Antminer s9 hashboard lights go off after one minute 0GH

[mountrover]

Following an upgrade of firmware the hashboards on my s9 light up when the unit is restarted but after a minute the go off and there is no hashing going on.

Already tried.

Reboot = no change
Restore = Cannot Find Signature!!!
Upgrading using all the available updates on Bitmain's website
Reset
installing Bitmain fix firmware

I do have one dead hashboard in the unit, it never worked, but the other two worked, but now only light up for a minute, just as the fans kick in.

Any help appreciated.

[BitMaxz]

Do you have kernel logs? Can you copy it and paste it here so that we can review if what is the problem why you get this issue.

You can find the kernel logs from system>kernel logs then copy them all and paste it here http://pastebin.com/ put the link here

or use this code below and put your logs inside the codes

[mountrover]

Thank you for your reply,

here is the kernel log.

Code:

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.0-xilinx-g16220c3 (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #83 SMP PREEMPT Thu Jul 12 11:42:53 CST 2018
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Xilinx Zynq
[    0.000000] cma: CMA: reserved 128 MiB at 27800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 258048
[    0.000000] free_area_init_node: node 0, pgdat c074ac00, node_mem_map e6fd8000
[    0.000000]   Normal zone: 1520 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 194560 pages, LIFO batch:31
[    0.000000]   HighMem zone: 496 pages used for memmap
[    0.000000]   HighMem zone: 63488 pages, LIFO batch:15
[    0.000000] PERCPU: Embedded 8 pages/cpu @e6fc0000 s9088 r8192 d15488 u32768
[    0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 256528
[    0.000000] Kernel command line: noinitrd mem=1008M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 884108K/1032192K available (5057K kernel code, 284K rwdata, 1928K rodata, 204K init, 258K bss, 148084K reserved, 253952K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06da8ac   (6987 kB)
[    0.000000]       .init : 0xc06db000 - 0xc070e380   ( 205 kB)
[    0.000000]       .data : 0xc0710000 - 0xc0757138   ( 285 kB)
[    0.000000]        .bss : 0xc0757144 - 0xc0797bfc   ( 259 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] ps7-slcr mapped to f0004000
[    0.000000] zynq_clock_init: clkc starts at f0004100
[    0.000000] Zynq clock init
[    0.000014] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[    0.000293] ps7-ttc #0 at f0006000, irq=43
[    0.000595] Console: colour dummy device 80x30
[    0.000631] Calibrating delay loop... 1332.01 BogoMIPS (lpj=6660096)
[    0.090243] pid_max: default: 32768 minimum: 301
[    0.090452] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.090474] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.092628] CPU: Testing write buffer coherency: ok
[    0.092947] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.093005] Setting up static identity map for 0x4cb118 - 0x4cb170
[    0.093226] L310 cache controller enabled
[    0.093246] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[    0.170987] CPU1: Booted secondary processor
[    0.260221] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.260349] Brought up 2 CPUs
[    0.260367] SMP: Total of 2 processors activated.
[    0.260375] CPU: All CPU(s) started in SVC mode.
[    0.261032] devtmpfs: initialized
[    0.263451] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.264631] regulator-dummy: no parameters
[    0.271985] NET: Registered protocol family 16
[    0.274150] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.276407] cpuidle: using governor ladder
[    0.276420] cpuidle: using governor menu
[    0.283749] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[    0.285254] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.285267] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.285378] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xf0080000
[    0.307081] bio: create slab <bio-0> at 0
[    0.308461] vgaarb: loaded
[    0.309150] SCSI subsystem initialized
[    0.310011] usbcore: registered new interface driver usbfs
[    0.310334] usbcore: registered new interface driver hub
[    0.310746] usbcore: registered new device driver usb
[    0.312076] media: Linux media interface: v0.10
[    0.312243] Linux video capture interface: v2.00
[    0.312489] pps_core: LinuxPPS API ver. 1 registered
[    0.312501] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.312623] PTP clock support registered
[    0.312976] EDAC MC: Ver: 3.0.0
[    0.314177] Advanced Linux Sound Architecture Driver Initialized.
[    0.316879] DMA-API: preallocated 4096 debug entries
[    0.316892] DMA-API: debugging enabled by kernel config
[    0.316959] Switched to clocksource arm_global_timer
[    0.336398] NET: Registered protocol family 2
[    0.337095] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.337190] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.337349] TCP: Hash tables configured (established 8192 bind 8192)
[    0.337408] TCP: reno registered
[    0.337425] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.337475] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.337739] NET: Registered protocol family 1
[    0.338081] RPC: Registered named UNIX socket transport module.
[    0.338093] RPC: Registered udp transport module.
[    0.338101] RPC: Registered tcp transport module.
[    0.338110] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.338122] PCI: CLS 0 bytes, default 64
