Antminer S9 stopped working completely after a restart - No Red led on 3 Asics

[lirankoren]

Hi All.  I am wondering if anyone seen this problem before.  I have antminer S9 who was working properly and all of his cards were appearing in the Status Tab.  The temperatures were high so I turn it off for a short period of time, and when I turned it on none of the Asic Chips would show in Status, I tried Hard Reset, Changing the Pools, and nothing was a success.  I noticed that when I turn on the Miner the Red Leds which usually appears on the 3 Asic Cards are no longer turning ON.  They are off at all time.  I am able to access the miner, and I can Ping from the Miner but none of the Card would come up and it will stay like this forever.  I tried one firmware upgrade but that did not change anything.   I am wondering if my miner and its 3 asics cards are completely dead?  I hope someone can help.

Here is a video that demonstrates the issue

https://www.dropbox.com/s/cyynnzmw3ga3q8q/VID-20180215-WA0072.mp4?dl=0

here is the kernel log (not sure if it means anything)

Code:

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.0-xilinx-ge8a2f71-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #82 SMP PREEMPT Tue May 16 19:49:53 CST 2017
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Xilinx Zynq
[    0.000000] cma: CMA: reserved 128 MiB at 27800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 258048
[    0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map e6fd8000
[    0.000000]   Normal zone: 1520 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 194560 pages, LIFO batch:31
[    0.000000]   HighMem zone: 496 pages used for memmap
[    0.000000]   HighMem zone: 63488 pages, LIFO batch:15
[    0.000000] PERCPU: Embedded 8 pages/cpu @e6fc0000 s9088 r8192 d15488 u32768
[    0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 256528
[    0.000000] Kernel command line: noinitrd mem=1008M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 884148K/1032192K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 148044K reserved, 253952K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06d1374   (6949 kB)
[    0.000000]       .init : 0xc06d2000 - 0xc0705380   ( 205 kB)
[    0.000000]       .data : 0xc0706000 - 0xc074cf78   ( 284 kB)
[    0.000000]        .bss : 0xc074cf84 - 0xc078d9fc   ( 259 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] ps7-slcr mapped to f0004000
[    0.000000] zynq_clock_init: clkc starts at f0004100
[    0.000000] Zynq clock init
[    0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[    0.000312] ps7-ttc #0 at f0006000, irq=43
[    0.000620] Console: colour dummy device 80x30
[    0.000657] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[    0.040210] pid_max: default: 32768 minimum: 301
[    0.040434] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.040455] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.042583] CPU: Testing write buffer coherency: ok
[    0.042929] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.042991] Setting up static identity map for 0x4c4b00 - 0x4c4b58
[    0.043215] L310 cache controller enabled
[    0.043235] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[    0.121037] CPU1: Booted secondary processor
[    0.210230] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.210359] Brought up 2 CPUs
[    0.210378] SMP: Total of 2 processors activated.
[    0.210386] CPU: All CPU(s) started in SVC mode.
[    0.211041] devtmpfs: initialized
[    0.213445] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.214651] regulator-dummy: no parameters
[    0.221876] NET: Registered protocol family 16
[    0.224161] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.226436] cpuidle: using governor ladder
[    0.226450] cpuidle: using governor menu
[    0.233856] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[    0.235372] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.235386] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.235503] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xf0080000
[    0.257269] bio: create slab <bio-0> at 0
[    0.258697] vgaarb: loaded
[    0.259411] SCSI subsystem initialized
[    0.260338] usbcore: registered new interface driver usbfs
[    0.260528] usbcore: registered new interface driver hub
[    0.260757] usbcore: registered new device driver usb
[    0.261294] media: Linux media interface: v0.10
[    0.261452] Linux video capture interface: v2.00
[    0.261692] pps_core: LinuxPPS API ver. 1 registered
[    0.261703] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.261827] PTP clock support registered
[    0.262187] EDAC MC: Ver: 3.0.0
[    0.263251] Advanced Linux Sound Architecture Driver Initialized.
[    0.266107] DMA-API: preallocated 4096 debug entries
[    0.266122] DMA-API: debugging enabled by kernel config
[    0.266198] Switched to clocksource arm_global_timer
[    0.287445] NET: Registered protocol family 2
[    0.288096] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.288192] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.288351] TCP: Hash tables configured (established 8192 bind 8192)
[    0.288413] TCP: reno registered
[    0.288434] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.288485] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.288763] NET: Registered protocol family 1
[    0.289115] RPC: Registered named UNIX socket transport module.
[    0.289128] RPC: Registered udp transport module.
[    0.289136] RPC: Registered tcp transport module.
[    0.289145] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.289158] PCI: CLS 0 bytes, default 64
[    0.289597] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.291632] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.293039] bounce pool size: 64 pages
[    0.293927] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.294135] msgmni has been set to 1486
[    0.294906] io scheduler noop registered
[    0.294919] io scheduler deadline registered
[    0.294961] io scheduler cfq registered (default)
[    0.302429] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[    0.302449] dma-pl330 f8003000.ps7-dma: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[    0.425809] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[    0.998873] console [ttyPS0] enabled
[    1.003168] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to f0068000
[    1.010822] [drm] Initialized drm 1.1.0 20060810
[    1.027800] brd: module loaded
[    1.037152] loop: module loaded
[    1.046781] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.052533] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.060493] libphy: XEMACPS mii bus: probed
[    1.064859] ------------- phy_id = 0x3625e62
[    1.069773] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[    1.078576] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.085209] ehci-pci: EHCI PCI platform driver
[    1.092463] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[    1.099297] usbcore: registered new interface driver usb-storage
[    1.106132] mousedev: PS/2 mouse device common for all mice
[    1.112254] i2c /dev entries driver
[    1.119234] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[    1.124713] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    1.130640] Xilinx Zynq CpuIdle Driver started
[    1.135493] sdhci: Secure Digital Host Controller Interface driver
[    1.141631] sdhci: Copyright(c) Pierre Ossman
[    1.145930] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.152765] mmc0: no vqmmc regulator found
[    1.156809] mmc0: no vmmc regulator found
[    1.196223] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[    1.204907] usbcore: registered new interface driver usbhid
[    1.210416] usbhid: USB HID core driver
[    1.215150] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.221447] nand: Micron MT29F2G08ABAEAWP
[    1.225416] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    1.231361] Bad block table found at page 131008, version 0x01
[    1.237581] Bad block table found at page 130944, version 0x01
[    1.243632] 3 ofpart partitions found on MTD device pl353-nand
[    1.249414] Creating 3 MTD partitions on "pl353-nand":
[    1.254510] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[    1.262558] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[    1.269896] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[    1.278831] TCP: cubic registered
[    1.282070] NET: Registered protocol family 17
[    1.286794] Registering SWP/SWPB emulation handler
[    1.292719] regulator-dummy: disabling
[    1.297080] UBI: attaching mtd1 to ubi0
[    1.822096] UBI: scanning is finished
[    1.833741] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[    1.840819] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.847581] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.854246] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.861123] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[    1.867104] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    1.874211] UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1134783803
[    1.883254] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[    1.892470] UBI: background thread "ubi_bgt0d" started, PID 1080
[    1.892476] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.896440] ALSA device list:
[    1.896444]   No soundcards found.
[    1.912799] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[    1.941807] UBIFS: recovery needed
[    2.003653] UBIFS: recovery completed
[    2.007338] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    2.013258] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    2.022392] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    2.032276] UBIFS: reserved for root: 0 bytes (0 KiB)
[    2.037316] UBIFS: media format: w4/r0 (latest is w4/r0), UUID B079DD56-06BB-4E31-8F5E-A6604F480DB2, small LPT model
[    2.048630] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    2.056034] devtmpfs: mounted
[    2.059167] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[    2.906337] random: dd urandom read with 0 bits of entropy available
[    3.306223] 
[    3.306223] bcm54xx_config_init
[    3.916236] 
[    3.916236] bcm54xx_config_init
[    7.917062] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[    7.923168] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
[   22.596887] In axi fpga driver!
[   22.599955] request_mem_region OK!
[   22.603346] AXI fpga dev virtual address is 0xf01fe000
[   22.608505] *base_vir_addr = 0x8c510
[   22.624236] In fpga mem driver!
[   22.627369] request_mem_region OK!
[   22.630875] fpga mem virtual address is 0xf3000000
[   23.426219] 
[   23.426219] bcm54xx_config_init
[   24.056235] 
[   24.056235] bcm54xx_config_init
[   28.057221] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[   28.063326] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
This is XILINX board. Totalram:       1039794176
Detect 1GB control board of XILINX
DETECT HW version=0008c510
miner ID : 80189401123b885c
Miner Type = S9
AsicType = 1387
real AsicNum = 63
use critical mode to search freq...
get PLUG ON=0x000000e0
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
set_reset_allhashboard = 0x0000ffff
Check chain[5] PIC fw version=0x03
Check chain[6] PIC fw version=0x03
Check chain[7] PIC fw version=0x03
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[5] has freq in PIC and will jump over...
Chain[5] has core num in PIC
Chain[5] ASIC[15] has core num=15
Chain[5] ASIC[17] has core num=1
Chain[5] ASIC[57] has core num=1
Check chain[5] PIC fw version=0x03
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[6] has freq in PIC and will jump over...
Chain[6] has core num in PIC
Chain[6] ASIC[54] has core num=15
Chain[6] ASIC[57] has core num=15
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[7] has freq in PIC and will jump over...
Chain[7] has core num in PIC
Chain[7] ASIC[14] has core num=1
Check chain[7] PIC fw version=0x03
get PIC voltage=125 on chain[5], value=870
get PIC voltage=125 on chain[6], value=870
get PIC voltage=125 on chain[7], value=870
set_reset_allhashboard = 0x00000000
chain[5] temp offset record: 62,0,0,0,0,0,35,28
chain[5] temp chip I2C addr=0x98
chain[5] has no middle temp, use special fix mode.
chain[6] temp offset record: 62,0,0,0,0,0,35,28
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
chain[7] temp offset record: 62,0,0,0,0,0,35,28
chain[7] temp chip I2C addr=0x98
chain[7] has no middle temp, use special fix mode.
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
CRC error counter=0
set command mode to VIL

