EthOS / Claymore 9.0 Dual Mining ETH and SIA

[jonnyen]

Hello,

First post to forum. 

I am running a test machine with one Sapphire RX 470 on the latest version of ethOS.   I also have a Windows 10 machine which I have been able to configure correctly to dual mine ETH and SIA.   I can't figure out what to change in ethOS to make it dual mine ETH and SIA or if it even possible?

Can anyone tell me how I need to edit local.config or claymore.sh or what else I might need to do?

thanks
JY

[boatznhoes]

Claymore settings can be changed in claymore.stub.conf, but not sure if you can make this work

[moonelf]

Did you ever get this working? I am new to ethOS and would like to dual mine ETH and DCR but unclear how to edit claymore.stub for DCR. I've got ETH working properly.

[moxyf]

There's a few lines you just need to uncomment in claymore.stub.conf to start dual mining. They're outlined in the file

[toptek]

in the claymore.stub.conf are these lines below:

uncomment and configure the -dpool and -dwal lines below to enable dualmining.

Then  go to the local.conf in the home Directly and put in your pool and wallet for the ETH miner, if your using the local.conf, I think i haven't really look into setting up dual mining yet with Ethos.

I have only learned to use the local.conf and claymore.stub conf's for eth and Zec mining .. haven't tried the remote or custom conf's .no need to,yet.!!!

I have EthOS running on two rigs .

claymore.stub.conf

# WARNING! Remove "#" characters to enable lines, with "#" they are disabled and will be ignored by miner! Check README for details.
# WARNING! Miner loads options from this file only if there are not any options in the command line!
-colors 1
-dbg -1
-esm STRATUMTYPE
-epool POOL1
-ewal WALLET
-epsw PASSWORD1
-eworker WORKER
-allpools 1
-gser 2
-allcoins 1
-wd 0

#uncomment and configure the -dpool and -dwal lines below to enable dualmining.
-mode 0

#-ewal 0xD69af2A796A737A103F12d2f0BCC563a13900E6F
#-epsw x
#-dpool stratum+tcp://yiimp.ccminer.org:4252
#-dwal DsUt9QagrYLvSkJHXCvhfiZHKafVtzd7Sq4
#-dpsw x
#-esm 1
#-mode 0
#-tt 70



then go to the local.conf in the same directly as the claymore.stub.conf and put in your pool and wallet for eth mining,you can leave the flags how they are for default setting, it didn't seem to matter if they are there or not .. if your using the local.conf, which is all i have learned to use.

some thing like below

local.conf

globalminer claymore
maxgputemp 85
stratumproxy enabled
proxywallet your wallet for eth
proxypool1 the pool you are using for eth mining.
globalfan 85
flags -logfile noappend.txt  
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
I put the -logfile noappend.txt line in,because i don't like a lot of log files every time, i reboot or restart the miner it would make one, other wise that line is not needed, and all it does is over write the old log and replace it with a new log from the session running instead of making a new one for each restart ..

[Jackhalo3]

in the claymore.stub.conf are these lines below:

uncomment and configure the -dpool and -dwal lines below to enable dualmining.

Then  go to the local.conf in the home Directly and put in your pool and wallet for the ETH miner, if your using the local.conf, I think i haven't really look into setting up dual mining yet with Ethos.

I have only learned to use the local.conf and claymore.stub conf's for eth and Zec mining .. haven't tried the remote or custom conf's .no need to,yet.!!!

