warhawk187
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 04, 2014, 09:07:47 PM |
|
My 12 (17 two weeks later) Antminers, 1 KNC Jupiter, and my slowly crapping out 8 stack of Bitburner Fury's (only one stack shown). Fall/winter 2013 til now have been great. My power bill however was not. NYC electricity is NOT cheap. ![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fi.imgur.com%2FYTwUCHP.jpg%3F2&t=665&c=2uunQ3U6l3MwrQ)
|
|
|
|
the-skeptic
Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 91
Merit: 10
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 04, 2014, 10:03:21 PM |
|
Two of my six Antminers. I've made custom covers for all of them, which helps force a lot more air over the heat sinks and chips. ![](https://ip.bitcointalk.org/?u=http%3A%2F%2Fwww.bostick-sullivan.com%2Fimages%2Fantminers.jpg&t=665&c=Gg2UR_FoMNQsQQ)
|
|
|
|
wpgdeez
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 04, 2014, 10:41:03 PM |
|
How much did your temps drop?
|
|
|
|
S4VV4S
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 04, 2014, 11:14:05 PM |
|
Two of my six Antminers. I've made custom covers for all of them, which helps force a lot more air over the heat sinks and chips. ![](https://ip.bitcointalk.org/?u=http%3A%2F%2Fwww.bostick-sullivan.com%2Fimages%2Fantminers.jpg&t=665&c=Gg2UR_FoMNQsQQ) My brother actually suggested that i should do the same about a week ago. He said it will work out much better to reduce heat that way. So, how is it going? EDIT: Doesn't the hot air coming out from one Ant affect the heat of the other? I mean because you have them facing the opposite direction.
|
|
|
|
the-skeptic
Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 91
Merit: 10
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 05, 2014, 12:27:01 AM |
|
Two of my six Antminers. I've made custom covers for all of them, which helps force a lot more air over the heat sinks and chips.
My brother actually suggested that i should do the same about a week ago. He said it will work out much better to reduce heat that way. So, how is it going? EDIT: Doesn't the hot air coming out from one Ant affect the heat of the other? I mean because you have them facing the opposite direction. I usually have them facing the same direction, I just turned one around to take the picture. I have a IR temp gun and found that without the cover, the chips closest to the fans get up to about 103^F and the chips furthest away get up to 135^F. With the covers on, the chips all seem to settle around 118-122^F. Without the cover the heatsink end gets up to 120-123^F, but the cover brings the heatsink down to 115-118^F. If people are interested in covers, I am considering making them for sale. I think they would sell for around BTC .018 - .020 depending on exchange. Powder coated .025" aluminum, would include a bottom plate, back cover with cable pass-thru and top cover.
|
|
|
|
S4VV4S
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 05, 2014, 12:39:15 AM |
|
Two of my six Antminers. I've made custom covers for all of them, which helps force a lot more air over the heat sinks and chips.
My brother actually suggested that i should do the same about a week ago. He said it will work out much better to reduce heat that way. So, how is it going? EDIT: Doesn't the hot air coming out from one Ant affect the heat of the other? I mean because you have them facing the opposite direction. I usually have them facing the same direction, I just turned one around to take the picture. I have a IR temp gun and found that without the cover, the chips closest to the fans get up to about 103^F and the chips furthest away get up to 135^F. With the covers on, the chips all seem to settle around 118-122^F. Without the cover the heatsink end gets up to 120-123^F, but the cover brings the heatsink down to 115-118^F. If people are interested in covers, I am considering making them for sale. I think they would sell for around BTC .018 - .020 depending on exchange. Powder coated .025" aluminum, would include a bottom plate, back cover with cable pass-thru and top cover. I think you should but you should do it now. Summer is just around the corner, and when something can help bring the heat down.... Have you considered starting up a group buy and see how that goes? EDIT: I can start one for you if you want ![Grin](https://bitcointalk.org/Smileys/default/grin.gif)
|
|
|
|
freebit13
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 05, 2014, 08:51:20 AM |
|
When covering my ants I found that it increased the fan speed and it got a little louder ![Undecided](https://bitcointalk.org/Smileys/default/undecided.gif)
|
Decentralize EVERYTHING!