--- check asic number
After Get ASIC NUM CRC error counter=0
set_baud=0
The min freq=700
set real timeout 52, need sleep=379392
After TEST CRC error counter=0
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
search freq for 1 times, completed chain = 3, total chain num = 3 
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
restart Miner chance num=2
waiting for receive_func to exit!
waiting for pic heart to exit!
bmminer not found= 1377 root       0:00 grep bmminer

bmminer not found, restart bmminer ...
This is user mode for mining
Detect 1GB control board of XILINX
Miner Type = S9
Miner compile time: Fri Nov 17 17:57:49 CST 2017 type: Antminer S9set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
miner ID : 80189401123b885c
set_reset_allhashboard = 0x0000ffff
Checking fans!get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800
get fan[5] speed=4800

[ccgllc]

I only see one fan showing up on that list.  Check and make sure both are working:  Unplug one and see if the other spins up.  Then switch and check.  You can not just look because the air moved by one would cause the blades on the other to spin.

[MinerMEDIC]

Chain[7] ASIC[14] has core num=1
That Is the error of interest to me because ALOT or the dead boards I'm getting have these errors.

[HagssFIN]

Based on the kernel log, it seems like a cooling fan issue or Bmminer issue.

Make sure your both front and rear cooling fans are working ok, and if it starts to look like a Bmminer issue, please install a new firmware by using the upgrade function in the miner web configuration page.

[castiel0504]

You can edit part of the your topic with this. http://prntscr.com/ifpjn5, and just paste your code between brackets. And for the fans, you can try to remove them both, and connect them to motherboard, one by one, and look are they spinning, much easier then messing with whole miner.

[fanatic26]

Id almost bet you have the 1117 firmware that is a total pile of crap. Roll it back to an older auto-tune and you should be good.

[HoleShot]

It is Nov17 firmware as it's shown in the log. I actually prefer this firmware over the prior versions.

The log stops at the fan check sequence. Go to the bottom of the log file to see this. Only Fan5 reported so you should check Fan2.

Heads up, fans are numbered 0 based in the log but 1 based on the Miner Status page. And anybody's guess how they are numbered on the controller.

[andygi]

Hi, equal problem in my S9 new hardware.(MARCH 2018 bach)
Today are aribed and after 30 minutes working weel at 13.5THs, i rebooted and don't work anymore.
3 harsh boards are red led off, some times, reboting the middel board leds are stand red.
I have a 2 BITMAIN 1600W PSU equalt results with 2 power supply.
Sistem don't run bmminer binary and no has rate.
Fans runs at full speed after some seconds of boot and don't decrease speed.

Kernel log:

Code:

