Hannu (OP)
|
|
June 04, 2017, 10:45:52 PM |
|
Hey, I cannot access my AntMiner S5, im doing it hard reset. I try default ip but it not helps What i can do for it?
|
BTC: 3Qnnx4cu45Gx4WcksNCnBPu3TaUZ5sKkLo LTC: LYX1ZH7f4qcXq52AzA6grUYDfDngVz7BEi XRP: rLrbZMJDdL8eQd7HsW314bCtvE16LTLYkM?dt=1113
|
|
|
unholycactus
Legendary
Offline
Activity: 1078
Merit: 1024
|
|
June 06, 2017, 10:29:05 PM |
|
If you have access to your router, you can see the list of devices connected to it. Steps for that depend on the model.
Once you've identified which one is your miner, you can type that IP address to connect to it.
|
|
|
|
Hannu (OP)
|
|
June 08, 2017, 04:33:22 AM |
|
If you have access to your router, you can see the list of devices connected to it. Steps for that depend on the model.
Once you've identified which one is your miner, you can type that IP address to connect to it.
Now its not even rise online hashing mode. What i can do for it? Power broken? "Beep Beep Beep" Seems some signs of life.
|
BTC: 3Qnnx4cu45Gx4WcksNCnBPu3TaUZ5sKkLo LTC: LYX1ZH7f4qcXq52AzA6grUYDfDngVz7BEi XRP: rLrbZMJDdL8eQd7HsW314bCtvE16LTLYkM?dt=1113
|
|
|
Hockeybum
Member
Offline
Activity: 113
Merit: 31
|
|
June 08, 2017, 06:28:31 AM |
|
Where did you get the default IP address info? Was it written on the S5 and did you buy it used? If so, the ip address probably has changed.
The default setup in my S9 is set to dhcp to get an IP address from the router. You have to do what unholycactus said. Look up your router model and find out how to access the device list. Mine will say something like 192.168.1.xxx/antminer where xxx are additional numbers.
I haven't owned my S9s long enough to know what beeps you are talking about. Are both fans spinning up?
|
|
|
|
Hannu (OP)
|
|
June 08, 2017, 02:44:26 PM |
|
Where did you get the default IP address info? Was it written on the S5 and did you buy it used? If so, the ip address probably has changed.
The default setup in my S9 is set to dhcp to get an IP address from the router. You have to do what unholycactus said. Look up your router model and find out how to access the device list. Mine will say something like 192.168.1.xxx/antminer where xxx are additional numbers.
I haven't owned my S9s long enough to know what beeps you are talking about. Are both fans spinning up?
Yes i buy it one cereal guy, it worked earlyer without any problems and new firmware worked correctly. Now it just beeping. And not working. I hard reset it. Something wrong with power too i dont know what. No both fans not spinning not power and antminer.
|
BTC: 3Qnnx4cu45Gx4WcksNCnBPu3TaUZ5sKkLo LTC: LYX1ZH7f4qcXq52AzA6grUYDfDngVz7BEi XRP: rLrbZMJDdL8eQd7HsW314bCtvE16LTLYkM?dt=1113
|
|
|
Hannu (OP)
|
|
June 08, 2017, 06:07:04 PM Last edit: June 08, 2017, 06:24:18 PM by Hannu |
|
Where did you get the default IP address info? Was it written on the S5 and did you buy it used? If so, the ip address probably has changed.
The default setup in my S9 is set to dhcp to get an IP address from the router. You have to do what unholycactus said. Look up your router model and find out how to access the device list. Mine will say something like 192.168.1.xxx/antminer where xxx are additional numbers.
I haven't owned my S9s long enough to know what beeps you are talking about. Are both fans spinning up?
I look MS dos command ip config/all i use gateway what shows in the list, still i cannot access my miner. Now it stops to *beep* *beep* when i connect it to configure.
|
BTC: 3Qnnx4cu45Gx4WcksNCnBPu3TaUZ5sKkLo LTC: LYX1ZH7f4qcXq52AzA6grUYDfDngVz7BEi XRP: rLrbZMJDdL8eQd7HsW314bCtvE16LTLYkM?dt=1113
|
|
|
Hannu (OP)
|
|
June 08, 2017, 07:56:25 PM |
|
If you have access to your router, you can see the list of devices connected to it. Steps for that depend on the model.
Once you've identified which one is your miner, you can type that IP address to connect to it.
Yess! Now configure page is showing, i try to boot it many times but it still keeping that *beep* *beep* *beep* -Sound What i can do for it? Clusters dont rising temperature and cooling fans not running?
|
BTC: 3Qnnx4cu45Gx4WcksNCnBPu3TaUZ5sKkLo LTC: LYX1ZH7f4qcXq52AzA6grUYDfDngVz7BEi XRP: rLrbZMJDdL8eQd7HsW314bCtvE16LTLYkM?dt=1113
|
|
|
unholycactus
Legendary
Offline
Activity: 1078
Merit: 1024
|
|
June 08, 2017, 08:08:49 PM |
|
If you have access to your router, you can see the list of devices connected to it. Steps for that depend on the model.
Once you've identified which one is your miner, you can type that IP address to connect to it.
Yess! Now configure page is showing, i try to boot it many times but it still keeping that *beep* *beep* *beep* -Sound What i can do for it? Clusters dont rising temperature and cooling fans not running? Is the miner setup to a pool? The beeping sound means it cannot connect to the internet or the pool. The fans won't run fast since you aren't mining to begin with. Review your pool configuration.
|
|
|
|
Hannu (OP)
|
|
June 08, 2017, 08:31:43 PM |
|
If you have access to your router, you can see the list of devices connected to it. Steps for that depend on the model.
Once you've identified which one is your miner, you can type that IP address to connect to it.
Yess! Now configure page is showing, i try to boot it many times but it still keeping that *beep* *beep* *beep* -Sound What i can do for it? Clusters dont rising temperature and cooling fans not running? Is the miner setup to a pool? The beeping sound means it cannot connect to the internet or the pool. The fans won't run fast since you aren't mining to begin with. Review your pool configuration. Earlyer i dont have any problems with hashing bitcoins. Now powerfans and minerfans not working and AntMiner not hashing bitcoins. Pool config seems to be okay (i look web interface), something is wrong.
|
BTC: 3Qnnx4cu45Gx4WcksNCnBPu3TaUZ5sKkLo LTC: LYX1ZH7f4qcXq52AzA6grUYDfDngVz7BEi XRP: rLrbZMJDdL8eQd7HsW314bCtvE16LTLYkM?dt=1113
|
|
|
Hannu (OP)
|
|
June 08, 2017, 10:38:34 PM |
|
If you have access to your router, you can see the list of devices connected to it. Steps for that depend on the model.
Once you've identified which one is your miner, you can type that IP address to connect to it.
Yess! Now configure page is showing, i try to boot it many times but it still keeping that *beep* *beep* *beep* -Sound What i can do for it? Clusters dont rising temperature and cooling fans not running? Is the miner setup to a pool? The beeping sound means it cannot connect to the internet or the pool. The fans won't run fast since you aren't mining to begin with. Review your pool configuration. Earlyer i dont have any problems with hashing bitcoins. Now powerfans and minerfans not working and AntMiner not hashing bitcoins. Pool config seems to be okay (i look web interface), something is wrong. Now its working! Thank you!
|
BTC: 3Qnnx4cu45Gx4WcksNCnBPu3TaUZ5sKkLo LTC: LYX1ZH7f4qcXq52AzA6grUYDfDngVz7BEi XRP: rLrbZMJDdL8eQd7HsW314bCtvE16LTLYkM?dt=1113
|
|
|
|