[    0.338544] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.340542] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.341891] bounce pool size: 64 pages
[    0.342746] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.342960] msgmni has been set to 1486
[    0.343740] io scheduler noop registered
[    0.343754] io scheduler deadline registered
[    0.343795] io scheduler cfq registered (default)
[    0.350993] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[    0.351013] dma-pl330 f8003000.ps7-dma: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[    0.473828] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[    1.045796] console [ttyPS0] enabled
[    1.050054] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to f0068000
[    1.057689] [drm] Initialized drm 1.1.0 20060810
[    1.074629] brd: module loaded
[    1.084029] loop: module loaded
[    1.093381] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.099200] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.106941] libphy: XEMACPS mii bus: probed
[    1.111339] ------------- phy_id = 0x3625e62
[    1.116045] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[    1.124724] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.131518] ehci-pci: EHCI PCI platform driver
[    1.138750] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[    1.145549] usbcore: registered new interface driver usb-storage
[    1.152417] mousedev: PS/2 mouse device common for all mice
[    1.158569] i2c /dev entries driver
[    1.165443] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[    1.170967] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    1.176848] Xilinx Zynq CpuIdle Driver started
[    1.181743] sdhci: Secure Digital Host Controller Interface driver
[    1.187862] sdhci: Copyright(c) Pierre Ossman
[    1.192176] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.199045] mmc0: no vqmmc regulator found
[    1.203056] mmc0: no vmmc regulator found
[    1.247001] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[    1.255678] usbcore: registered new interface driver usbhid
[    1.261190] usbhid: USB HID core driver
[    1.265898] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.272189] nand: Micron MT29F2G08ABAEAWP
[    1.276159] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    1.282112] Bad block table found at page 131008, version 0x01
[    1.288340] Bad block table found at page 130944, version 0x01
[    1.294395] 3 ofpart partitions found on MTD device pl353-nand
[    1.300161] Creating 3 MTD partitions on "pl353-nand":
[    1.305270] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[    1.313302] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[    1.320617] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[    1.331327] TCP: cubic registered
[    1.334558] NET: Registered protocol family 17
[    1.339290] Registering SWP/SWPB emulation handler
[    1.345206] regulator-dummy: disabling
[    1.349535] UBI: attaching mtd1 to ubi0
[    1.872791] UBI: scanning is finished
[    1.884344] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[    1.891423] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.898186] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.904850] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.911728] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[    1.917708] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    1.924816] UBI: max/mean erase counter: 6/3, WL threshold: 4096, image sequence number: 1885751282
[    1.933858] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[    1.943074] UBI: background thread "ubi_bgt0d" started, PID 1084
[    1.943080] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.947015] ALSA device list:
[    1.947019]   No soundcards found.
[    1.963359] UBIFS: background thread "ubifs_bgt0_0" started, PID 1086
[    1.992314] UBIFS: recovery needed
[    2.113801] UBIFS: recovery completed
[    2.117492] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    2.123420] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    2.132553] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    2.142444] UBIFS: reserved for root: 0 bytes (0 KiB)
[    2.147479] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 169D5274-BC1D-448D-AF98-689AB312947D, small LPT model
[    2.158760] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    2.165913] devtmpfs: mounted
[    2.169040] Freeing unused kernel memory: 204K (c06db000 - c070e000)
[    3.001943] random: dd urandom read with 1 bits of entropy available
[    3.387007] 
[    3.387007] bcm54xx_config_init
[    3.996999] 
[    3.996999] bcm54xx_config_init
[    7.997825] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[    8.003930] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
[   25.829222] In axi fpga driver!
[   25.832294] request_mem_region OK!
[   25.835689] AXI fpga dev virtual address is 0xf0200000
[   25.840823] *base_vir_addr = 0xc51e
[   25.855452] In fpga mem driver!
[   25.858870] request_mem_region OK!
[   25.862381] fpga mem virtual address is 0xf3000000
[   26.666974] 
[   26.666974] bcm54xx_config_init
[   27.297009] 
[   27.297009] bcm54xx_config_init
[   31.297831] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[   31.303938] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
[  704.919396] random: nonblocking pool is initialized
log_level = 4
This is XILINX board. Totalram:       1039753216
Detect 1GB control board of XILINX
mmap axi_fpga_addr = 0xb6ffb000
axi_fpga_addr data = 0xc51e
mmap fpga_mem_addr = 0xb5df4000
forceFreq=-1 forceFlag=0
min work minertest[0]:912