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.0-xilinx-ge8a2f71-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #82 SMP PREEMPT Tue May 16 19:49:53 CST 2017
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Xilinx Zynq
[    0.000000] cma: CMA: reserved 128 MiB at 16800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 126976
[    0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map debd8000
[    0.000000]   Normal zone: 992 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 126976 pages, LIFO batch:31
[    0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[    0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 125984
[    0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 364356K/507904K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 143548K reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xdf800000 - 0xff000000   ( 504 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xdf000000   ( 496 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06d1374   (6949 kB)
[    0.000000]       .init : 0xc06d2000 - 0xc0705380   ( 205 kB)
[    0.000000]       .data : 0xc0706000 - 0xc074cf78   ( 284 kB)
[    0.000000]        .bss : 0xc074cf84 - 0xc078d9fc   ( 259 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] ps7-slcr mapped to df802000
[    0.000000] zynq_clock_init: clkc starts at df802100
[    0.000000] Zynq clock init
[    0.000016] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[    0.000313] ps7-ttc #0 at df804000, irq=43
[    0.000617] Console: colour dummy device 80x30
[    0.000649] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[    0.040212] pid_max: default: 32768 minimum: 301
[    0.040432] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.040451] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.042591] CPU: Testing write buffer coherency: ok
[    0.042930] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.042990] Setting up static identity map for 0x4c4b00 - 0x4c4b58
[    0.043215] L310 cache controller enabled
[    0.043235] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[    0.121038] CPU1: Booted secondary processor
[    0.210230] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.210361] Brought up 2 CPUs
[    0.210380] SMP: Total of 2 processors activated.
[    0.210388] CPU: All CPU(s) started in SVC mode.
[    0.211049] devtmpfs: initialized
[    0.213459] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.214669] regulator-dummy: no parameters
[    0.222329] NET: Registered protocol family 16
[    0.224564] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.226858] cpuidle: using governor ladder
[    0.226872] cpuidle: using governor menu
[    0.234325] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[    0.235844] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.235858] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.235972] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[    0.257674] bio: create slab <bio-0> at 0
[    0.259099] vgaarb: loaded
[    0.259800] SCSI subsystem initialized
[    0.260816] usbcore: registered new interface driver usbfs
[    0.260995] usbcore: registered new interface driver hub
[    0.261255] usbcore: registered new device driver usb
[    0.261796] media: Linux media interface: v0.10
[    0.261954] Linux video capture interface: v2.00
[    0.262202] pps_core: LinuxPPS API ver. 1 registered
[    0.262214] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.262337] PTP clock support registered
[    0.262692] EDAC MC: Ver: 3.0.0
[    0.263742] Advanced Linux Sound Architecture Driver Initialized.
[    0.266580] DMA-API: preallocated 4096 debug entries
[    0.266595] DMA-API: debugging enabled by kernel config
[    0.266671] Switched to clocksource arm_global_timer
[    0.287330] NET: Registered protocol family 2
[    0.287981] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.288038] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.288123] TCP: Hash tables configured (established 4096 bind 4096)
[    0.288167] TCP: reno registered
[    0.288185] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.288215] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.288462] NET: Registered protocol family 1
[    0.288765] RPC: Registered named UNIX socket transport module.
[    0.288777] RPC: Registered udp transport module.
[    0.288786] RPC: Registered tcp transport module.
[    0.288794] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.288807] PCI: CLS 0 bytes, default 64
[    0.289241] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.291251] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.293391] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.293575] msgmni has been set to 967
[    0.294359] io scheduler noop registered
[    0.294373] io scheduler deadline registered
[    0.294420] io scheduler cfq registered (default)
[    0.307123] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[    0.307143] dma-pl330 f8003000.ps7-dma: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[    0.429705] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[    0.997873] console [ttyPS0] enabled
[    1.002148] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[    1.009797] [drm] Initialized drm 1.1.0 20060810
[    1.026910] brd: module loaded
[    1.036218] loop: module loaded
[    1.045711] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.051696] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.059599] libphy: XEMACPS mii bus: probed
[    1.063973] ------------- phy_id = 0x3625e62
[    1.068933] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[    1.077605] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.084231] ehci-pci: EHCI PCI platform driver
[    1.091511] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[    1.098347] usbcore: registered new interface driver usb-storage
[    1.105180] mousedev: PS/2 mouse device common for all mice
[    1.111317] i2c /dev entries driver
[    1.118272] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[    1.123754] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    1.129666] Xilinx Zynq CpuIdle Driver started
[    1.134509] sdhci: Secure Digital Host Controller Interface driver
[    1.140688] sdhci: Copyright(c) Pierre Ossman
[    1.144956] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.151780] mmc0: no vqmmc regulator found
[    1.155792] mmc0: no vmmc regulator found
[    1.196690] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[    1.205392] usbcore: registered new interface driver usbhid
[    1.210908] usbhid: USB HID core driver
[    1.215607] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.221910] nand: Micron MT29F2G08ABAEAWP
[    1.225874] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    1.231821] Bad block table found at page 131008, version 0x01
[    1.238042] Bad block table found at page 130944, version 0x01
[    1.244091] 3 ofpart partitions found on MTD device pl353-nand
[    1.249874] Creating 3 MTD partitions on "pl353-nand":
[    1.254965] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[    1.263029] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[    1.270367] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[    1.279321] TCP: cubic registered
[    1.282555] NET: Registered protocol family 17
[    1.287268] Registering SWP/SWPB emulation handler
[    1.293148] regulator-dummy: disabling
[    1.297496] UBI: attaching mtd1 to ubi0
[    1.823251] UBI: scanning is finished
[    1.834897] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[    1.841980] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.848743] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.855407] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.862284] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[    1.868265] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    1.875372] UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1134783803
[    1.884415] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[    1.893631] UBI: background thread "ubi_bgt0d" started, PID 1080
[    1.893636] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.897593] ALSA device list:
[    1.897596]   No soundcards found.
[    1.914009] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[    1.971287] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    1.977250] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    1.986334] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    1.996241] UBIFS: reserved for root: 0 bytes (0 KiB)
[    2.001278] UBIFS: media format: w4/r0 (latest is w4/r0), UUID B079DD56-06BB-4E31-8F5E-A6604F480DB2, small LPT model
[    2.013019] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    2.020482] devtmpfs: mounted
[    2.023590] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[    2.862900] random: dd urandom read with 0 bits of entropy available
[    3.256695] 
[    3.256695] bcm54xx_config_init
[    3.866740] 
[    3.866740] bcm54xx_config_init
[    7.867535] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[    7.873641] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
[   25.417709] In axi fpga driver!
[   25.420774] request_mem_region OK!
[   25.424165] AXI fpga dev virtual address is 0xdf9fc000
[   25.429300] *base_vir_addr = 0x8c510
[   25.444611] In fpga mem driver!
[   25.447748] request_mem_region OK!
[   25.451255] fpga mem virtual address is 0xe2000000
[   26.256691] 
[   26.256691] bcm54xx_config_init
[   26.886690] 
[   26.886690] bcm54xx_config_init
[   30.887535] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[   30.893641] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
This is XILINX board. Totalram:       507527168
Detect 512MB control board of XILINX
DETECT HW version=0008c510
miner ID : 80641d2e2420881c
Miner Type = S9
AsicType = 1387
real AsicNum = 63
Find /tmp/searcherror: U6:1  The last log is below:
This is XILINX board. Totalram:       507527168
Detect 512MB control board of XILINX
DETECT HW version=0008c510
miner ID : 80641d2e2420881c
Miner Type = S9
AsicType = 1387
real AsicNum = 63
use critical mode to search freq...
get PLUG ON=0x000000e0
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
set_reset_allhashboard = 0x0000ffff
Check chain[5] PIC fw version=0x00
chain[5] PIC need restore ...
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
After restore: chain[5] PIC fw version=0x00

[HagssFIN]

@andygi
It seems like there is some issue with the PIC Firmware in the hash board (chain 5).
Can you unplug both data and power from that hash board?
It should be connected to the controller data port J5.

You could that way find out if the machine is able to operate when that hash board in unplugged.

If you end up finding that the hash board has this issue, you need a warranty repair.

Bitmain service guide: https://shop.bitmain.com/workOrderGuide.htm

EDIT:
You can see this picture as help to identify which has board is connected to J5.
I have marked each connector name location with blue marking.
https://i.imgur.com/Lnvbe0A.jpg

[gvsrusa]

I think it’s the control board. Remove the data and power connection for chain 5 and switch on the miner. It should work. If it is the case, replace the control board with new one. I hope this helps.

[HagssFIN]

Yeah, I'm guessing either the control board or the hash board connected to J5 is faulty.

[andygi]

Hi HagssFIN,

I due, equal results:

Code:

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.0-xilinx-ge8a2f71-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #82 SMP PREEMPT Tue May 16 19:49:53 CST 2017
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Xilinx Zynq
[    0.000000] cma: CMA: reserved 128 MiB at 16800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 126976
[    0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map debd8000
[    0.000000]   Normal zone: 992 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 126976 pages, LIFO batch:31
[    0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[    0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 125984
[    0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 364356K/507904K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 143548K reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xdf800000 - 0xff000000   ( 504 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xdf000000   ( 496 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06d1374   (6949 kB)
[    0.000000]       .init : 0xc06d2000 - 0xc0705380   ( 205 kB)
[    0.000000]       .data : 0xc0706000 - 0xc074cf78   ( 284 kB)
[    0.000000]        .bss : 0xc074cf84 - 0xc078d9fc   ( 259 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] ps7-slcr mapped to df802000
[    0.000000] zynq_clock_init: clkc starts at df802100
[    0.000000] Zynq clock init
[    0.000014] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[    0.000309] ps7-ttc #0 at df804000, irq=43
[    0.000618] Console: colour dummy device 80x30
[    0.000650] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[    0.040211] pid_max: default: 32768 minimum: 301
[    0.040432] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.040452] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.042584] CPU: Testing write buffer coherency: ok
[    0.042915] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.042973] Setting up static identity map for 0x4c4b00 - 0x4c4b58
[    0.043199] L310 cache controller enabled
[    0.043218] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[    0.121036] CPU1: Booted secondary processor
[    0.210230] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.210362] Brought up 2 CPUs
[    0.210380] SMP: Total of 2 processors activated.
[    0.210388] CPU: All CPU(s) started in SVC mode.
[    0.211051] devtmpfs: initialized
[    0.213465] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.214684] regulator-dummy: no parameters
[    0.222345] NET: Registered protocol family 16
[    0.224576] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.226874] cpuidle: using governor ladder
[    0.226888] cpuidle: using governor menu
[    0.234324] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[    0.235850] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.235864] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.235977] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[    0.257692] bio: create slab <bio-0> at 0
[    0.259117] vgaarb: loaded
[    0.259815] SCSI subsystem initialized
[    0.260913] usbcore: registered new interface driver usbfs
[    0.261112] usbcore: registered new interface driver hub
[    0.261348] usbcore: registered new device driver usb
[    0.261882] media: Linux media interface: v0.10
[    0.262046] Linux video capture interface: v2.00
[    0.262287] pps_core: LinuxPPS API ver. 1 registered
[    0.262299] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.262430] PTP clock support registered
[    0.262785] EDAC MC: Ver: 3.0.0
[    0.263846] Advanced Linux Sound Architecture Driver Initialized.
[    0.266705] DMA-API: preallocated 4096 debug entries
[    0.266719] DMA-API: debugging enabled by kernel config
[    0.266792] Switched to clocksource arm_global_timer
[    0.287904] NET: Registered protocol family 2
[    0.288559] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.288617] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.288701] TCP: Hash tables configured (established 4096 bind 4096)
[    0.288747] TCP: reno registered
[    0.288764] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.288795] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.289027] NET: Registered protocol family 1
[    0.289381] RPC: Registered named UNIX socket transport module.
[    0.289393] RPC: Registered udp transport module.
[    0.289401] RPC: Registered tcp transport module.
[    0.289410] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.289422] PCI: CLS 0 bytes, default 64
[    0.289853] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.291862] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.293946] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.294140] msgmni has been set to 967
[    0.294925] io scheduler noop registered
[    0.294938] io scheduler deadline registered
[    0.294991] io scheduler cfq registered (default)
[    0.307189] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[    0.307210] dma-pl330 f8003000.ps7-dma: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[    0.432988] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[    1.001244] console [ttyPS0] enabled
[    1.005510] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[    1.013154] [drm] Initialized drm 1.1.0 20060810
[    1.030227] brd: module loaded
[    1.039612] loop: module loaded
[    1.049221] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.054972] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.063072] libphy: XEMACPS mii bus: probed
[    1.067647] ------------- phy_id = 0x3625e62
[    1.072385] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[    1.081026] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.087679] ehci-pci: EHCI PCI platform driver
[    1.094894] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[    1.101709] usbcore: registered new interface driver usb-storage
[    1.108578] mousedev: PS/2 mouse device common for all mice
[    1.114667] i2c /dev entries driver
[    1.121624] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[    1.127200] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    1.133081] Xilinx Zynq CpuIdle Driver started
[    1.137959] sdhci: Secure Digital Host Controller Interface driver
[    1.144054] sdhci: Copyright(c) Pierre Ossman
[    1.148464] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.154191] mmc0: no vqmmc regulator found
[    1.158232] mmc0: no vmmc regulator found
[    1.196831] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[    1.205526] usbcore: registered new interface driver usbhid
[    1.211046] usbhid: USB HID core driver
[    1.215762] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.222052] nand: Micron MT29F2G08ABAEAWP
[    1.226023] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    1.231972] Bad block table found at page 131008, version 0x01
[    1.238210] Bad block table found at page 130944, version 0x01
[    1.244258] 3 ofpart partitions found on MTD device pl353-nand
[    1.250030] Creating 3 MTD partitions on "pl353-nand":
[    1.255131] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[    1.263189] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[    1.270504] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[    1.279477] TCP: cubic registered
[    1.282713] NET: Registered protocol family 17
[    1.287423] Registering SWP/SWPB emulation handler
[    1.293314] regulator-dummy: disabling
[    1.297651] UBI: attaching mtd1 to ubi0
[    1.823951] UBI: scanning is finished
[    1.835605] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[    1.842685] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.849448] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.856112] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.862989] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[    1.868970] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    1.876078] UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1134783803
[    1.885120] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[    1.894336] UBI: background thread "ubi_bgt0d" started, PID 1080
[    1.894342] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.898284] ALSA device list:
[    1.898288]   No soundcards found.
[    1.914694] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[    1.943698] UBIFS: recovery needed
[    2.042505] UBIFS: recovery completed
[    2.046164] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    2.052115] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    2.061221] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    2.071110] UBIFS: reserved for root: 0 bytes (0 KiB)
[    2.076139] UBIFS: media format: w4/r0 (latest is w4/r0), UUID B079DD56-06BB-4E31-8F5E-A6604F480DB2, small LPT model
[    2.087450] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    2.094858] devtmpfs: mounted
[    2.097983] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[    2.935918] random: dd urandom read with 0 bits of entropy available
[    3.326829] 
[    3.326829] bcm54xx_config_init
[    3.936838] 
[    3.936838] bcm54xx_config_init
[    7.937672] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[    7.943773] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
[   25.222130] In axi fpga driver!
[   25.225204] request_mem_region OK!
[   25.228626] AXI fpga dev virtual address is 0xdf9fc000
[   25.233701] *base_vir_addr = 0x8c510
[   25.249251] In fpga mem driver!
[   25.252321] request_mem_region OK!
[   25.255882] fpga mem virtual address is 0xe2000000
[   26.056857] 
[   26.056857] bcm54xx_config_init
[   26.686843] 
[   26.686843] bcm54xx_config_init
[   30.687670] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[   30.693773] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
This is XILINX board. Totalram:       507527168
Detect 512MB control board of XILINX
DETECT HW version=0008c510
miner ID : 80641d2e2420881c
Miner Type = S9
AsicType = 1387
real AsicNum = 63
Find /tmp/searcherror: U6:1  The last log is below:
This is XILINX board. Totalram:       507527168
Detect 512MB control board of XILINX
DETECT HW version=0008c510
miner ID : 80641d2e2420881c
Miner Type = S9
AsicType = 1387
real AsicNum = 63
use critical mode to search freq...
get PLUG ON=0x000000e0
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
set_reset_allhashboard = 0x0000ffff
Check chain[5] PIC fw version=0x00
chain[5] PIC need restore ...
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
After restore: chain[5] PIC fw version=0x00

J6 (Chain 6) only connected seem work fine:

Code:

[   25.215585] In fpga mem driver!
[   25.218722] request_mem_region OK!
[   25.222220] fpga mem virtual address is 0xe2000000
[   26.017029] 
[   26.017029] bcm54xx_config_init
[   26.647044] 
[   26.647044] bcm54xx_config_init
[   30.647879] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[   30.653984] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
This is XILINX board. Totalram:       507527168
Detect 512MB control board of XILINX
DETECT HW version=0008c510
miner ID : 80641d2e2420881c
Miner Type = S9
AsicType = 1387
real AsicNum = 63
use critical mode to search freq...
get PLUG ON=0x00000040
Find hashboard on Chain[6]
set_reset_allhashboard = 0x0000ffff
Check chain[6] PIC fw version=0x03
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[6] has freq in PIC and will jump over...
Chain[6] has core num in PIC
Chain[6] ASIC[39] has core num=1
Check chain[6] PIC fw version=0x03
get PIC voltage=6 on chain[6], value=940
set_reset_allhashboard = 0x00000000
chain[6] temp offset record: 62,0,0,0,0,0,35,28
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
CRC error counter=0
set command mode to VIL