I have EthOS running on two rigs .

claymore.stub.conf

# WARNING! Remove "#" characters to enable lines, with "#" they are disabled and will be ignored by miner! Check README for details.
# WARNING! Miner loads options from this file only if there are not any options in the command line!
-colors 1
-dbg -1
-esm STRATUMTYPE
-epool POOL1
-ewal WALLET
-epsw PASSWORD1
-eworker WORKER
-allpools 1
-gser 2
-allcoins 1
-wd 0

#uncomment and configure the -dpool and -dwal lines below to enable dualmining.
-mode 0

#-ewal 0xD69af2A796A737A103F12d2f0BCC563a13900E6F
#-epsw x
#-dpool stratum+tcp://yiimp.ccminer.org:4252
#-dwal DsUt9QagrYLvSkJHXCvhfiZHKafVtzd7Sq4
#-dpsw x
#-esm 1
#-mode 0
#-tt 70



then go to the local.conf in the same directly as the claymore.stub.conf and put in your pool and wallet for eth mining,you can leave the flags how they are for default setting, it didn't seem to matter if they are there or not .. if your using the local.conf, which is all i have learned to use.

some thing like below

local.conf

globalminer claymore
maxgputemp 85
stratumproxy enabled
proxywallet your wallet for eth
proxypool1 the pool you are using for eth mining.
globalfan 85
flags -logfile noappend.txt  
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
I put the -logfile noappend.txt line in,because i don't like a lot of log files every time, i reboot or restart the miner it would make one, other wise that line is not needed, and all it does is over write the old log and replace it with a new log from the session running instead of making a new one for each restart ..

Just got it working! What you said to do worked, however you also have to specify what coin you are mining. To do this, simply add -dcoin somewhere in claymore.stub.conf followed by the coin you want to mine, sc for SIA.

[moonelf]

Thanks much for the clear explanation. Works well to dual mine ETH & DCR. Was pretty easy once I realized I knew nothing about ethOS and must learn something new. So my answer was to learn how to even open the claymore.stub using 'nano'. In terminal type

nano claymore.stub.conf

Maybe another total newbie to ethOS like me finds this useful

Been mining fairly stable but every several hours one or more GPU hashrates drop to 0. Still working out the bugs in my system. I have tried different global core, memory, and powertune settings in local.conf file. It seems to run better now but not perfect.

[lonegunman77]

Thank you Moonelf!

Another ethOS noob here - small Linux background helps but it's the people like you that make this community awesome

Thanks for sharing, can't wait to set this up!!!

[nedrah]

I am having trouble trying to get Ethos to dual mine.
This is my claymore.stub  and below is my local.conf after

# WARNING! Remove "#" characters to enable lines, with "#" they are disabled and will be ignored by miner! Check README for details.
# WARNING! Miner loads options from this file only if there are not any options in the command line!
-colors 0
-dbg -1
-esm STRATUMTYPE
-epool pool-usa.ethosdistro.com:5001
-ewal 0xde881e95b6bede8af1c64c3d1b00851394d86517
-epsw x
-eworker miner1
-allpools 1
-gser 2
-allcoins 1
-wd 0

#uncomment and configure the -dpool and -dwal lines below to enable dualmining.
-mode 0

-ewal 0xde881e95b6bede8af1c64c3d1b00851394d86517
-epsw x
-dpool stratum+tcp://dcr.suprnova.cc:3252
-dwal DseMaxHQsJF5ZsDJyRhswJ5j35uUU2nuHnD
-dpsw testpassword
-esm 1
-mode 0
-tt 70
-dcoin

Local.conf

globaldriver amdgpu

globalfan 99

globalminer claymore

globalpowertune 4

maxgputemp 85

stratumproxy enabled

proxywallet 0xde881e95b6bede8af1c64c3d1b00851394d86517

proxypool1 pool-usa.ethosdistro.com:5001

proxypool2 pool-eu.ethosdistro.com:5001

flags --cl-global-work 8192
 --farm-recheck 200


Second day with Ethos. Loving it so far. What do I need to change to dual mine dcr?

[jaimefcb]

Second day with Ethos. Loving it so far. What do I need to change to dual mine dcr?

