I Recently purchased 2 miners. One I got working just fine the other I am having a hard time getting it setup and running. I am not able to see the version name, I attached a picture showing the System/Overview tab depicting this error. Also my miner does not seem to fully boot I have attached the Kernal Script below up to where it stops - I have left the machine on for 30min and it still doesn't get past...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.14.0-xilinx-gb190cb0-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #57 SMP PREEMPT Fri Dec 9 14:49:22 CST 2016
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Xilinx Zynq
[ 0.000000] cma: CMA: reserved 128 MiB at 16800000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 126976
[ 0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map debd8000
[ 0.000000] Normal zone: 992 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 126976 pages, LIFO batch:31
[ 0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[ 0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 125984
[ 0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 364356K/507904K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 143548K reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xdf800000 - 0xff000000 ( 504 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdf000000 ( 496 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc06d1374 (6949 kB)
[ 0.000000] .init : 0xc06d2000 - 0xc0705380 ( 205 kB)
[ 0.000000] .data : 0xc0706000 - 0xc074cf78 ( 284 kB)
[ 0.000000] .bss : 0xc074cf84 - 0xc078d9fc ( 259 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] ps7-slcr mapped to df802000
[ 0.000000] zynq_clock_init: clkc starts at df802100
[ 0.000000] Zynq clock init
[ 0.000014] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[ 0.000311] ps7-ttc #0 at df804000, irq=43
[ 0.000620] Console: colour dummy device 80x30
[ 0.000653] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[ 0.040207] pid_max: default: 32768 minimum: 301
[ 0.040427] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.040447] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.042597] CPU: Testing write buffer coherency: ok
[ 0.042932] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.042992] Setting up static identity map for 0x4c4af8 - 0x4c4b50
[ 0.043216] L310 cache controller enabled
[ 0.043236] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[ 0.121034] CPU1: Booted secondary processor
[ 0.210228] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.210359] Brought up 2 CPUs
[ 0.210378] SMP: Total of 2 processors activated.
[ 0.210387] CPU: All CPU(s) started in SVC mode.
[ 0.211047] devtmpfs: initialized
[ 0.213478] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.214694] regulator-dummy: no parameters
[ 0.222366] NET: Registered protocol family 16
[ 0.224665] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.226958] cpuidle: using governor ladder
[ 0.226971] cpuidle: using governor menu
[ 0.234374] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[ 0.235885] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.235899] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.236012] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[ 0.257770] bio: create slab <bio-0> at 0
[ 0.259189] vgaarb: loaded
[ 0.259897] SCSI subsystem initialized
[ 0.260937] usbcore: registered new interface driver usbfs
[ 0.261748] usbcore: registered new interface driver hub
[ 0.262007] usbcore: registered new device driver usb
[ 0.262534] media: Linux media interface: v0.10
[ 0.262690] Linux video capture interface: v2.00
[ 0.262931] pps_core: LinuxPPS API ver. 1 registered
[ 0.262943] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.263067] PTP clock support registered
[ 0.263426] EDAC MC: Ver: 3.0.0
[ 0.264463] Advanced Linux Sound Architecture Driver Initialized.
[ 0.267283] DMA-API: preallocated 4096 debug entries
[ 0.267297] DMA-API: debugging enabled by kernel config
[ 0.267370] Switched to clocksource arm_global_timer
[ 0.287569] NET: Registered protocol family 2
[ 0.288237] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.288295] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.288380] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.288431] TCP: reno registered
[ 0.288449] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.288479] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.288723] NET: Registered protocol family 1
[ 0.289029] RPC: Registered named UNIX socket transport module.
[ 0.289041] RPC: Registered udp transport module.
[ 0.289049] RPC: Registered tcp transport module.
[ 0.289058] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.289072] PCI: CLS 0 bytes, default 64
[ 0.289503] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 0.291512] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.293636] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.293819] msgmni has been set to 967
[ 0.294608] io scheduler noop registered
[ 0.294621] io scheduler deadline registered
[ 0.294670] io scheduler cfq registered (default)
[ 0.305820] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[ 0.305840] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[ 0.429291] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[ 0.996711] console [ttyPS0] enabled
[ 1.000995] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[ 1.008633] [drm] Initialized drm 1.1.0 20060810
[ 1.025631] brd: module loaded
[ 1.035025] loop: module loaded
[ 1.044458] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[ 1.050544] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 1.058615] libphy: XEMACPS mii bus: probed
[ 1.062985] ------------- phy_id = 0x3625e62
[ 1.067893] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[ 1.076463] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.083111] ehci-pci: EHCI PCI platform driver
[ 1.090427] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[ 1.097226] usbcore: registered new interface driver usb-storage
[ 1.104104] mousedev: PS/2 mouse device common for all mice
[ 1.110245] i2c /dev entries driver
[ 1.117104] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[ 1.122618] cpufreq_cpu0: failed to get cpu0 regulator: -19
[ 1.128606] Xilinx Zynq CpuIdle Driver started
[ 1.133443] sdhci: Secure Digital Host Controller Interface driver
[ 1.139646] sdhci: Copyright(c) Pierre Ossman
[ 1.143916] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.150732] mmc0: no vqmmc regulator found
[ 1.154743] mmc0: no vmmc regulator found
[ 1.197393] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[ 1.206083] usbcore: registered new interface driver usbhid
[ 1.211586] usbhid: USB HID core driver
[ 1.216296] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 1.222593] nand: Micron MT29F2G08ABAEAWP
[ 1.226561] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[ 1.232498] Bad block table found at page 131008, version 0x01
[ 1.238722] Bad block table found at page 130944, version 0x01
[ 1.244776] 3 ofpart partitions found on MTD device pl353-nand
[ 1.250560] Creating 3 MTD partitions on "pl353-nand":
[ 1.255656] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[ 1.263703] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[ 1.271030] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[ 1.279956] TCP: cubic registered
[ 1.283191] NET: Registered protocol family 17
[ 1.287922] Registering SWP/SWPB emulation handler
[ 1.293799] regulator-dummy: disabling
[ 1.298124] UBI: attaching mtd1 to ubi0
[ 1.828918] UBI: scanning is finished
[ 1.840622] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[ 1.847703] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 1.854446] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 1.861148] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 1.868007] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[ 1.873975] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 1.881107] UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 916511165
[ 1.890051] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[ 1.899266] UBI: background thread "ubi_bgt0d" started, PID 1080
[ 1.899271] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.903196] ALSA device list:
[ 1.903199] No soundcards found.
