dragonmike (OP)
|
|
February 21, 2018, 11:46:09 AM |
|
As always, one of my rigs started to act up whilst I was on holiday. One GPU would start showing 511C errors, crash the miner and the rig within a few sec. Seeing that this couldn't be fixed remotely I cut the power to that rig completely using the tp-link smart plug app and decided to address it when I got back. It was quite an easy diagnostic: https://flic.kr/p/ETFBZzFlimsy Chinese risers. Always make sure you got a few spares, and don't insist on powering up a failing rig remotely if you suspect there's a hardware/power error.
|
|
|
|
trippcheck
|
|
February 21, 2018, 12:44:27 PM |
|
dont use floppy cables for power risers
haha next time burning home
|
|
|
|
nc50lc
Legendary
Offline
Activity: 2562
Merit: 6236
Self-proclaimed Genius
|
|
February 21, 2018, 02:30:57 PM |
|
Seems like the heat came from the connector not the wires. Sometimes, these was caused by over-bending the connector resulting in stretched ends, equals high resistance between the wires and the metal contacts. The other wires look like heated by something thin, those aligned melted or scarred ring-like marks seems like bent around a metal edge for a while.
|
|
|
|
Rune_Coin
Copper Member
Newbie
Offline
Activity: 14
Merit: 0
|
|
February 21, 2018, 04:17:15 PM |
|
As always, one of my rigs started to act up whilst I was on holiday. One GPU would start showing 511C errors, crash the miner and the rig within a few sec. Seeing that this couldn't be fixed remotely I cut the power to that rig completely using the tp-link smart plug app and decided to address it when I got back.
It was quite an easy diagnostic:
https://[Suspicious link removed]/p/ETFBZz
Flimsy Chinese risers. Always make sure you got a few spares, and don't insist on powering up a failing rig remotely if you suspect there's a hardware/power error.
Always use MOLEX powered cables to avoid fire
|
|
|
|
SubutaiKHAN
Newbie
Offline
Activity: 15
Merit: 0
|
|
February 21, 2018, 05:51:34 PM |
|
It's always the connector, from my experience. They tend to be cheap and dangerous.
I switched out all my adaptors/connectors and use straight PSU to the riser, have never had a problem since.
|
|
|
|
hous26
|
|
February 21, 2018, 06:11:37 PM |
|
As always, one of my rigs started to act up whilst I was on holiday. One GPU would start showing 511C errors, crash the miner and the rig within a few sec. Seeing that this couldn't be fixed remotely I cut the power to that rig completely using the tp-link smart plug app and decided to address it when I got back.
It was quite an easy diagnostic:
https://[Suspicious link removed]/p/ETFBZz
Flimsy Chinese risers. Always make sure you got a few spares, and don't insist on powering up a failing rig remotely if you suspect there's a hardware/power error.
Always use MOLEX powered cables to avoid fire 6 pin to SATA is fine too, right?
|
|
|
|
treanski
Full Member
Offline
Activity: 364
Merit: 106
ONe Social Network.
|
|
February 21, 2018, 06:24:57 PM |
|
As always, one of my rigs started to act up whilst I was on holiday. One GPU would start showing 511C errors, crash the miner and the rig within a few sec. Seeing that this couldn't be fixed remotely I cut the power to that rig completely using the tp-link smart plug app and decided to address it when I got back.
It was quite an easy diagnostic:
https://[Suspicious link removed]/p/ETFBZz
Flimsy Chinese risers. Always make sure you got a few spares, and don't insist on powering up a failing rig remotely if you suspect there's a hardware/power error.
Always use MOLEX powered cables to avoid fire 6 pin to SATA is fine too, right? no never use anything with fucking sata to power risers. in worst case you will destroy your gpu or burn your home
|
|
|
|
hous26
|
|
February 21, 2018, 06:29:50 PM |
|
As always, one of my rigs started to act up whilst I was on holiday. One GPU would start showing 511C errors, crash the miner and the rig within a few sec. Seeing that this couldn't be fixed remotely I cut the power to that rig completely using the tp-link smart plug app and decided to address it when I got back.
It was quite an easy diagnostic:
https://[Suspicious link removed]/p/ETFBZz
Flimsy Chinese risers. Always make sure you got a few spares, and don't insist on powering up a failing rig remotely if you suspect there's a hardware/power error.