Here you have my config in case it helps:

Local.conf

Code:

globalminer claymore
maxgputemp 85
stratumproxy enabled
proxywallet 0xMyEtherWalletInHere
proxypool1 pool-eu.ethosdistro.com:5001
proxypool2 pool-usa.ethosdistro.com:5001
flags --cl-global-work 8192 --farm-recheck 200
globalcore 1200
globalmem 2350
globalpowertune 3
globalfan 40

Claymore.stub.conf

Code:

# WARNING! Miner loads options from this file only if there are not any options in the command line!
-colors 0
-dbg -1
-esm STRATUMTYPE
-epool POOL1
-ewal WALLET
-epsw PASSWORD1
-eworker WORKER
-allpools 1
-gser 2
-allcoins 1
-wd 0
-ethi 16

#Dual-Mining Params
-mode 0
-dcoin sia
-dpool stratum+tcp://sia-eu1.nanopool.org:7777
-dwal MySiaWalletInHere
-dcri 20

These are my stats:

Code:

GPU #0: Ellesmere, 8145 MB available, 36 compute units
ETH - Total Speed: 28.799 Mh/s, Total Shares: 15, Rejected: 0, Time: 00:55
ETH: GPU0 28.799 Mh/s
 SC - Total Speed: 575.982 Mh/s, Total Shares: 14, Rejected: 0
 SC: GPU0 575.982 Mh/s
Incorrect ETH shares: none
Pool switches: ETH - 0, SC - 0
Current ETH share target: 0x00000000dbe6fece (diff: 5000MH), epoch #127
Current SC share target: 0x0000000007547ff5 (diff: 150GH)
GPU0 t=62C fan=40%

Wattmeter says 198W on Mining time!
The system is consuming 50W with GPU and before starting mining, and 20W without GPU.

The GPU is a "MSI RX 580 GAMING X PLUS 8GB (SAMSUNG)" and my MoBo is a "MSI Z170A KRAIT GAMING 3X".

I have been testing under/overclocking mem and gpu and the best config I found is that one I have now.
My next step is try under/overvoltaging mem and gpu and do some bios tuning in order to go beyond 28.8MHs on Dual Mining and try to reduce my Power Consumption...

Anyway, I am a little bit surprised about that 2350 MHz my memories can reach, I have been reading and didn´t found any other value like that one. Anyone have an idea why?
By the way, latest ethOS and Claymore versions in here.

BR!

[nedrah]

I changed my settings and it is dual mining but all my dcr shares are getting rejected.

[nedrah]

I got it . Dwal didn't want my address. Suprnova uses username.  Thanks for everything team !!

[Cryptonite_io]

Thanks for the great post. I used it to get up and running with ease!!!

Question... I've been mining for 2 hours on SC and it shows I still have a 0 balance. Reading other forums, it says it's because i dont have my miner named. How were you able to bypass that?

Nanopool is showing my hashrate, and showing shares, but still at 0 for SIA. Thanks for the help.

[Cryptonite_io]

Thanks for the great post. I used it to get up and running with ease!!!

Question... I've been mining for 2 hours on SC and it shows I still have a 0 balance. Reading other forums, it says it's because i dont have my miner named. How were you able to bypass that?

Nanopool is showing my hashrate, and showing shares, but still at 0 for SIA. Thanks for the help.

So I solved my own problem... thought I would post it here in case some other noob like myself runs into the same problem. When you put in your wallet address at -dwal you put a period (.) after it, and your miner name (can be anything).

[nedrah]

I have been mining for a week with half my rigs on ethos. They are not giving me any credit in dwarfpool when I switched all the windows rigs over to Zec and I show no hash at dwarfpool on my ethos claymore dual rigs that I did not switch yet. I am getting dcr in my account but no eth.

Here is my local file
EthDcrMiner64.exe -esm 0 -mode 0 -ethi 4 -etha -1 -epool eth-us.dwarfpool.com:8008/miner1 -ewal 0xde881e95b6bede8af1c64c3d1b00851294d86517 -eworker miner1 -epsw x -dpool stratum+tcp://dcr.suprnova.cc:2252 -dwal nedrd3d288.iner2 -dpsw test
--opencl-device 1 --cl-local-work 256 --cl-global-work 16384


Here is my claymore stub

globaldriver amdgpu
globalminer claymore
maxgputemp 79
stratumproxy enabled
proxywallet 0xde881e95b6bede8aflc64c3d1b00851294d86517
proxypool1 eth-us.dwarfpool.com:8008
proxypool2 eth-us.dwarfpool.com:8008
flags --cl-global-work 8192 --farm-recheck 200
globalpowertune 4
globalfan 99



Any advice ?