--- check asic number
After Get ASIC NUM CRC error counter=0
set_baud=0
The min freq=700
set real timeout 52, need sleep=379392
After TEST CRC error counter=0
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
search freq for 1 times, completed chain = 1, total chain num = 1 
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
restart Miner chance num=2
waiting for receive_func to exit!
waiting for pic heart to exit!
bmminer not found= 1364 root       0:00 grep bmminer

bmminer not found, restart bmminer ...
This is user mode for mining
Detect 512MB control board of XILINX
Miner Type = S9
Miner compile time: Fri Nov 17 17:57:49 CST 2017 type: Antminer S9set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
miner ID : 80641d2e2420881c
set_reset_allhashboard = 0x0000ffff
Checking fans!get fan[2] speed=4560
get fan[2] speed=4560
get fan[2] speed=4560
get fan[2] speed=4560
get fan[2] speed=4560
get fan[2] speed=4560
get fan[2] speed=4560
get fan[2] speed=4560
get fan[2] speed=4560
get fan[5] speed=6120
get fan[2] speed=4560
get fan[5] speed=6120
get fan[2] speed=4560
get fan[5] speed=6120
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J7] has backup chain_voltage=870
Check chain[6] PIC fw version=0x03
Chain[J7] orignal chain_voltage_pic=6 value=940
Chain[J7] will use backup chain_voltage_pic=870 [125]
Chain[J7] get working chain_voltage_pic=125
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
Chain[J7] has 63 asic
Chain[J7] has core num in PIC
Chain[J7] ASIC[39] has core num=1
miner total rate=4667GH/s fixed rate=4500GH/s
read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=650
Asic[ 0]:650 
Asic[ 1]:650 Asic[ 2]:650 Asic[ 3]:650 Asic[ 4]:650 Asic[ 5]:650 Asic[ 6]:650 Asic[ 7]:650 Asic[ 8]:650 
Asic[ 9]:650 Asic[10]:650 Asic[11]:650 Asic[12]:650 Asic[13]:650 Asic[14]:650 Asic[15]:650 Asic[16]:650 
Asic[17]:650 Asic[18]:650 Asic[19]:650 Asic[20]:650 Asic[21]:650 Asic[22]:650 Asic[23]:650 Asic[24]:650 
Asic[25]:650 Asic[26]:650 Asic[27]:650 Asic[28]:650 Asic[29]:650 Asic[30]:650 Asic[31]:650 Asic[32]:650 
Asic[33]:650 Asic[34]:650 Asic[35]:650 Asic[36]:650 Asic[37]:650 Asic[38]:650 Asic[39]:650 Asic[40]:650 
Asic[41]:650 Asic[42]:650 Asic[43]:650 Asic[44]:650 Asic[45]:650 Asic[46]:650 Asic[47]:650 Asic[48]:650 
Asic[49]:650 Asic[50]:650 Asic[51]:650 Asic[52]:650 Asic[53]:650 Asic[54]:650 Asic[55]:650 Asic[56]:650 
Asic[57]:650 Asic[58]:650 Asic[59]:650 Asic[60]:650 Asic[61]:650 Asic[62]:650 
Chain:6 max freq=650
Chain:6 min freq=650


Miner fix freq ...
read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=650
Asic[ 0]:650 
Asic[ 1]:650 Asic[ 2]:650 Asic[ 3]:650 Asic[ 4]:650 Asic[ 5]:650 Asic[ 6]:650 Asic[ 7]:650 Asic[ 8]:650 
Asic[ 9]:650 Asic[10]:650 Asic[11]:650 Asic[12]:650 Asic[13]:650 Asic[14]:650 Asic[15]:650 Asic[16]:650 
Asic[17]:650 Asic[18]:650 Asic[19]:650 Asic[20]:650 Asic[21]:650 Asic[22]:650 Asic[23]:650 Asic[24]:650 
Asic[25]:650 Asic[26]:650 Asic[27]:650 Asic[28]:650 Asic[29]:650 Asic[30]:650 Asic[31]:650 Asic[32]:650 
Asic[33]:650 Asic[34]:650 Asic[35]:650 Asic[36]:650 Asic[37]:650 Asic[38]:650 Asic[39]:650 Asic[40]:650 
Asic[41]:650 Asic[42]:650 Asic[43]:650 Asic[44]:650 Asic[45]:650 Asic[46]:650 Asic[47]:650 Asic[48]:650 
Asic[49]:650 Asic[50]:650 Asic[51]:650 Asic[52]:650 Asic[53]:650 Asic[54]:650 Asic[55]:650 Asic[56]:650 
Asic[57]:650 Asic[58]:650 Asic[59]:650 Asic[60]:650 Asic[61]:650 Asic[62]:650 
Chain:6 max freq=650
Chain:6 min freq=650

max freq = 650
set baud=1
Chain[J7] PIC temp offset=62,0,0,0,0,0,35,28
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
Chain[J7] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[6] chip[244] local:22 remote:25 offset:26 
Chain[J7] chip[244] get middle temp offset=26 typeID=55
Chain[J7] set working voltage=870 [125]
do heat board 8xPatten for 1 times
start send works on chain[6]
do read_temp_func once...
do check_asic_reg 0x08
Done check_asic_reg
do read temp on Chain[6]
Chain[6] Chip[62] TempTypeID=55 middle offset=26
Chain[6] Chip[62] local Temp=29
Chain[6] Chip[62] middle Temp=40
Special fix Chain[6] Chip[62] middle Temp = 44
Done read temp on Chain[6]
Set fixed fan speed=70
FAN PWM: 70
read_temp_func Done!
CRC error counter=0

[andygi]

Now connected, J7 and J6, works?? 

Code:

.
.
[   30.603875] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
This is XILINX board. Totalram:       507527168
Detect 512MB control board of XILINX
DETECT HW version=0008c510
miner ID : 80641d2e2420881c
Miner Type = S9
AsicType = 1387
real AsicNum = 63
use critical mode to search freq...
get PLUG ON=0x000000c0
Find hashboard on Chain[6]
Find hashboard on Chain[7]
set_reset_allhashboard = 0x0000ffff
Check chain[6] PIC fw version=0x03
Check chain[7] PIC fw version=0x03
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[6] has freq in PIC and will jump over...
Chain[6] has core num in PIC
Chain[6] ASIC[39] has core num=1
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[7] has freq in PIC and will jump over...
Chain[7] has core num in PIC
Chain[7] ASIC[37] has core num=1
Check chain[7] PIC fw version=0x03
get PIC voltage=125 on chain[6], value=870
get PIC voltage=6 on chain[7], value=940
set_reset_allhashboard = 0x00000000
chain[6] temp offset record: 62,0,0,0,0,0,35,28
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
chain[7] temp offset record: 62,0,0,0,0,0,35,28
chain[7] temp chip I2C addr=0x98
chain[7] has no middle temp, use special fix mode.
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
CRC error counter=0
set command mode to VIL