DETECT HW version=0000c51e
miner ID : 81204c411375885c
Miner Type = S9
AsicType = 1387
real AsicNum = 63
use critical mode to search freq...
get PLUG ON=0x000000e0
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
Check chain[5] PIC fw version=0x03
Check chain[6] PIC fw version=0x03
Check chain[7] PIC fw version=0x03
read pic freq and badcore num...
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[5] has freq in PIC and will jump over...
Chain[5] has core num in PIC
Chain[5] ASIC[13] has core num=1
Chain[5] ASIC[29] has core num=1
Check chain[5] PIC fw version=0x03
read pic freq and badcore num...
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[6] has freq in PIC and will jump over...
Chain[6] has core num in PIC
Chain[6] ASIC[25] has core num=1
Chain[6] ASIC[44] has core num=2
Chain[6] ASIC[46] has core num=15
Check chain[6] PIC fw version=0x03
read pic freq and badcore num...
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[7] has freq in PIC and will jump over...
Chain[7] has core num in PIC
Chain[7] ASIC[10] has core num=1
Chain[7] ASIC[14] has core num=2
Chain[7] ASIC[26] has core num=7
Chain[7] ASIC[45] has core num=6
Chain[7] ASIC[46] has core num=15
Chain[7] ASIC[47] has core num=3
Chain[7] ASIC[50] has core num=6
Chain[7] ASIC[57] has core num=3
Check chain[7] PIC fw version=0x03
get PIC voltage=6 on chain[5], value=940
get PIC voltage=6 on chain[6], value=940
get PIC voltage=6 on chain[7], value=940
chain[5] temp offset record: 62,0,0,0,0,0,35,28
chain[5] temp chip I2C addr=0x98
chain[5] has no middle temp, use special fix mode.
chain[6] temp offset record: 62,0,0,0,0,0,35,28
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
chain[7] temp offset record: 62,0,0,0,0,0,35,28
chain[7] temp chip I2C addr=0x98
chain[7] has no middle temp, use special fix mode.
total_exist_chain_num = 3
CRC error counter=0
set command mode to VIL

--- check asic number
After Get ASIC NUM CRC error counter=0
set_baud=0
The min freq=700
set real timeout 52, need sleep=379392
After TEST CRC error counter=0
search freq for 1 times, completed chain = 3, total chain num = 3 
single_board_frq_tuning enter
min_rate, des_rate, fix_volt:13800, 14000, 880
force_freq not set, don't need tuning
restart Miner chance num=2
waiting for receive_func to exit!
waiting for pic heart to exit!
bmminer not found= 1374 root       0:00 grep bmminer

bmminer not found, restart bmminer ...
This is user mode for mining
Detect 1GB control board of XILINX
Miner Type = S9
Miner compile time: Mon Mar 4 11:37:08 CST 2019 type: Antminer S9set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
miner ID : 81204c411375885c
set_reset_allhashboard = 0x0000ffff
Checking fans!get fan[4] speed=6000
get fan[5] speed=11160
get fan[4] speed=6000
get fan[5] speed=11160
get fan[4] speed=6000
get fan[5] speed=11160
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
origin: 0 : 125 : 0 : 72 : 0 : 72 : 4
update: 0 : 125 : 0 : 27 : 0 : 27 : 4 
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=3 : 0
Chain[J6] has backup chain_voltage=830
Check chain[5] PIC fw version=0x03
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
origin: 0 : 125 : 0 : 77 : 0 : 77 : 4
update: 0 : 125 : 0 : 32 : 0 : 32 : 4 
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=3 : 0
Chain[J7] has backup chain_voltage=830
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
origin: 0 : 125 : 0 : 77 : 0 : 77 : 4
update: 0 : 125 : 0 : 32 : 0 : 32 : 4 
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=3 : 0
Chain[J8] has backup chain_voltage=830
Check chain[7] PIC fw version=0x03
Chain[J6] orignal chain_voltage_pic=6 value=940
Chain[J6] will use backup chain_voltage_pic=830 [193]
Chain[J6] get working chain_voltage_pic=193
Chain[J7] orignal chain_voltage_pic=6 value=940
Chain[J7] will use backup chain_voltage_pic=830 [193]
Chain[J7] get working chain_voltage_pic=193
Chain[J8] orignal chain_voltage_pic=6 value=940
Chain[J8] will use backup chain_voltage_pic=830 [193]
Chain[J8] get working chain_voltage_pic=193
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
Chain[J6] has 0 asic
set_reset_hashboard = 0x00000020
set_reset_hashboard = 0x00000000
retry Chain[J6] has 0 asic
set_reset_hashboard = 0x00000020
set_reset_hashboard = 0x00000000
retry Chain[J6] has 0 asic
set_reset_hashboard = 0x00000020
set_reset_hashboard = 0x00000000
retry Chain[J6] has 0 asic
set_reset_hashboard = 0x00000020
set_reset_hashboard = 0x00000000
retry Chain[J6] has 0 asic
set_reset_hashboard = 0x00000020
set_reset_hashboard = 0x00000000
retry Chain[J6] has 0 asic
set_reset_hashboard = 0x00000020
set_reset_hashboard = 0x00000000
retry Chain[J6] has 0 asic
Chain[J7] has 0 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 0 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 0 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 0 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 0 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 0 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 0 asic
Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 0 asic
miner total rate=0GH/s fixed rate=0GH/s

