|
hotwired007 (OP)
|
 |
October 24, 2017, 01:46:34 PM |
|
I'm prototyping some 3D printed GPU mounts (singular GPU) - my own design (not the one from thingiverse!) I'm not sure on prices atm but i can do them in most colours (PLA atm) Would anyone be interested? Pics below:    |
This account was hacked & possibly sold during the period of August 1st and October 24th 2017.
Anything done or said in this period wasnt me.
Many thanks to Cyrus for his help restoring access to my account.
|
|
|
|
|
|
|
|
|
|
"There should not be any signed int. If you've found a signed int
somewhere, please tell me (within the next 25 years please) and I'll
change it to unsigned int." -- Satoshi
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
|
|
|
|
floppydisk
Jr. Member
 Offline
Activity: 92
Merit: 1
|
|
October 25, 2017, 04:51:03 AM |
|
Hi, what's the temperature rating of material in use ?
|
|
|
|
|
|
gt_addict
|
|
October 25, 2017, 06:44:27 AM |
|
They look good. What would the price be?
|
**SUPPORT SIDEHACK** Miner Development Donations to: 1BURGERAXHH6Yi6LRybRJK7ybEm5m5HwTr
Donations/Tips to:- 1GTADDicTXD1uachKKgW24DZDxDGhSMdRa
Join Bitconnect: https://bitconnect.co/?ref=gtaddict
|
|
|
|
hotwired007 (OP)
|
|
October 25, 2017, 10:05:32 AM |
|
Hi, what's the temperature rating of material in use ?
The plastic melts at around 190 degrees celcius. If your GPU gets that hot you have a problem  |
This account was hacked & possibly sold during the period of August 1st and October 24th 2017.
Anything done or said in this period wasnt me.
Many thanks to Cyrus for his help restoring access to my account.
|
|
|
|
hotwired007 (OP)
|
|
October 25, 2017, 10:06:50 AM |
|
They look good. What would the price be?
I'm not sure yet - that one is a prototype of 2 but i wondered if anyone would be interested - make an offer? I accept BTC, LTC, ETH and GBP |
This account was hacked & possibly sold during the period of August 1st and October 24th 2017.
Anything done or said in this period wasnt me.
Many thanks to Cyrus for his help restoring access to my account.
|
|
|
floppydisk
Jr. Member
Offline
Activity: 92
Merit: 1
|
|
October 25, 2017, 10:31:20 AM |
|
Hi, what's the temperature rating of material in use ?
The plastic melts at around 190 degrees celcius. If your GPU gets that hot you have a problem Yup, 3D printing is new for me, but PLA remain 'rigid' up to 55-60° (so called glass transition temperature). |
|
|
|
|
|
hotwired007 (OP)
|
|
October 25, 2017, 11:22:23 AM |
|
Hi, what's the temperature rating of material in use ?
The plastic melts at around 190 degrees celcius. If your GPU gets that hot you have a problem Yup, 3D printing is new for me, but PLA remain 'rigid' up to 55-60° (so called glass transition temperature). From what i have read online and experinced with my prototype - the plastic is fully capable of safely running as it is however i will be annealing the model to heat seal and increase the strength. https://rigid.ink/blogs/news/how-to-anneal-your-3d-prints-for-strength |
This account was hacked & possibly sold during the period of August 1st and October 24th 2017.
Anything done or said in this period wasnt me.
Many thanks to Cyrus for his help restoring access to my account.
|
|
|
|
hotwired007 (OP)
|
|
November 28, 2017, 10:05:52 AM |
|
Been running my RX 480 in an unannealed print since posting this and not had any issues with deforming or anthing.
I have redesigned it to make the base stronger a bit longer so that i shouldnt need any additional support on the rear of the cards (however will still include it)
|
This account was hacked & possibly sold during the period of August 1st and October 24th 2017.
Anything done or said in this period wasnt me.
Many thanks to Cyrus for his help restoring access to my account.
|
|
|
jenia1
Sr. Member
Offline
Activity: 504
Merit: 267
HashWare - Mining solutions for everyone!
|
|
November 28, 2017, 09:29:29 PM |
|
price?
|
|
|
|
|
cptdome1
|
|
November 29, 2017, 03:12:46 AM |
|
these look pretty cool. are you able to ship to USA? how much for one?
|
|
|
|
|
|
hotwired007 (OP)
|
|
December 01, 2017, 01:29:40 PM |
|
Still not decided on price - the main cost is the time take to print one.
offers?
|
This account was hacked & possibly sold during the period of August 1st and October 24th 2017.
Anything done or said in this period wasnt me.
Many thanks to Cyrus for his help restoring access to my account.
|
|
|
|
cavaliersrus
|
|
December 18, 2017, 04:12:23 PM |
|
i have a 3d printer and would like to print a few ... i cannot see your pictures at this time for some reason ... the ones i would print would not be for sale as i do not beleave in stealing another persons creativity... but i do understand if you would not like to release the .stl file
|
|
|
|
|
Commie
|
|
December 19, 2017, 11:39:00 AM |
|
Looks nice! I'd buy some but I live in SE Asia so shipping cost would kill all the fun. Would too appreiate an .stl file, if possible.
|
|
|
|
|