--- check asic number
After Get ASIC NUM CRC error counter=0
set_baud=0
The min freq=700
set real timeout 52, need sleep=379392
After TEST CRC error counter=0
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
search freq for 1 times, completed chain = 2, total chain num = 2 
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
restart Miner chance num=2
waiting for receive_func to exit!
waiting for pic heart to exit!
bmminer not found= 1373 root       0:00 grep bmminer

bmminer not found, restart bmminer ...
This is user mode for mining
Detect 512MB control board of XILINX
Miner Type = S9
Miner compile time: Fri Nov 17 17:57:49 CST 2017 type: Antminer S9set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
miner ID : 80641d2e2420881c
set_reset_allhashboard = 0x0000ffff
Checking fans!get fan[2] speed=4560
get fan[2] speed=4560
get fan[2] speed=4560
get fan[2] speed=4560
get fan[2] speed=4560
get fan[2] speed=4560
get fan[2] speed=4560
get fan[2] speed=4560
get fan[2] speed=4560
get fan[5] speed=6120
get fan[2] speed=4560
get fan[5] speed=6120
get fan[2] speed=4560
get fan[5] speed=6120
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J7] has backup chain_voltage=870
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J8] has backup chain_voltage=870
Check chain[7] PIC fw version=0x03
Chain[J7] orignal chain_voltage_pic=125 value=870
Chain[J8] orignal chain_voltage_pic=6 value=940
Chain[J8] will use backup chain_voltage_pic=870 [125]
Chain[J8] get working chain_voltage_pic=125
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
Chain[J7] has 63 asic
Chain[J8] has 63 asic
Chain[J7] has core num in PIC
Chain[J7] ASIC[39] has core num=1
Chain[J8] has core num in PIC
Chain[J8] ASIC[37] has core num=1
miner total rate=9335GH/s fixed rate=9000GH/s
read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=650
Asic[ 0]:650 
Asic[ 1]:650 Asic[ 2]:650 Asic[ 3]:650 Asic[ 4]:650 Asic[ 5]:650 Asic[ 6]:650 Asic[ 7]:650 Asic[ 8]:650 
Asic[ 9]:650 Asic[10]:650 Asic[11]:650 Asic[12]:650 Asic[13]:650 Asic[14]:650 Asic[15]:650 Asic[16]:650 
Asic[17]:650 Asic[18]:650 Asic[19]:650 Asic[20]:650 Asic[21]:650 Asic[22]:650 Asic[23]:650 Asic[24]:650 
Asic[25]:650 Asic[26]:650 Asic[27]:650 Asic[28]:650 Asic[29]:650 Asic[30]:650 Asic[31]:650 Asic[32]:650 
Asic[33]:650 Asic[34]:650 Asic[35]:650 Asic[36]:650 Asic[37]:650 Asic[38]:650 Asic[39]:650 Asic[40]:650 
Asic[41]:650 Asic[42]:650 Asic[43]:650 Asic[44]:650 Asic[45]:650 Asic[46]:650 Asic[47]:650 Asic[48]:650 
Asic[49]:650 Asic[50]:650 Asic[51]:650 Asic[52]:650 Asic[53]:650 Asic[54]:650 Asic[55]:650 Asic[56]:650 
Asic[57]:650 Asic[58]:650 Asic[59]:650 Asic[60]:650 Asic[61]:650 Asic[62]:650 
Chain:6 max freq=650
Chain:6 min freq=650

read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=650
Asic[ 0]:650 
Asic[ 1]:650 Asic[ 2]:650 Asic[ 3]:650 Asic[ 4]:650 Asic[ 5]:650 Asic[ 6]:650 Asic[ 7]:650 Asic[ 8]:650 
Asic[ 9]:650 Asic[10]:650 Asic[11]:650 Asic[12]:650 Asic[13]:650 Asic[14]:650 Asic[15]:650 Asic[16]:650 
Asic[17]:650 Asic[18]:650 Asic[19]:650 Asic[20]:650 Asic[21]:650 Asic[22]:650 Asic[23]:650 Asic[24]:650 
Asic[25]:650 Asic[26]:650 Asic[27]:650 Asic[28]:650 Asic[29]:650 Asic[30]:650 Asic[31]:650 Asic[32]:650 
Asic[33]:650 Asic[34]:650 Asic[35]:650 Asic[36]:650 Asic[37]:650 Asic[38]:650 Asic[39]:650 Asic[40]:650 
Asic[41]:650 Asic[42]:650 Asic[43]:650 Asic[44]:650 Asic[45]:650 Asic[46]:650 Asic[47]:650 Asic[48]:650 
Asic[49]:650 Asic[50]:650 Asic[51]:650 Asic[52]:650 Asic[53]:650 Asic[54]:650 Asic[55]:650 Asic[56]:650 
Asic[57]:650 Asic[58]:650 Asic[59]:650 Asic[60]:650 Asic[61]:650 Asic[62]:650 
Chain:7 max freq=650
Chain:7 min freq=650


Miner fix freq ...
read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=650
Asic[ 0]:650 
Asic[ 1]:650 Asic[ 2]:650 Asic[ 3]:650 Asic[ 4]:650 Asic[ 5]:650 Asic[ 6]:650 Asic[ 7]:650 Asic[ 8]:650 
Asic[ 9]:650 Asic[10]:650 Asic[11]:650 Asic[12]:650 Asic[13]:650 Asic[14]:650 Asic[15]:650 Asic[16]:650 
Asic[17]:650 Asic[18]:650 Asic[19]:650 Asic[20]:650 Asic[21]:650 Asic[22]:650 Asic[23]:650 Asic[24]:650 
Asic[25]:650 Asic[26]:650 Asic[27]:650 Asic[28]:650 Asic[29]:650 Asic[30]:650 Asic[31]:650 Asic[32]:650 
Asic[33]:650 Asic[34]:650 Asic[35]:650 Asic[36]:650 Asic[37]:650 Asic[38]:650 Asic[39]:650 Asic[40]:650 
Asic[41]:650 Asic[42]:650 Asic[43]:650 Asic[44]:650 Asic[45]:650 Asic[46]:650 Asic[47]:650 Asic[48]:650 
Asic[49]:650 Asic[50]:650 Asic[51]:650 Asic[52]:650 Asic[53]:650 Asic[54]:650 Asic[55]:650 Asic[56]:650 
Asic[57]:650 Asic[58]:650 Asic[59]:650 Asic[60]:650 Asic[61]:650 Asic[62]:650 
Chain:6 max freq=650
Chain:6 min freq=650

read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=650
Asic[ 0]:650 
Asic[ 1]:650 Asic[ 2]:650 Asic[ 3]:650 Asic[ 4]:650 Asic[ 5]:650 Asic[ 6]:650 Asic[ 7]:650 Asic[ 8]:650 
Asic[ 9]:650 Asic[10]:650 Asic[11]:650 Asic[12]:650 Asic[13]:650 Asic[14]:650 Asic[15]:650 Asic[16]:650 
Asic[17]:650 Asic[18]:650 Asic[19]:650 Asic[20]:650 Asic[21]:650 Asic[22]:650 Asic[23]:650 Asic[24]:650 
Asic[25]:650 Asic[26]:650 Asic[27]:650 Asic[28]:650 Asic[29]:650 Asic[30]:650 Asic[31]:650 Asic[32]:650 
Asic[33]:650 Asic[34]:650 Asic[35]:650 Asic[36]:650 Asic[37]:650 Asic[38]:650 Asic[39]:650 Asic[40]:650 
Asic[41]:650 Asic[42]:650 Asic[43]:650 Asic[44]:650 Asic[45]:650 Asic[46]:650 Asic[47]:650 Asic[48]:650 
Asic[49]:650 Asic[50]:650 Asic[51]:650 Asic[52]:650 Asic[53]:650 Asic[54]:650 Asic[55]:650 Asic[56]:650 
Asic[57]:650 Asic[58]:650 Asic[59]:650 Asic[60]:650 Asic[61]:650 Asic[62]:650 
Chain:7 max freq=650
Chain:7 min freq=650

