alex1560 (OP)
Member
Offline
Activity: 67
Merit: 24
|
|
November 21, 2018, 09:23:07 AM Last edit: November 21, 2018, 09:28:18 PM by frodocooper |
|
Ya, it's actually the LPM which doesn't like overclocking on some boards, especially the 13.5 machines or older 14TH.
I plan on putting some more work into finding a solution for this in the following weeks, until then, the best solution for LPM is the original firmware on bitmain without overclock.
There are some users which were lucky and it worked, so always test on a few machines before mass deployment.
|
|
|
|
behnam98
Newbie
Offline
Activity: 2
Merit: 0
|
|
November 25, 2018, 10:30:04 AM |
|
how to work "Customize the fan speed percentage" item ? i have t9+ , but my fan speed not change by change this item !! i test 10 , 20 , .... , 150 and more for this field
|
|
|
|
alex1560 (OP)
Member
Offline
Activity: 67
Merit: 24
|
|
November 26, 2018, 07:15:12 PM |
|
how to work "Customize the fan speed percentage" item ? i have t9+ , but my fan speed not change by change this item !! i test 10 , 20 , .... , 150 and more for this field Hi, I have not tested that feature on T9+ unfortunately. Might be different because of the controller.
|
|
|
|
boogiebl
Newbie
Offline
Activity: 3
Merit: 0
|
|
December 09, 2018, 06:14:49 PM |
|
Hi,
I did backup config before deploy on "upgrade" page.
if I now restore my backup on the same page, will everything be as before deploy?
|
|
|
|
fanatic26_
|
|
December 10, 2018, 11:59:23 PM |
|
Hi,
I did backup config before deploy on "upgrade" page.
if I now restore my backup on the same page, will everything be as before deploy?
No. That just backed up the user settings, pools and such. It did not create a backup of your firmware.
|
|
|
|
boogiebl
Newbie
Offline
Activity: 3
Merit: 0
|
|
December 15, 2018, 10:46:58 AM Last edit: December 18, 2018, 11:22:41 PM by frodocooper |
|
:/ ok. And how can I get back to the state before? Can I install new firmware? I want to have the option to return to the factory settings in case something goes wrong. I have 4 more devices and I would also set them up
again i ... can anyone tell me how to backup the BBMINER? so I can restore the default. I asked for a google but did not find it. now the temperature is great for OC but in the spring I will probably have to reduce the frequency and voltage .... for now i deploy one device and i have 4 more ... so i do not spoil something .... P.S. and what is the default voltage? the frequency is from 568 MHz to 575 MHz ...
|
|
|
|
alex1560 (OP)
Member
Offline
Activity: 67
Merit: 24
|
|
December 17, 2018, 11:52:43 PM Last edit: December 17, 2018, 11:58:04 PM by frodocooper |
|
|
|
|
|
boogiebl
Newbie
Offline
Activity: 3
Merit: 0
|
|
December 18, 2018, 04:12:45 PM Last edit: December 18, 2018, 11:23:28 PM by frodocooper |
|
one more question, and I will not be bored ... I have a DOA device ... can I deploy it https://imgur.com/a/Om2Y3v6
|
|
|
|
awilliams315
Newbie
Offline
Activity: 1
Merit: 0
|
|
January 14, 2019, 08:44:36 AM |
|
*** Some info for those with T9+ based off my machine ****
I have a T9+ and using 870 mV, 675 freq, have customize fan speed at 50%, and i left the box checked for going over 90 degrees since this is the first time i have used any software before with the miner.
With this I am averaging 12,511.71 GH/s and the temps are ranging from 80-86 on different chains. But my fan is constantly running at 6,120 so I gotta figure out that since I dont want it running full speed. But hope this helps someone
|
|
|
|
elmejorrematador
Member
Offline
Activity: 134
Merit: 21
|
|
July 16, 2019, 10:13:26 AM |
|
Hello guys,
So is the free version still available? I saw that there is supposed to be a for sale version to use for more than 10 machines?
|
|
|
|
taserz
Sr. Member
Offline
Activity: 800
Merit: 294
Created AutoTune to saved the planet! ~USA
|
|
November 29, 2019, 11:18:56 AM |
|
Hey I realized you edited out the front page. Is there a link anywhere for this as I would love to link this for the older bmminer mods on my other thread.
|
|
|
|
|