) fglrx(0):     Build-Kernel PAGE_SIZE:          0x1000
[    13.396] (II) fglrx(0): [uki] register handle = 0x00004000
[    13.397] (II) fglrx(0): DRI initialization successfull
[    13.397] (II) fglrx(0): FBADPhys: 0xf400000000 FBMappedSize: 0x01040000
[    13.397] (==) fglrx(0): Backing store disabled
[    13.397] Loading extension FGLRXEXTENSION
[    13.397] (**) fglrx(0): DPMS enabled
[    13.397] (II) fglrx(0): Initialized in-driver Xinerama extension
[    13.397] (**) fglrx(0): Textured Video is enabled.
[    13.397] (II) LoadModule: "glesx"
[    13.397] (II) Loading /usr/lib/x86_64-linux-gnu/xorg/extra-modules/modules/glesx.so
[    13.398] (II) Module glesx: vendor="X.Org Foundation"
[    13.398]     compiled for 1.4.99.906, module version = 1.0.0
[    13.398] Loading extension GLESX
[    13.398] (II) fglrx(0): GLESX enableFlags = 592
[    13.398] (II) fglrx(0): GLESX is enabled
[    13.398] (II) LoadModule: "amdxmm"
[    13.398] (II) Loading /usr/lib/x86_64-linux-gnu/xorg/extra-modules/modules/amdxmm.so
[    13.398] (II) Module amdxmm: vendor="X.Org Foundation"
[    13.398]     compiled for 1.4.99.906, module version = 2.0.0
[    13.406] Loading extension AMDXVOPL
[    13.406] Loading extension AMDXVBA
[    13.406] (II) fglrx(0): Composite extension is not loaded
[    13.406] (WW) fglrx(0): Option "VendorName" is not used
[    13.406] (WW) fglrx(0): Option "ModelName" is not used
[    13.406] (II) fglrx(0): X context handle = 0x1
[    13.406] (II) fglrx(0): [DRI] installation complete
[    13.406] (==) fglrx(0): Silken mouse enabled
[    13.406] (==) fglrx(0): Using HW cursor of display infrastructure!
[    13.406] (II) fglrx(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[    13.527] (II) fglrx(0): Framebuffer compression enabled: mcAddr=0xf40b960000 width=0xa00 height=0x1934
[    13.527] (--) RandR disabled
[    13.527] (II) fglrx(1): doing swlDriScreenInit
[    13.527] (II) fglrx(1): swlDriScreenInit for fglrx driver
[    13.527] ukiDynamicMajor: found major device number 250
[    13.527] ukiDynamicMajor: found major device number 250
[    13.527] ukiDynamicMajor: found major device number 250
[    13.527] ukiOpenByBusid: Searching for BusID PCI:2:0:0
[    13.527] ukiOpenDevice: node name is /dev/ati/card0
[    13.527] ukiOpenDevice: open result is 17, (OK)
[    13.527] ukiOpenByBusid: ukiOpenMinor returns 17
[    13.527] ukiOpenByBusid: ukiGetBusid reports PCI:2:0:0
[    13.527] (II) fglrx(1): [uki] DRM interface version 1.0
[    13.527] (II) fglrx(1): [uki] created "fglrx" driver at busid "PCI:2:0:0"
[    13.527] (II) fglrx(1): [uki] added 8192 byte SAREA at 0x19000
[    13.527] (II) fglrx(1): [uki] mapped SAREA 0x19000 to 0x7ffd201c0000
[    13.527] (II) fglrx(1): [uki] framebuffer handle = 0x1a000
[    13.527] (II) fglrx(1): [uki] added 1 reserved context for kernel
[    13.527] (II) fglrx(1): swlDriScreenInit done
[    13.527] (II) fglrx(1): Kernel Module Version Information:
[    13.528] (II) fglrx(1):     Name: fglrx
[    13.528] (II) fglrx(1):     Version: 9.0.2
[    13.528] (II) fglrx(1):     Date: Sep 20 2012
[    13.528] (II) fglrx(1):     Desc: AMD FireGL DRM kernel module
[    13.528] (II) fglrx(1): Kernel Module version matches driver.
[    13.528] (II) fglrx(1): Kernel Module Build Time Information:
[    13.528] (II) fglrx(1):     Build-Kernel UTS_RELEASE:        3.5.0-17-generic
[    13.528] (II) fglrx(1):     Build-Kernel MODVERSIONS:        yes
[    13.528] (II) fglrx(1):     Build-Kernel __SMP__:            yes
[    13.528] (II) fglrx(1):     Build-Kernel PAGE_SIZE:          0x1000