[Tilos]

Here is my Config for Dual Mining with 570RX @ 1130 CoreClock, 2050 MemClock and 1500 Straps up to 2000

Ethereum 29MH/s each Card
Siacoin    460 MH/s each Card

Config:
-mode 0 -epool stratum+tcp://eu2.ethermine.org:4444 -ewal 0x9b70fcff8d8291dc028f2dc6ea6612e10fa6721a -eworker WhiteIce -epsw x -mport 0 -allcoins 1 -allpools 1 -dpool stratum+tcp://us-west.siamining.com:7777 -dwal 11d44524e1203f6f6accae2ab7e1a7b3720fa3b6ad840eee13ccfe479ecd23800dd7e256c323.Yo urWorkerName -dcoin sia -dcri 16  



SC: GPU0 454.240 Mh/s, GPU1 464.045 Mh/s
ETH: 06/11/17-08:56:37 - New job from eu2.ethermine.org:4444
ETH - Total Speed: 57.336 Mh/s, Total Shares: 30, Rejected: 0, Time: 00:39
ETH: GPU0 29.362 Mh/s, GPU1 29.274 Mh/s
SC - Total Speed: 917.376 Mh/s, Total Shares: 470, Rejected: 0
SC: GPU0 453.798 Mh/s, GPU1 463.578 Mh/s
GPU0 t=65C fan=88%, GPU1 t=65C fan=49%
SC: 06/11/17-08:56:46 - SHARE FOUND - (GPU 0)
SC: Share accepted (152 ms)!
ETH: 06/11/17-08:56:46 - New job from eu2.ethermine.org:4444
ETH - Total Speed: 57.413 Mh/s, Total Shares: 30, Rejected: 0, Time: 00:39
ETH: GPU0 29.399 Mh/s, GPU1 29.014 Mh/s
SC - Total Speed: 918.604 Mh/s, Total Shares: 471, Rejected: 0
SC: GPU0 454.382 Mh/s, GPU1 464.222 Mh/s
SC: 06/11/17-08:56:48 - SHARE FOUND - (GPU 1)
SC: Share accepted (153 ms)!
ETH: 06/11/17-08:56:54 - New job from eu2.ethermine.org:4444
ETH - Total Speed: 57.406 Mh/s, Total Shares: 30, Rejected: 0, Time: 00:39
ETH: GPU0 29.420 Mh/s, GPU1 28.985 Mh/s
SC - Total Speed: 918.487 Mh/s, Total Shares: 472, Rejected: 0
SC: GPU0 454.721 Mh/s, GPU1 463.766 Mh/s
SC: 06/11/17-08:57:00 - SHARE FOUND - (GPU 1)
SC: Share accepted (152 ms)!
SC: 06/11/17-08:57:00 - SHARE FOUND - (GPU 0)
SC: Share accepted (152 ms)!
ETH: 06/11/17-08:57:00 - New job from eu2.ethermine.org:4444
ETH - Total Speed: 57.374 Mh/s, Total Shares: 30, Rejected: 0, Time: 00:39
ETH: GPU0 29.384 Mh/s, GPU1 29.190 Mh/s
SC - Total Speed: 917.981 Mh/s, Total Shares: 474, Rejected: 0
SC: GPU0 454.141 Mh/s, GPU1 463.840 Mh/s

[fuliaro]

Here is my Config for Dual Mining with 570RX @ 1130 CoreClock, 2050 MemClock and 1500 Straps up to 2000

