[WTS] HDMI dummy plug, 4K, EDID emulator monitor, USB WatchDog Timer

[igorwhite]

Emulator Monitor

Emulates a monitor connected to the graphics card.
Remote control programs such as TeamVewer, Radmin, VNC and others without a monitor present operating only in screen resolution 640x480.
This emulator is designed to simulate the presence of a monitor output video card. It allows you to simulate the screen resolution with a maximum resolution of 4k (3840x2160).
Attention!!!
Resolution 4k (3840x2160) available only with HDMI 1.4, only newest GPUs
Default resolution Full HD (1920x1080)

Also it allows you to run a system that will not start without a monitor!!!

* Plug and Play.

* System Windows/Linux/Mac

* Compatible with any graphics card that has an HDMI output.

* Emulates 8 channel audio up to 192 kHz.

Screen:

Prices for: Ebay

The cost of 1 piece is 7.99 $
The cost of 5 piece is 34.95 $ (LOT 5 PCS)

Special prices for BitcoinTalk - Without Ebay:

1 piece is – 6.99 $ + Post of Russia with tracking 3.5 $
10 piece is – 60 $ + Post of Russia with tracking 6 $
50 piece is – 266 $ + Post of Russia with tracking 11 $

USB WatchDog Timer

WatchDog Prime

USB WatchDog Timer (the Device) is designed to restart and shutdown/turn on the PC in case of hanging or overheating of its individual nodes (CPU and/or GPU). The device is a compact solution that monitors the status of a PC via USB interface. In the case of an unresponsive computer program (Device GPU) will cease to send a signal that will trigger the alarm system reboot or shutdown (or both of them, depending on the setting. Also, the timer will give a reset signal in the case of GPU failure, CPU overheating and/or graphics cards or their small load. In addition, the device provides a system for updating the firmware to fix errors and expand the functionality.

• WatchDog Prime is defined in the system as a full-fledged HID device without virtualization of the COM port
• WatchDog Prime software has an intuitive interface
• Built-in "Power" and "Reset" buttons
• Duplicating contacts "Power" and "Reset" for connecting external buttons
• WatchDog Prime version "USB-PBD10" has reverse polarity protection
• The version of the LITE software is only from the hang of the system (control of Reset and Power)
• Variants of execution: USB-A or USB PBD-10

Characteristics:

• Control Reset and Power ON/OFF - Restart or Shutdown when the system hangs.
• CPU and GPU temperature control - Reboot or Shutdown when the permissible values ​​are exceeded.
• Control of all installed GPUs - Reboot or Disconnect if the GPU fails. (crash video card - remote access is not possible, and the system does not hang)
• Resetting the PC in case of low average GPU load (hang of the program of the miner)
• Connection Test Option (PING) - If the resource is available, but calculations do not go - a problem in the PC, and a reboot is required
• Automatically turn on the PC when power is on
• Control CPU and GPU fans
• Permanent reboot of the computer in case of not loading into the system and detection of software

Downloads:
Software: v.1.53.1 Firmware: v.1.52


Special prices for BitcoinTalk:

1 piece is – 26 $ + Post of Russia with tracking 3.5 $
10 piece is – 120 $ + Post of Russia with tracking 10 $
50 piece is – 1000 $ + Post of Russia with tracking 22 $



Location: Russian Federation

Sending Worldwide:
Post of Russia with tracking - 3.5 $
Fast shipping EMS of Russia with tracking - 40 $

Order and Payment only via e-mail: esonics.store@gmail.com
Payment:
Paypal
Bitcoin BTC
Ethereum [ETH]

My shop: Ebay

[Eyedol-X]

Very nice -- Will you have any models in the future that actually have some sort of plastic enclosure or will the all be heat shrink only?

[igorwhite]

Yes, now the case is under construction

[igorwhite]

Emulators in Stock!!!

[klaaas]

These could be handy'
If i need to order i will pm.

[Jamievs]

Nice, just ordered a couple on ebay 

[igorwhite]

Jamievs
Yes, I saw the payment

[cavaliersrus]

would be cool to play with one of these to make a case for it with my 3d printer but sadly no funds at this time

[igorwhite]

Nice, just ordered a couple on ebay 

Jamievs, I sent the parcel

[igorwhite]

Hello!

[isoneguy]

just ordered 5

I'll update trust when they arrive!

thanks 

[igorwhite]

Yesterday's orders are all sent

[cavaliersrus]

hey igor would you be willing to send me one so i can see about making a 3d printed case for your plug ?

[Lion BItcoin Shop]

any special price ? or discount ? for paying use bitcoin?
interesting to buy 1 lot (5pcs) , anyway how about DHL express shipping? im not see dhl option at your store

[CjMapope]

Hey Hey, i would be interested in 5 pieces of these little buggers
shipped to Canada.
Let me know how to proceed or just send me a PM and well seal this deal, these are great little pieces and stupidly hard to have handy when you need them haha

[igorwhite]

any special price ? or discount ? for paying use bitcoin?
interesting to buy 1 lot (5pcs) , anyway how about DHL express shipping? im not see dhl option at your store

I will make special prices for BitcoinTalk - Without Ebay
I will make payment in bitcoin and add a fast delivery - EMS

[igorwhite]

Hey Hey, i would be interested in 5 pieces of these little buggers
shipped to Canada.
Let me know how to proceed or just send me a PM and well seal this deal, these are great little pieces and stupidly hard to have handy when you need them haha

I already sent a lot of parcels to Canada.
Write to me by e-mail or PM.
I will issue an invoice.

[cavaliersrus]

take that as a no igor on me making a 3d printed case for this

[igorwhite]

Prototype HDMI Emulator in case

[isoneguy]

the case just needs to be something you can grab onto

it also shouldn't cover the plug...