[ 1.919649] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[ 1.972319] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[ 1.978291] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 1.987394] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[ 1.997256] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 2.002313] UBIFS: media format: w4/r0 (latest is w4/r0), UUID BBDF9B01-1A34-456B-9FBF-33B446951E64, small LPT model
[ 2.013613] VFS: Mounted root (ubifs filesystem) on device 0:11.
[ 2.020605] devtmpfs: mounted
[ 2.023709] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[ 2.863122] random: dd urandom read with 0 bits of entropy available
[ 3.257402]
[ 3.257402] bcm54xx_config_init
[ 3.867415]
[ 3.867415] bcm54xx_config_init
[ 7.868239] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[ 7.874346] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
[ 22.583907] In axi fpga driver!
[ 22.586973] request_mem_region OK!
[ 22.590403] AXI fpga dev virtual address is 0xdf9fc000
[ 22.595470] *base_vir_addr = 0x8c510
[ 22.610509] In fpga mem driver!
[ 22.613719] request_mem_region OK!
[ 22.617278] fpga mem virtual address is 0xe2000000
[ 23.417395]
[ 23.417395] bcm54xx_config_init
[ 24.047386]
[ 24.047386] bcm54xx_config_init
[ 28.048440] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[ 28.054547] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
This is XILINX board. Totalram: 507527168
Detect 512MB control board of XILINX
Find Force Freq=600 will search Freq again!
DETECT HW version=0008c510
miner ID : 81040d8162bb885c
config file found, will disable freq setting.
Miner Type = S9
AsicType = 1387
real AsicNum = 63
Find /tmp/searcherror: J7:2 The last log is below:
This is XILINX board. Totalram: 507527168
Detect 512MB control board of XILINX
Find Force Freq=600 will search Freq again!
DETECT HW version=0008c510
miner ID : 81040d8162bb885c
config file found, will disable freq setting.
Miner Type = S9
AsicType = 1387
real AsicNum = 63
use critical mode to search freq...
get PLUG ON=0x000000e0
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
set_reset_allhashboard = 0x0000ffff
Check chain[5] PIC fw version=0x03
Check chain[6] PIC fw version=0x03
Check chain[7] PIC fw version=0x03
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Start search freq on chain[5]...
Check chain[5] PIC fw version=0x03
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Start search freq on chain[6]...
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Start search freq on chain[7]...
Check chain[7] PIC fw version=0x03
get PIC voltage=125 on chain[5], value=870
get PIC voltage=125 on chain[6], value=870
get PIC voltage=125 on chain[7], value=870
set voltage=870 search freq on chain[5]
now set pic voltage=125 on chain[5]
set voltage=870 search freq on chain[6]
now set pic voltage=125 on chain[6]
set voltage=870 search freq on chain[7]
now set pic voltage=125 on chain[7]
enable_pic_dac on chain[5]
enable_pic_dac on chain[6]
enable_pic_dac on chain[7]
set_reset_allhashboard = 0x00000000
chain[5] temp offset record: 62,0,0,0,0,0,36,28
chain[5] temp chip I2C addr=0x98
chain[5] has no middle temp, use special fix mode.
chain[6] temp offset record: 62,0,0,0,0,0,35,28
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
chain[7] temp offset record: 62,0,0,0,0,0,35,28
chain[7] temp chip I2C addr=0x98
chain[7] has no middle temp, use special fix mode.
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
CRC error counter=0
set command mode to VIL
--- check asic number
check chain[5]: asicNum = 63
check chain[6]: asicNum = 0
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry check chain[6]: asicNum = 0
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry check chain[6]: asicNum = 0
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry check chain[6]: asicNum = 0
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry check chain[6]: asicNum = 0
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry check chain[6]: asicNum = 0
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry check chain[6]: asicNum = 0
The AsicNum=0 on chain[6]