Ethereum 29MH/s each Card
Siacoin    460 MH/s each Card

Config:
-mode 0 -epool stratum+tcp://eu2.ethermine.org:4444 -ewal 0x9b70fcff8d8291dc028f2dc6ea6612e10fa6721a -eworker WhiteIce -epsw x -mport 0 -allcoins 1 -allpools 1 -dpool stratum+tcp://us-west.siamining.com:7777 -dwal 11d44524e1203f6f6accae2ab7e1a7b3720fa3b6ad840eee13ccfe479ecd23800dd7e256c323.Yo urWorkerName -dcoin sia -dcri 16  



SC: GPU0 454.240 Mh/s, GPU1 464.045 Mh/s
ETH: 06/11/17-08:56:37 - New job from eu2.ethermine.org:4444
ETH - Total Speed: 57.336 Mh/s, Total Shares: 30, Rejected: 0, Time: 00:39
ETH: GPU0 29.362 Mh/s, GPU1 29.274 Mh/s
SC - Total Speed: 917.376 Mh/s, Total Shares: 470, Rejected: 0
SC: GPU0 453.798 Mh/s, GPU1 463.578 Mh/s
GPU0 t=65C fan=88%, GPU1 t=65C fan=49%
SC: 06/11/17-08:56:46 - SHARE FOUND - (GPU 0)
SC: Share accepted (152 ms)!
ETH: 06/11/17-08:56:46 - New job from eu2.ethermine.org:4444
ETH - Total Speed: 57.413 Mh/s, Total Shares: 30, Rejected: 0, Time: 00:39
ETH: GPU0 29.399 Mh/s, GPU1 29.014 Mh/s
SC - Total Speed: 918.604 Mh/s, Total Shares: 471, Rejected: 0
SC: GPU0 454.382 Mh/s, GPU1 464.222 Mh/s
SC: 06/11/17-08:56:48 - SHARE FOUND - (GPU 1)
SC: Share accepted (153 ms)!
ETH: 06/11/17-08:56:54 - New job from eu2.ethermine.org:4444
ETH - Total Speed: 57.406 Mh/s, Total Shares: 30, Rejected: 0, Time: 00:39
ETH: GPU0 29.420 Mh/s, GPU1 28.985 Mh/s
SC - Total Speed: 918.487 Mh/s, Total Shares: 472, Rejected: 0
SC: GPU0 454.721 Mh/s, GPU1 463.766 Mh/s
SC: 06/11/17-08:57:00 - SHARE FOUND - (GPU 1)
SC: Share accepted (152 ms)!
SC: 06/11/17-08:57:00 - SHARE FOUND - (GPU 0)
SC: Share accepted (152 ms)!
ETH: 06/11/17-08:57:00 - New job from eu2.ethermine.org:4444
ETH - Total Speed: 57.374 Mh/s, Total Shares: 30, Rejected: 0, Time: 00:39
ETH: GPU0 29.384 Mh/s, GPU1 29.190 Mh/s
SC - Total Speed: 917.981 Mh/s, Total Shares: 474, Rejected: 0
SC: GPU0 454.141 Mh/s, GPU1 463.840 Mh/s

That's awesome, bro.
Are you getting better perf. on EthOS than Win?

[nedrah]

I have been out of town for a week.  It is only dual mines to dcr . My eth shows no hash to the correct wallet.

Can someone look at my config.

http://paste.ethosdistro.com/banufupico



Irc for ethos says they do not support dual mining.

[gcxc]

I have been out of town for a week.  It is only dual mines to dcr . My eth shows no hash to the correct wallet.

Can someone look at my config.

http://paste.ethosdistro.com/banufupico



Irc for ethos says they do not support dual mining.

I think for the -ewal address
-ewal 0xde881e95b6bede8aflc64c3d1b00851294d86517

you should change it to
-ewal 0xde881e95b6bede8aflc64c3d1b00851294d86517.somename

[nedrah]

I found out that your claymore.stub should not have your eth wallet address. It should only say wallet1. The wallet address only goes under the local.conf when mining two coins with ethos.

I hope this help someone.