503guy

Full Member

Offline

Activity: 140
Merit: 100

Re: Looking for Help with Multiple Graphics Card Setup in Xubuntu 12.10 for Bitcoin

April 22, 2013, 08:07:53 PM

#2

You never mentioned what your problem is?

Virtual Miners - cex.io - check it out

tysat

Legendary

Offline

Activity: 966
Merit: 1004

Keep it real

Re: Looking for Help with Multiple Graphics Card Setup in Xubuntu 12.10 for Bitcoin

April 22, 2013, 08:13:32 PM

#3

Did a little editing on your OP (throwing in code tags to make it easier to read). I think the logs were too long, because text was being truncated near the end.

Also going to whitelist OP and move this topic, it's less likely to be answered in the newbie section... plus I'm running Ubuntu 12.10 too and am curious.

theonlineanswer (OP)

Newbie

Offline

Activity: 5
Merit: 0

Re: Looking for Help with Multiple Graphics Card Setup in Xubuntu 12.10 for Bitcoin

April 22, 2013, 09:40:32 PM

#4

Quote from: 503guy on April 22, 2013, 08:07:53 PM

You never mentioned what your problem is?

I want to run 2 graphics cards for mining - I can only get 1 card to work at a time. Even if I stand on my head - I am having no luck. I tried to cover all my bases and answer may of the questions that I have seen people ask already on the forums.

theonlineanswer (OP)

Newbie

Offline

Activity: 5
Merit: 0

Re: Looking for Help with Multiple Graphics Card Setup in Xubuntu 12.10 for Bitcoin

April 22, 2013, 09:42:43 PM

#5

Quote from: tysat on April 22, 2013, 08:13:32 PM

Did a little editing on your OP (throwing in code tags to make it easier to read). I think the logs were too long, because text was being truncated near the end.

Also going to whitelist OP and move this topic, it's less likely to be answered in the newbie section... plus I'm running Ubuntu 12.10 too and am curious.

I appreciate the help. I figured it would be too much information for one post which is why I created the pdf for everything. Also, I didn't want to waste anyone's time by not trying everything I could find to attempt to resolve the problem.

Do you have the same / similar issue? What graphics cards are you running on your 12.10 Xubuntu?

tysat

Legendary

Offline

Activity: 966
Merit: 1004

Keep it real

Re: Looking for Help with Multiple Graphics Card Setup in Xubuntu 12.10 for Bitcoin

April 22, 2013, 11:35:01 PM

#6

Quote from: theonlineanswer on April 22, 2013, 09:42:43 PM

Do you have the same / similar issue? What graphics cards are you running on your 12.10 Xubuntu?

