Zilminer - mine POW coin in dual mine mode with almost no power use!!!!!

[reb0rn21]

Coin and concept is at infancy, I had no issue at all with dual miner, but I guess it depend on system and with which primary miner is used

Everyone who do not mine grin (on windows) or have ~2+ GB of ram free on GPU can run this miner as same time with no need for start/kill bat files and zero issue to primary miner hash

With GPU-z under sensor tab you can see Memory used from total ram (4,6,8,11GB)
win 7 you need to have 1.3gb free to not use --clear-dag and start-stop
windows 10 you need to  have room for 2GB

Also due the number of miners and low reward, its profitable mostly for full rigs mining and not so match for one card alone

Also network is very slow in last 12h, one pow in 5-6h

[Grim]

which amd driver is recommended?

19.x.x doesn't seem to work?!

[Novator]

My address went though but you rejected our nodes.

[reb0rn21]

I have my own nodes, if nodes are accepted they will have to pay upfront in future, how I don`t have idea now, maybe when transaction start and we see where we stand

[Novator]

But can you accept for the meantime.

[sommersut]

I am almost giving up. Just one accepted share per day

[reb0rn21]

I am almost giving up. Just one accepted share per day

What hash rate you have?

Its not something to be mined with 1-2 GPU, as network is 17Gh, so one 150Mhs rig would have 2-5 shares per day (depending on luck) and network speed, yesterday we had just two POW work as chain was slow, so even if you had full rig you would need 100% luck to get 1 share

The calculation is done network diff/60sec so 17 000/60sec

Today network is faster but still not recovered 100%, as we need to have 8 POW per day, each 3h when all is right

Atm A/R rate is around +90% I think we can not go higher as there is lots of task to be done to be accepted by node as space is limited just to one shard or 600 nodes atm, and be sure more ppl mine then 600

[sommersut]

It makes sense now. Yes, I have only 120 MH/s so we are in agreement about the number of accepted shares.

[reb0rn21]

Yes and diff is now 34Gh maybe it drop down soon, don`t know

again 17Gh

[Novator]

Can you approve my node..

[reb0rn21]

pls read, I don`t accept nodes atm, if that change I will say it here and on the pool

[sxemini]

We need new command - POW end earlier. Because i loose to much time after zil mining. It needs about 3 minutes to get the pow end command. So every Zil pow it mines around 2minutes and the pow phase is around 6 - 8 minutes.

[reb0rn21]

You have
--pow-end-timeout 100

which start primary miner after 100sec timeout
also i think there are other commands for it but did not test

[reb0rn21]

Network nodes have been updated to latest, lets hope all go nice this time

next POW will be no work, after that POW should be normal

[bdmi9]

without node can be mine zil on windows 10 ?

i had tried but no luck on share .

if anybody can assist with it ?

br,
bdmi9

[reb0rn21]

You have my miner pack just edit bat, it works out of box with bminer

[sxemini]

You have
--pow-end-timeout 100

which start primary miner after 100sec timeout
also i think there are other commands for it but did not test

thanks this what i looking for.

[Grim]

You have
--pow-end-timeout 100

which start primary miner after 100sec timeout
also i think there are other commands for it but did not test

thanks this what i looking for.

but pow is only 30secs ?!

so what should it really be set to:

--pow-end-timeout 30  ?

[reb0rn21]

I don`t know, its set to be safe, also POW is atm a bit longer, coins devs are tweaking it on chain

[reb0rn21]

Bootstrap period is extended to end of march, more info from coin devs

https://www.reddit.com/r/zilliqa/comments/avv2ex/bootstrap_extended_up_to_end_of_march/