RfBTC (OP)
Member
 Offline
Activity: 68
Merit: 10
|
 |
December 08, 2017, 12:50:09 AM |
|
|
|
|
|
|
|
|
|
|
|
There are several different types of Bitcoin clients. The most secure are full nodes like Bitcoin Core, but full nodes are more resource-heavy, and they must do a lengthy initial syncing process. As a result, lightweight clients with somewhat less security are commonly used.
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
|
|
|
|
bsp
Jr. Member
Offline
Activity: 40
Merit: 7
|
|
December 08, 2017, 12:59:41 AM |
|
|
|
|
|
|
|
VRobb
|
|
December 08, 2017, 01:09:30 AM |
|
What psu are you using?
|
I don't believe in superstition because it's bad luck: 13thF1oor6CAwyzyxXPNnRvu3nhhYeqZdc
These aren't the Droids you're looking for: S5 & S7 (Sold), R4B2, R4B4 (RIP), 2x S9 obsolete, 2xS15-28, S17-56, S17-70
Pushing a whopping 1/5 PH! Oh The SPEED!!!
|
|
|
RfBTC (OP)
Member
Offline
Activity: 68
Merit: 10
|
|
December 08, 2017, 04:47:02 AM |
|
Hi guys.... in the log file.... it's appear " ASIC RT error: (asic index start from 1-63) " .
PSU is APW3++ (1600W) BITMAIN Official
Hard Reset you mean the button in the front ? thanks
|
|
|
|
|
bsp
Jr. Member
Offline
Activity: 40
Merit: 7
|
|
December 08, 2017, 06:36:56 AM |
|
Hi guys.... in the log file.... it's appear " ASIC RT error: (asic index start from 1-63) " .
PSU is APW3++ (1600W) BITMAIN Official
Hard Reset you mean the button in the front ? thanks
There are 3 ways to reset S9. I gave link earlier: https://enforum.bitmain.com/bbs/topics/3957Use the last version (Power off, power up while holding IP button for 5 seconds, release - unit restarts with factory settings) I hope it helps. |
|
|
|
|
majdi105
Newbie
Offline
Activity: 64
Merit: 0
|
|
December 08, 2017, 10:57:45 AM |
|
just change the pool and fill all the 3 pool
|
|
|
|
|
RfBTC (OP)
Member
Offline
Activity: 68
Merit: 10
|
|
December 08, 2017, 03:40:23 PM |
|
Hi , guys my S9 AntMiner version its has the SD card slot on the left of the Ethernet interface. I have tried Soft-Restore and IP Reporter Restore and its keep no showing-data un Miner Status Tab  Pool data are 3 slots filled and in Kernel Log appear this..... bmminer not found= 1876 root 0:00 grep bmminer
bmminer not found, restart bmminer ...
bmminer not found=21834 root 0:00 grep bmminer
bmminer not found, restart bmminer ...
bmminer not found= 8881 root 0:00 grep bmminer
bmminer not found, restart bmminer ... Miner keep restarting in a loop ! Any idea thanks!  |
|
|
|
|
bsp
Jr. Member
Offline
Activity: 40
Merit: 7
|
|
December 09, 2017, 05:32:50 AM |
|
Try to connect Miner DIRECTLY to your main internet Router!!!
Without switch or other secondary device. Directly into your main router.
|
|
|
|
|
|
VRobb
|
|
December 09, 2017, 05:37:32 AM |
|
Pretty obvious you're missing files needed to run the miner. Says so right in your kernel log, "bmminer not found"
What bsp says is irrelevant since you're not fully booting up.
|
I don't believe in superstition because it's bad luck: 13thF1oor6CAwyzyxXPNnRvu3nhhYeqZdc
These aren't the Droids you're looking for: S5 & S7 (Sold), R4B2, R4B4 (RIP), 2x S9 obsolete, 2xS15-28, S17-56, S17-70
Pushing a whopping 1/5 PH! Oh The SPEED!!!
|
|
|
RfBTC (OP)
Member
Offline
Activity: 68
Merit: 10
|
|
December 09, 2017, 02:50:43 PM |
|
Try to connect Miner DIRECTLY to your main internet Router!!!
Without switch or other secondary device. Directly into your main router.
I dont think that will be de solution.... i have L3+ and D3 connected with switch.... and works perfectly... L3+ / D3 has Cgminer by default.... each time i make IP Report Reset, its works and my internal S9 IP is different, the matter is not the connection The matter is the BMminer, someone could got another alternative solution than bmminer-cgminer492 "Zwilla" update ? thanks |
|
|
|
|
|
cableiso
|
|
December 09, 2017, 03:00:54 PM |
|
Grep bmminer not found means it crashed upon start of mining. This is a popular problem these days, and I suspect it's a power supply issue.
Are you using apw3 on 110v?
|
|
|
|
|
|