I only have one card, a 7870 I think, but am not really trying to mine right now. I'm in a similar situation to you, just switched over to Ubuntu 12.10 after a bad sector on my HD killed the windows install. Tried a little to get it working, but the card never got detected by cgminer.

theonlineanswer (OP)

Newbie

Offline

Activity: 5
Merit: 0

Re: Looking for Help with Multiple Graphics Card Setup in Xubuntu 12.10 for Bitcoin

April 23, 2013, 03:00:58 AM

#7

For one card - follow this guide's instructions (if you can afford if the pc breaks...)

https://docs.google.com/document/d/1Gw7YPYgMgNNU42skibULbJJUx_suP_CpjSEdSi8_z9U/preview?sle=true

For 7xxx series you could try this...

sudo apt-get install fglrx-updates fglrx-amdcccle-updates fglrx-updates-dev
aticonfig --lsa (If correct, will show your video card)
sudo aticonfig --adapter=all --initial (writes to xorg.conf file)
sudo reboot
sudo aticonfig --adapter=all --odgt (Tests configuration - see examples in that guide)

Here's the cgminer stuff to check for it:
cd cgminer-2.9.5-x86_64-built
export DISPLAY=:0
export GPU_USE_SYNC_OBJECTS=1
./cgminer -n

The drivers worked for 1 card - just not 2. Getting ready to post what I think the issue is but want to grab a bit more data to post.

theonlineanswer (OP)

Newbie

Offline

Activity: 5
Merit: 0

Re: Looking for Help with Multiple Graphics Card Setup in Xubuntu 12.10 for Bitcoin

April 23, 2013, 03:34:05 AM

#8

Update: I think I sorted out most of the issues and narrowed down my issue to a --gpu mapping issue. I have NO idea how to gpu map - if someone can point me to enough information so that I know what to configure for a

Raedeon 7950 tahiti - this is using opencl (according to cgminer)
Raedeon 6950 cayman - this is adl not opencl (according to cgminer)

That would be great.

Here's my procedure:

1. Installed clean install Xubuntu (Ubuntu 12.10)
2. Installed software updates for ubuntu (189 updates)
3. Rebooted
4. Follow Bitcoin system guide - using 7xxx instructions to install driver, create and verify ati / xorb.conf
5. Installed Icetea Java (for bitminter)
6. Setup Catalyst with Ximera tearaway for dual monitor display
7. Rebooted
8. Downloaded / ran cgminer according to bitcoin guide

Received the following error:

~/Desktop$ aticonfig --lsa
* 0. 01:00.0 AMD Radeon HD 7900 Series
1. 02:00.0 AMD Radeon HD 6900 Series
* - Default adapter

:~/Documents/cgminer-3.0.0-x86_64-built$ export DISPLAY=:0
:~/Documents/cgminer-3.0.0-x86_64-built$ export GPU_USE_SYNC_OBJECTS=1
:~/Documents/cgminer-3.0.0-x86_64-built$ ./cgminer -n

[2013-04-22 21:23:26] CL Platform 0 vendor: Advanced Micro Devices, Inc.
[2013-04-22 21:23:26] CL Platform 0 name: AMD Accelerated Parallel Processing
[2013-04-22 21:23:26] CL Platform 0 version: OpenCL 1.2 AMD-APP (1016.4)
[2013-04-22 21:23:26] Platform 0 devices: 1
[2013-04-22 21:23:26] 0 Tahiti

[2013-04-22 21:23:26] ADL found more devices than opencl!
[2013-04-22 21:23:26] There is possibly at least one GPU that doesn't support OpenCL
[2013-04-22 21:23:26] Use the gpu map feature to reliably map OpenCL to ADL
[2013-04-22 21:23:26] WARNING: Number of OpenCL and ADL devices did not match!
[2013-04-22 21:23:26] Hardware monitoring may NOT match up with devices!

[2013-04-22 21:23:26] GPU 0 AMD Radeon HD 7900 Series hardware monitoring enabled
[2013-04-22 21:23:26] 1 GPU devices max detected
[2013-04-22 21:23:26] USB all: found 12 devices - listing known devices
[2013-04-22 21:23:26] No known USB devices

When I searched for this error message, I found this on cgminer's website:

3. There are more ADL devices than OpenCL. ADL devices include any ATI GPUs,
including ones that can't mine, like some older R4xxx cards.