max freq = 650
set baud=1
Chain[J7] PIC temp offset=62,0,0,0,0,0,35,28
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
Chain[J7] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[6] chip[244] local:23 remote:26 offset:26 
Chain[J7] chip[244] get middle temp offset=26 typeID=55
Chain[J8] PIC temp offset=62,0,0,0,0,0,35,28
chain[7] temp chip I2C addr=0x98
chain[7] has no middle temp, use special fix mode.
Chain[J8] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[7] chip[244] local:23 remote:26 offset:26 
Chain[J8] chip[244] get middle temp offset=26 typeID=55
Chain[J7] set working voltage=870 [125]
Chain[J8] set working voltage=870 [125]
do heat board 8xPatten for 1 times
start send works on chain[6]
start send works on chain[7]
get send work num :57456 on Chain[6]
get send work num :57456 on Chain[7]
wait recv nonce on chain[6]
wait recv nonce on chain[7]
get nonces on chain[6]
require nonce number:912
require validnonce number:57456
asic[00]=912	asic[01]=912	asic[02]=912	asic[03]=912	asic[04]=912	asic[05]=912	asic[06]=912	asic[07]=912	
asic[08]=912	asic[09]=912	asic[10]=912	asic[11]=912	asic[12]=912	asic[13]=912	asic[14]=912	asic[15]=912	
asic[16]=912	asic[17]=912	asic[18]=912	asic[19]=912	asic[20]=912	asic[21]=912	asic[22]=912	asic[23]=912	
asic[24]=912	asic[25]=912	asic[26]=912	asic[27]=912	asic[28]=912	asic[29]=912	asic[30]=912	asic[31]=912	
asic[32]=912	asic[33]=912	asic[34]=912	asic[35]=912	asic[36]=912	asic[37]=912	asic[38]=912	asic[39]=912	
asic[40]=912	asic[41]=912	asic[42]=912	asic[43]=912	asic[44]=912	asic[45]=912	asic[46]=912	asic[47]=912	
asic[48]=912	asic[49]=912	asic[50]=912	asic[51]=912	asic[52]=912	asic[53]=912	asic[54]=912	asic[55]=912	
asic[56]=912	asic[57]=912	asic[58]=912	asic[59]=912	asic[60]=912	asic[61]=912	asic[62]=912	


Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!



freq[00]=650	freq[01]=650	freq[02]=650	freq[03]=650	freq[04]=650	freq[05]=650	freq[06]=650	freq[07]=650	
freq[08]=650	freq[09]=650	freq[10]=650	freq[11]=650	freq[12]=650	freq[13]=650	freq[14]=650	freq[15]=650	
freq[16]=650	freq[17]=650	freq[18]=650	freq[19]=650	freq[20]=650	freq[21]=650	freq[22]=650	freq[23]=650	
freq[24]=650	freq[25]=650	freq[26]=650	freq[27]=650	freq[28]=650	freq[29]=650	freq[30]=650	freq[31]=650	
freq[32]=650	freq[33]=650	freq[34]=650	freq[35]=650	freq[36]=650	freq[37]=650	freq[38]=650	freq[39]=650	
freq[40]=650	freq[41]=650	freq[42]=650	freq[43]=650	freq[44]=650	freq[45]=650	freq[46]=650	freq[47]=650	
freq[48]=650	freq[49]=650	freq[50]=650	freq[51]=650	freq[52]=650	freq[53]=650	freq[54]=650	freq[55]=650	
freq[56]=650	freq[57]=650	freq[58]=650	freq[59]=650	freq[60]=650	freq[61]=650	freq[62]=650	

total valid nonce number:57456
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:26639
last_nonce_num:29040
get nonces on chain[7]
require nonce number:912
require validnonce number:57456
asic[00]=912	asic[01]=912	asic[02]=912	asic[03]=912	asic[04]=912	asic[05]=912	asic[06]=912	asic[07]=912	
asic[08]=912	asic[09]=912	asic[10]=912	asic[11]=912	asic[12]=912	asic[13]=912	asic[14]=912	asic[15]=912	
asic[16]=912	asic[17]=912	asic[18]=912	asic[19]=912	asic[20]=912	asic[21]=912	asic[22]=912	asic[23]=912	
asic[24]=912	asic[25]=912	asic[26]=912	asic[27]=912	asic[28]=912	asic[29]=912	asic[30]=912	asic[31]=912	
asic[32]=912	asic[33]=912	asic[34]=912	asic[35]=912	asic[36]=912	asic[37]=912	asic[38]=912	asic[39]=912	
asic[40]=912	asic[41]=912	asic[42]=912	asic[43]=912	asic[44]=912	asic[45]=912	asic[46]=912	asic[47]=912	
asic[48]=912	asic[49]=912	asic[50]=912	asic[51]=912	asic[52]=912	asic[53]=912	asic[54]=912	asic[55]=912	
asic[56]=912	asic[57]=912	asic[58]=912	asic[59]=912	asic[60]=912	asic[61]=912	asic[62]=912	


Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!



freq[00]=650	freq[01]=650	freq[02]=650	freq[03]=650	freq[04]=650	freq[05]=650	freq[06]=650	freq[07]=650	
freq[08]=650	freq[09]=650	freq[10]=650	freq[11]=650	freq[12]=650	freq[13]=650	freq[14]=650	freq[15]=650	
freq[16]=650	freq[17]=650	freq[18]=650	freq[19]=650	freq[20]=650	freq[21]=650	freq[22]=650	freq[23]=650	
freq[24]=650	freq[25]=650	freq[26]=650	freq[27]=650	freq[28]=650	freq[29]=650	freq[30]=650	freq[31]=650	
freq[32]=650	freq[33]=650	freq[34]=650	freq[35]=650	freq[36]=650	freq[37]=650	freq[38]=650	freq[39]=650	
freq[40]=650	freq[41]=650	freq[42]=650	freq[43]=650	freq[44]=650	freq[45]=650	freq[46]=650	freq[47]=650	
freq[48]=650	freq[49]=650	freq[50]=650	freq[51]=650	freq[52]=650	freq[53]=650	freq[54]=650	freq[55]=650	
freq[56]=650	freq[57]=650	freq[58]=650	freq[59]=650	freq[60]=650	freq[61]=650	freq[62]=650	

total valid nonce number:57456
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:26627
last_nonce_num:33868
chain[6]: All chip cores are opened OK!
Test Patten on chain[6]: OK!
chain[7]: All chip cores are opened OK!
Test Patten on chain[7]: OK!
setStartTimePoint total_tv_start_sys=141 total_tv_end_sys=142
restartNum = 2 , auto-reinit enabled...
do read_temp_func once...
do check_asic_reg 0x08

get RT hashrate from Chain[6]: (asic index start from 1-63)
Asic[01]=121.618 Asic[02]=113.984 Asic[03]=116.165 Asic[04]=115.444 Asic[05]=117.474 Asic[06]=115.444 Asic[07]=116.534 Asic[08]=116.198 
Asic[09]=116.819 Asic[10]=117.591 Asic[11]=115.125 Asic[12]=119.990 Asic[13]=116.014 Asic[14]=513.164 Asic[15]=115.712 Asic[16]=114.588 
Asic[17]=118.044 Asic[18]=115.293 Asic[19]=400.203 Asic[20]=118.984 Asic[21]=119.554 Asic[22]=112.558 Asic[23]=118.145 Asic[24]=113.548 
Asic[25]=116.752 Asic[26]=119.604 Asic[27]=117.893 Asic[28]=116.886 Asic[29]=131.617 Asic[30]=118.413 Asic[31]=111.383 Asic[32]=118.128 
Asic[33]=111.753 Asic[34]=114.487 Asic[35]=116.198 Asic[36]=265.801 Asic[37]=119.621 Asic[38]=120.108 Asic[39]=114.504 Asic[40]=116.081 
Asic[41]=115.477 Asic[42]=119.135 Asic[43]=115.964 Asic[44]=114.739 Asic[45]=664.595 Asic[46]=118.044 Asic[47]=116.568 Asic[48]=1559.01 
Asic[49]=112.273 Asic[50]=116.048 Asic[51]=115.695 Asic[52]=120.712 Asic[53]=116.886 Asic[54]=117.541 Asic[55]=117.255 Asic[56]=118.279 
Asic[57]=128.731 Asic[58]=115.561 Asic[59]=115.225 Asic[60]=115.527 Asic[61]=116.500 Asic[62]=115.125 Asic[63]=121.701 

