[AUCTION] ASICMINER Blade Mounting Adapter Set

[jerboa]

I have ten sets (of two each) available to ship upon completion of this auction:

http://gifcountdown.com/europe-guernsey/1370714400/fdfdfd/474747/fdfdfd/333333/ffff00/true/counter.gif

Escrow by reputable member of the community accepted.

FREE SHIPPING worldwide.

https://i.imgur.com/JIVVUNm.jpg

https://i.imgur.com/ETvwyF6.jpg

https://i.imgur.com/XiIfHUb.jpg

- Suitable for one BE Blade or chainable
- Maintains 55mm of space between blades
- 4mm holes for fastening

Questions?

[jerboa]

Can't seem to edit my post. I forgot to mention minimum increment is 0.01 BTC.

[pvtbrutus]

3D printing FTW.

Too bad i don't have any blades  .

[biganth]

Minimum bid?

[jerboa]

Minimum bid?

No minimum!

[rammy2k2]

1@ 0.01 BTC

[rammy2k2]

Question : wont that plastic melt if the blade gets too hot ?

[jerboa]

Question : wont that plastic melt if the blade gets too hot ?

This plastic starts to get weak at ~100C. The melting point is 220C. I hope you don't run your blade at these temps 

[rammy2k2]

Question : wont that plastic melt if the blade gets too hot ?

This plastic starts to get weak at ~100C. The melting point is 220C. I hope you don't run your blade at these temps 

ok, cool .. well .. i placed my bid

[WinTame2012]

1@0.01 BTC

[mc_lovin]

8 @ 0.01

[dogie]

Is it ABS? Should probably have set a decent min This thread made me procrastinate for 4 1/2 hours remounting my blades in a new vertical windtunnel mode

[Xian01]

I was thinking of building a mount out of wooden dowels, but then I had nightmares of it possibly catching fire and killing me in my sleep 

[newguy05]

this would be perfect if you can redesign it and add additional mount for 2x 120mm fan in front of the heatsink similar to dogie's original setup photo. I didnt realize how big a pain in the **** it is to get this thing vertical then put 2 fans in front of it without touching the heatsink...

legos was my solution...

[jerboa]

Is it ABS? Should probably have set a decent min This thread made me procrastinate for 4 1/2 hours remounting my blades in a new vertical windtunnel mode

It is made from a type of polylactide which has approximately the same melting point as ABS but ABS starts to get weaker at a lower temperature (~50C I believe).

As to the decent min price comment, I am counting on the power of the free market which I will honor even at 0.01. If the price ends up too low I won't produce anymore.

[jerboa]

this would be perfect if you can redesign it and add additional mount for 2x 120mm fan in front of the heatsink similar to dogie's original setup photo. I didnt realize how big a pain in the **** it is to get this thing vertical then put 2 fans in front of it without touching the heatsink...

legos was my solution...

I have an idea for a fan mounting solution which would be separate (but compatible) from this but will wait to see the response for this item first.

[rammy2k2]

updating my bid to 2 @ 0.01

[dogie]

this would be perfect if you can redesign it and add additional mount for 2x 120mm fan in front of the heatsink similar to dogie's original setup photo. I didnt realize how big a pain in the **** it is to get this thing vertical then put 2 fans in front of it without touching the heatsink...

legos was my solution...

This is my newest newest setup now, rev 7 I think xD Wind tunnel design helps a LOT, conveys all the heat up and away. Everything much cooler and with lower fan speeds.

[ajk]

hi,

8@.02

please and thank you!

[Ajay]

4 @ 0.2