To cope with this, the ADVANCED option for --gpu-map is provided with cgminer.
DO NOT USE THIS UNLESS YOU KNOW WHAT YOU ARE DOING. The default will work the
vast majority of the time unless you know you have a problem already.

To get useful information, start cgminer with just the -n option. You will get
output that looks like this:

[2012-04-25 13:17:34] CL Platform 0 vendor: Advanced Micro Devices, Inc.
[2012-04-25 13:17:34] CL Platform 0 name: AMD Accelerated Parallel Processing
[2012-04-25 13:17:34] CL Platform 0 version: OpenCL 1.1 AMD-APP (844.4)
[2012-04-25 13:17:34] Platform 0 devices: 3
[2012-04-25 13:17:34] 0 Tahiti
[2012-04-25 13:17:34] 1 Tahiti
[2012-04-25 13:17:34] 2 Cayman
[2012-04-25 13:17:34] GPU 0 AMD Radeon HD 7900 Series hardware monitoring enabled
[2012-04-25 13:17:34] GPU 1 AMD Radeon HD 7900 Series hardware monitoring enabled
[2012-04-25 13:17:34] GPU 2 AMD Radeon HD 6900 Series hardware monitoring enabled
[2012-04-25 13:17:34] 3 GPU devices max detected

Note the number of devices here match, and the order is the same. If devices 1
and 2 were different between Tahiti and Cayman, you could run cgminer with:
--gpu-map 2:1,1:2
And it would swap the monitoring it received from ADL device 1 and put it to
opencl device 2 and vice versa.

If you have 2 monitors connected to the first device it would look like this:

[2012-04-25 13:17:34] Platform 0 devices: 4
[2012-04-25 13:17:34] 0 Tahiti
[2012-04-25 13:17:34] 1 Tahiti
[2012-04-25 13:17:34] 2 Tahiti
[2012-04-25 13:17:34] 3 Cayman
[2012-04-25 13:17:34] GPU 0 AMD Radeon HD 7900 Series hardware monitoring enabled
[2012-04-25 13:17:34] GPU 1 AMD Radeon HD 7900 Series hardware monitoring enabled
[2012-04-25 13:17:34] GPU 2 AMD Radeon HD 6900 Series hardware monitoring enabled

To work around this, you would use:
-d 0 -d 2 -d 3 --gpu-map 2:1,3:2

If you have an older card as well as the rest it would look like this:

[2012-04-25 13:17:34] Platform 0 devices: 3
[2012-04-25 13:17:34] 0 Tahiti
[2012-04-25 13:17:34] 1 Tahiti
[2012-04-25 13:17:34] 2 Cayman
[2012-04-25 13:17:34] GPU 0 AMD Radeon HD 4500 Series hardware monitoring enabled
[2012-04-25 13:17:34] GPU 1 AMD Radeon HD 7900 Series hardware monitoring enabled
[2012-04-25 13:17:34] GPU 2 AMD Radeon HD 7900 Series hardware monitoring enabled
[2012-04-25 13:17:34] GPU 3 AMD Radeon HD 6900 Series hardware monitoring enabled

To work around this you would use:
--gpu-map 0:1,1:2,2:3

Is this enough information for someone to help me figure out gpu mapping - or do you need the xorg.conf (updated version)?

503guy

Full Member

Offline

Activity: 140
Merit: 100

Re: Looking for Help with Multiple Graphics Card Setup in Xubuntu 12.10 for Bitcoin

April 24, 2013, 07:43:40 AM

#9

Does the below command give you a temp readout of both cards? If so, then you have installed your cards correctly -- but for some reason cgminer is not picking them up. I see you are using export DISPLAY=:0 -- make sure you use that before opening cgminer EVERYTIME.

Code:

sudo aticonfig --adapter=all --odgt

Ensure you properly installed both AMD-APP-SDK-v2.8-RC-lnx64.tgz and ADL_SDK_5.0.zip -- you need both before cgminer will work properly

Virtual Miners - cex.io - check it out