Always use MOLEX powered cables to avoid fire 6 pin to SATA is fine too, right? no never use anything with fucking sata to power risers. in worst case you will destroy your gpu or burn your home I have never seen risers without SATA. I thought the problem was MOLEX to SATA. Can you show me the better risers?
|
|
|
|
Set Ready Go
Member
Offline
Activity: 273
Merit: 17
|
|
February 21, 2018, 06:59:57 PM |
|
As always, one of my rigs started to act up whilst I was on holiday. One GPU would start showing 511C errors, crash the miner and the rig within a few sec. Seeing that this couldn't be fixed remotely I cut the power to that rig completely using the tp-link smart plug app and decided to address it when I got back.
It was quite an easy diagnostic:
https://[Suspicious link removed]/p/ETFBZz
Flimsy Chinese risers. Always make sure you got a few spares, and don't insist on powering up a failing rig remotely if you suspect there's a hardware/power error.
Always use MOLEX powered cables to avoid fire 6 pin to SATA is fine too, right? no never use anything with fucking sata to power risers. in worst case you will destroy your gpu or burn your home I have never seen risers without SATA. I thought the problem was MOLEX to SATA. Can you show me the better risers? https://m.aliexpress.com/item/32819272286.html?pid=808_0000_0109&spm=a2g0n.search-amp.list.32819272286really solid risers, just use 6 pin pcie from your psu instead of the adapters.
|
|
|
|
hous26
|
|
February 21, 2018, 08:03:44 PM |
|
As always, one of my rigs started to act up whilst I was on holiday. One GPU would start showing 511C errors, crash the miner and the rig within a few sec. Seeing that this couldn't be fixed remotely I cut the power to that rig completely using the tp-link smart plug app and decided to address it when I got back.
It was quite an easy diagnostic:
https://[Suspicious link removed]/p/ETFBZz
Flimsy Chinese risers. Always make sure you got a few spares, and don't insist on powering up a failing rig remotely if you suspect there's a hardware/power error.
Always use MOLEX powered cables to avoid fire 6 pin to SATA is fine too, right? no never use anything with fucking sata to power risers. in worst case you will destroy your gpu or burn your home I have never seen risers without SATA. I thought the problem was MOLEX to SATA. Can you show me the better risers? https://m.aliexpress.com/item/32819272286.html?pid=808_0000_0109&spm=a2g0n.search-amp.list.32819272286really solid risers, just use 6 pin pcie from your psu instead of the adapters. Those are like mine but I use the 6 pin to SATA adapter and SATA cable that came with my EVGA PSU. You're saying I should use a 6 pin to 6 pin cable instead? Dumb question, but which port would be used to make this connection? PERF, SATA, VGA or CPU? If VGA then I wouldn't have the ports to do it anyways.
|
|
|
|
Swiftpain
Newbie
Offline
Activity: 9
Merit: 0
|
|
February 21, 2018, 08:24:25 PM |
|
As always, one of my rigs started to act up whilst I was on holiday. One GPU would start showing 511C errors, crash the miner and the rig within a few sec. Seeing that this couldn't be fixed remotely I cut the power to that rig completely using the tp-link smart plug app and decided to address it when I got back.
It was quite an easy diagnostic:
https://[Suspicious link removed]/p/ETFBZz
Flimsy Chinese risers. Always make sure you got a few spares, and don't insist on powering up a failing rig remotely if you suspect there's a hardware/power error.
Always use MOLEX powered cables to avoid fire 6 pin to SATA is fine too, right? no never use anything with fucking sata to power risers. in worst case you will destroy your gpu or burn your home RIP me, since my psu only has 2 pci ports and they are being used for cards. My risers have a 6 pin port, sata port, and a 4 pin port. I just used the 6 pin out of the back. I also use the 6 pin to sata since thats what came with the riser, so I guessed that is how it was meant to be used.
|
|
|
|
zorachus99
Jr. Member
Offline
Activity: 58
Merit: 3
|
|
February 21, 2018, 08:26:17 PM |
|
It's always the connector, from my experience. They tend to be cheap and dangerous.
I switched out all my adaptors/connectors and use straight PSU to the riser, have never had a problem since.
This is good advice. Thanks! My risers came with adapter cables for sata, and I was using them, and wondering if they would really be sufficient.
|
|
|
|
|