|
|
|
salfter
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 06, 2014, 03:18:51 AM |
|
![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fi.imgur.com%2FJEaFDBGl.jpg&t=665&c=FEhTMXkV3F4rFQ) This is just part of my mining setup...some Bitfury and BFL gear is off-frame to the left. Each Antminer gets its own power supply. Both are modular; the first one (on the right) has a 600W Corsair, while the second one (on the left) has a 550W Seasonic. The Corsair puts both of its PCIe outputs on a single cable, which gets a little warmer than I'd like; the Seasonic uses a cable for each and is a better (if more expensive) choice. They're on a wire rack in the laundry room. Connection is through an 8-port switch connected to the LAN through an 85-Mbps (yeah, right!) powerline-networking adapter. I could possibly clean things up by switching to WiFi: add antennas to the Antminers and a WiFi USB dongle to the Raspberry Pi in the Bitfury rig. Ventilation is pretty decent; you barely feel some warm air coming from the power supplies, but all of the miners keep the room toasty. The Kill-a-Watt (not shown, but it's below the picture) says everything's pulling about 1.08 kW.
|
|
|
|
miaviator
Donator
Hero Member
Offline
Activity: 686
Merit: 519
It's for the children!
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 06, 2014, 04:33:36 PM |
|
I keep all of mine in 4U rack mount cases so not much to look at from the front. Here is the back of a leased pair: ![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fi.imgur.com%2FTCpdpnD.jpg%3F1&t=665&c=GgqAAm4ZCOzCvg)
|
|
|
|
s1lverbox (OP)
Legendary
Offline
Activity: 2324
Merit: 1039
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 06, 2014, 06:59:42 PM |
|
I keep all of mine in 4U rack mount cases so not much to look at from the front. Here is the back of a leased pair: ![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fi.imgur.com%2FTCpdpnD.jpg%3F1&t=665&c=GgqAAm4ZCOzCvg) So your psu sucking heat from side of miner?
|
|
|
|
miaviator
Donator
Hero Member
Offline
Activity: 686
Merit: 519
It's for the children!
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 06, 2014, 07:05:20 PM |
|
So your psu sucking heat from side of miner? Yes, I had thought of isolating everything and sticking three ANT's per chassis. This setup takes a whole 5 minutes and the miners run at 43-44F so I figured I would leave it alone. If I need more space I can always stack 3 and vent the PSU above the miners.
|
|
|
|
NetTime
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 06, 2014, 09:11:17 PM |
|
Buck Rogers and Street Fighter 2, nice.
|
|
|
|
|
Pcpoet
Full Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif) ![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 156
Merit: 100
Cryptocurrency Rules man!
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 06, 2014, 09:32:31 PM |
|
Are there any pc cases that would fit 2 antminer s1 in it? I wanted to know because my Local Datacenter requires it in a enclosure. If any body have any good ideas let me know thanks!
|
“Yabba Dabba Doo!!”- Fred Flintstone
|
|
|
|
clarkey2013
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 07, 2014, 02:51:05 AM |
|
what are you guys that living in the UK paying for import duties on a single Antminer?
|
|
|
|
Pcpoet
Full Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif) ![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 156
Merit: 100
Cryptocurrency Rules man!
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 07, 2014, 03:25:08 AM |
|
The Cabinet is a G2 HP 42U Cabinet. What kind of Rails do you recommend for this case? I totally appreciate it, you are a great person! ![Smiley](https://bitcointalk.org/Smileys/default/smiley.gif)
|
“Yabba Dabba Doo!!”- Fred Flintstone
|
|
|
miaviator
Donator
Hero Member
Offline
Activity: 686
Merit: 519
It's for the children!
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 07, 2014, 04:47:25 AM |
|
The Cabinet is a G2 HP 42U Cabinet. What kind of Rails do you recommend for this case? I totally appreciate it, you are a great person! ![Smiley](https://bitcointalk.org/Smileys/default/smiley.gif) I'm lazy, I usually just screw them into the rack from the front panel. The rails for these cases are about $20 a shot from newegg.
|
|
|
|
elpenguin
Newbie
Offline
Activity: 52
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 07, 2014, 09:45:21 AM |
|
what are you guys that living in the UK paying for import duties on a single Antminer?
About £110 on my last order at the end of Feb.
|
|
|
|
death_hawk
Newbie
Offline
Activity: 22
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 07, 2014, 11:26:16 AM |
|
|
|
|
|
|