get RT hashrate from Chain[7]: (asic index start from 1-63)
Asic[01]=117.289 Asic[02]=112.692 Asic[03]=113.514 Asic[04]=110.628 Asic[05]=116.182 Asic[06]=111.904 Asic[07]=114.638 Asic[08]=116.819 
Asic[09]=116.668 Asic[10]=114.252 Asic[11]=114.588 Asic[12]=115.997 Asic[13]=112.558 Asic[14]=484.727 Asic[15]=114.420 Asic[16]=111.702 
Asic[17]=116.870 Asic[18]=114.118 Asic[19]=114.907 Asic[20]=114.001 Asic[21]=117.776 Asic[22]=111.635 Asic[23]=252.547 Asic[24]=110.343 
Asic[25]=114.823 Asic[26]=116.266 Asic[27]=114.286 Asic[28]=113.212 Asic[29]=131.533 Asic[30]=114.403 Asic[31]=109.672 Asic[32]=112.357 
Asic[33]=111.333 Asic[34]=111.132 Asic[35]=115.578 Asic[36]=114.336 Asic[37]=117.172 Asic[38]=116.282 Asic[39]=112.122 Asic[40]=628.944 
Asic[41]=111.316 Asic[42]=119.621 Asic[43]=116.081 Asic[44]=114.621 Asic[45]=114.856 Asic[46]=119.168 Asic[47]=116.098 Asic[48]=1466.46 
Asic[49]=108.833 Asic[50]=113.044 Asic[51]=114.370 Asic[52]=116.584 Asic[53]=114.051 Asic[54]=116.198 Asic[55]=115.175 Asic[56]=376.245 
Asic[57]=127.741 Asic[58]=113.195 Asic[59]=118.178 Asic[60]=112.407 Asic[61]=214.714 Asic[62]=111.971 Asic[63]=118.749 
Check Chain[J7] ASIC RT error: (asic index start from 1-63)
Asic[01]=121.618000
Asic[02]=113.984000
Asic[03]=116.165000
Asic[04]=115.444000
Asic[05]=117.474000
Asic[06]=115.444000
Asic[07]=116.534000
Asic[08]=116.198000
Asic[09]=116.819000
Asic[10]=117.591000
Asic[11]=115.125000
Asic[12]=119.990000
Asic[13]=116.014000
Asic[14]=513.164000
Asic[15]=115.712000
Asic[16]=114.588000
Asic[17]=118.044000
Asic[18]=115.293000
Asic[19]=400.203000
Asic[20]=118.984000
Asic[21]=119.554000
Asic[22]=112.558000
Asic[23]=118.145000
Asic[24]=113.548000
Asic[25]=116.752000
Asic[26]=119.604000
Asic[27]=117.893000
Asic[28]=116.886000
Asic[29]=131.617000
Asic[30]=118.413000
Asic[31]=111.383000
Asic[32]=118.128000
Asic[33]=111.753000
Asic[34]=114.487000
Asic[35]=116.198000
Asic[36]=265.801000
Asic[37]=119.621000
Asic[38]=120.108000
Asic[39]=114.504000
Asic[40]=116.081000
Asic[41]=115.477000
Asic[42]=119.135000
Asic[43]=115.964000
Asic[44]=114.739000
Asic[45]=664.595000
Asic[46]=118.044000
Asic[47]=116.568000
Asic[48]=1559.010000
Asic[49]=112.273000
Asic[50]=116.048000
Asic[51]=115.695000
Asic[52]=120.712000
Asic[53]=116.886000
Asic[54]=117.541000
Asic[55]=117.255000
Asic[56]=118.279000
Asic[57]=128.731000
Asic[58]=115.561000
Asic[59]=115.225000
Asic[60]=115.527000
Asic[61]=116.500000
Asic[62]=115.125000
Asic[63]=121.701000
Check Chain[J8] ASIC RT error: (asic index start from 1-63)
Asic[01]=117.289000
Asic[02]=112.692000
Asic[03]=113.514000
Asic[04]=110.628000
Asic[05]=116.182000
Asic[06]=111.904000
Asic[07]=114.638000
Asic[08]=116.819000
Asic[09]=116.668000
Asic[10]=114.252000
Asic[11]=114.588000
Asic[12]=115.997000
Asic[13]=112.558000
Asic[14]=484.727000
Asic[15]=114.420000
Asic[16]=111.702000
Asic[17]=116.870000
Asic[18]=114.118000
Asic[19]=114.907000
Asic[20]=114.001000
Asic[21]=117.776000
Asic[22]=111.635000
Asic[23]=252.547000
Asic[24]=110.343000
Asic[25]=114.823000
Asic[26]=116.266000
Asic[27]=114.286000
Asic[28]=113.212000
Asic[29]=131.533000
Asic[30]=114.403000
Asic[31]=109.672000
Asic[32]=112.357000
Asic[33]=111.333000
Asic[34]=111.132000
Asic[35]=115.578000
Asic[36]=114.336000
Asic[37]=117.172000
Asic[38]=116.282000
Asic[39]=112.122000
Asic[40]=628.944000
Asic[41]=111.316000
Asic[42]=119.621000
Asic[43]=116.081000
Asic[44]=114.621000
Asic[45]=114.856000
Asic[46]=119.168000
Asic[47]=116.098000
Asic[48]=1466.460000
Asic[49]=108.833000
Asic[50]=113.044000
Asic[51]=114.370000
Asic[52]=116.584000
Asic[53]=114.051000
Asic[54]=116.198000
Asic[55]=115.175000
Asic[56]=376.245000
Asic[57]=127.741000
Asic[58]=113.195000
Asic[59]=118.178000
Asic[60]=112.407000
Asic[61]=214.714000
Asic[62]=111.971000
Asic[63]=118.749000
Done check_asic_reg
do read temp on Chain[6]
Chain[6] Chip[62] TempTypeID=55 middle offset=26
Chain[6] Chip[62] local Temp=49
Chain[6] Chip[62] middle Temp=58
Special fix Chain[6] Chip[62] middle Temp = 64
Done read temp on Chain[6]
do read temp on Chain[7]
Chain[7] Chip[62] TempTypeID=55 middle offset=26
Chain[7] Chip[62] local Temp=50
Chain[7] Chip[62] middle Temp=59
Special fix Chain[7] Chip[62] middle Temp = 65
Done read temp on Chain[7]
read_temp_func Done!
CRC error counter=0

I don't stand why now work, and some hours before no.

[HagssFIN]

Can you please connect a fully working hash board to the controller port J5?

If it is working ok, then I would say that the control board is ok.
And that there is one faulty hash board.

[andygi]

Can you please connect a fully working hash board to the controller port J5?

If it is working ok, then I would say that the control board is ok.
And that there is one faulty hash board.

Well, I conneted a faultiboard to J6 connector and error apears now in [Chain6]. Hasboard is the problem so.

[HagssFIN]

Ok. If you can get a good hash board work when connected to the controller port J5,
then you can be pretty much 100% that it is the bad hash board that is faulty.

So it is time to go through those Bitmain warranty repair instructions I posted earlier (see above).