The Blackminer F1 is a new FPGA miner. According to the officially released parameters, more than 10 different algorithms of altcoins have been programmed into it, and the specs are staggering. Designed with brand new technology and boasting very high hash rates, the F1 is the most powerful and efficient FPGA altcoin miner to date.
Here is our review of Blackminer F1.
Blackminer F1 basic parametersMiner Algo Hashrate
Lyra2z 32.00MH/s
Skein 5.04GH/s
Lyra2rev2 216.00MH/s
phi2 LUX 51.70MH/s
phi1612 314.00MH/s
tribus 2.94GH/s
nexus 2.76GH/s
xdag 14.40GH/s
bcx 16.56GH/s
keccak/keccakc 21.12GH/s
Bismuth BIS 19.32GH/s
* The algorithm Lyra2z in the above table is expected to increase significantly within 2 week by 2 to 3 times.
* The algorithm phi2 and yra2rev2 are expected to increase significantly in the near future.
The Blackminer F1 is designed with a single front fan and two hash boards. The outer hull is molded in one piece and is made of precision die-cast design and aluminum alloy. This design not only provides strong protection for the hash boards, but also enhances the heat dissipation performance of mining machine.
As can be seen from the top of the mining machine, the Blackminer F1 consists of two hash boards. Each of the hash board has two 6pin ports while control boards has one. Each interface needs to be connected to a power supply. Two sets of wires connect the controller and the two hash boards.
On the front of the controller, we can see the IP address feedback button, Ethernet cable interface, reset button and status indicators. The front fan of the mining machine is the air inlet area. The rear fan has not been adopted but a spider web shaped plate is very good for air flow, which makes the overall design lighter and smoother. The internal structure of the Blackminer F1 is very concise and it provides a larger heat dissipation area. The module spacing also forms a unique air duct inside the mining machine, which is maximizing the use of fans and structural walls to maximize heat dissipation.
Blackminer F1 installation and reviewThe installation of the Blackminer F1 is very simple. We use an ATX power supply, plug the connectors of the PSU into the two hash boards and controller, plug in the Ethernet cable into the Ethernet adapter port. The default IP address of Blackminer F1 is 192.168.50.224. Open the browser and use this IP address to enter the background of the mining machine.
We can see through the background that there are five default algorithms in Blackminer F1: bitmuth, lyra2z, skeincoin, xdag and xvg_lyra2rev2. Every user can switch the algorithms by mining only with one button. It takes about a time for a computer to restart, then the miner can immediately mining the digital currency with this algorithm, which is very easy to operate.
According to the official specs of Blackminer F1, the hash rates and power consumption of different algorithms of F1 are different. In this review, we choose the bismuth algorithm. During the observation period, the hash rate is stable at 20.3-20.8 Gh/s. The frequency is set at 460 M, and the actual power consumption is about 618 W. As can be seen from the background, the temperature of the chips is 60-63℃.
The official website will update the corresponding firmware in order to better serve Blackminer users. It is simple to configure which users only need to download and update.
Cloud miningCloud mining services are also provided to all users who do not have proper mining sites. Users can get the mining profits immediately after purchasing the mining machine. All Blackminers are hosted in Blackminer official mining farm. And you can get the most professional maintenance and technical support without bearing the cost of transportation and noise.
More details about cloud mining here:
https://hashaltcoin.com
Summary of Blackminer F1The appearance of the Blackminer F1 is somewhat similar to that of the Antminer. However, as an FPGA miner, its performance is very impressive. It delivers very good hash rates but with low power consumption. It also performs well in terms of temperature and noise level.
So, the conclusions of this review:
1. The design structure is compact and reasonable.
2. It is simple to set up.
3. The running and operation is stable.
4. It is suitable for many mining scenes.
5. Cloud mining is a option.
We will update the continued performance of this Blackminer F1.
Contact:
Official Website:
https://hashaltcoin.comOfficial Support:
support@hashaltcoin.comOfficial Discord:
https://discord.gg/eUNRSgyYoutube:
https://youtu.be/_4bxmtEAock