Miner fix freq ...
max freq = 100
set baud=1
setStartTimePoint total_tv_start_sys=200 total_tv_end_sys=201
restartNum = 2 , auto-reinit enabled...
do read_temp_func once...
do check_asic_reg 0x08
Done check_asic_reg
set FAN speed according to: temp_highest=0 temp_top1[PWM_T]=0 temp_top1[TEMP_POS_LOCAL]=0 temp_change=0 fix_fan_steps=0
set full FAN speed...
FAN PWM: 100
read_temp_func Done!
CRC error counter=1

[BitMaxz]

You are getting weird fan speed which reaches to 11160 RPM I don't know if it's a front fan(intake) or the exhaust fan

Code:

get fan[5] speed=11160
get fan[4] speed=6000
get fan[5] speed=11160
get fan[4] speed=6000
get fan[5] speed=11160

The normal fan speed in the front should be around 6000 rpm and for rear fan should be 4300 rpm so maybe your exhaust fan is defective

You also got 0 ASIC number to all of your hashboard with no temp.

Code:

Chain[J6] has 0 asic
set_reset_hashboard = 0x00000020
set_reset_hashboard = 0x00000000
retry Chain[J6] has 0 asic
set_reset_hashboard = 0x00000020
set_reset_hashboard = 0x00000000
retry Chain[J6] has 0 asic
set_reset_hashboard = 0x00000020
set_reset_hashboard = 0x00000000
retry Chain[J6] has 0 asic
set_reset_hashboard = 0x00000020
set_reset_hashboard = 0x00000000
retry Chain[J6] has 0 asic
set_reset_hashboard = 0x00000020
set_reset_hashboard = 0x00000000
retry Chain[J6] has 0 asic
set_reset_hashboard = 0x00000020
set_reset_hashboard = 0x00000000
retry Chain[J6] has 0 asic
Chain[J7] has 0 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 0 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 0 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 0 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 0 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 0 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 0 asic
Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 0 asic
miner total rate=0GH/s fixed rate=0GH/s

Miner fix freq ...
max freq = 100
set baud=1
setStartTimePoint total_tv_start_sys=200 total_tv_end_sys=201
restartNum = 2 , auto-reinit enabled...
do read_temp_func once...
do check_asic_reg 0x08
Done check_asic_reg
set FAN speed according to: temp_highest=0 temp_top1[PWM_T]=0 temp_top1[TEMP_POS_LOCAL]=0 temp_change=0 fix_fan_steps=0

Do you have extra PSU and Antminer s9?
Try to replace the 18 pins ribbon cable and PSU also try to replace the exhaust fan from a working s9 miner then test it again.

You can also check this possible problems and solutions for S9

Also, check this guide below for troubleshooting hashboard one by one
https://support.bitmain.com/hc/en-us/articles/226142788-Test-hash-board-one-by-one

[mountrover]

Thanks for your detailed response!

I will need to break this down a bit, my "mining operation" currently only extends to a single machine, so no easy way of swapping bits.

Should I start with new fans? or a new power supply?

The hashboards could be dead? or would they automatically be stopped from working because of fan issue?

[BitMaxz]

This is a common issue on s9 what we can do for now is software if you don't have extra miner and PSUs for troubleshooting.

Can you revert the firmware back to autofreq firmware?
Try this firmware Antminer-S9-all-201711171757-autofreq-user-Update2UBI-NF.tar.gz

then set the pool and reboot after setup the pool then run the miner for 20 minutes to warmup and let the auto tune find the optimum settings.

lets see if you get hashrate with this firmware.

[mountrover]

Thanks, just tried, got an error, Cannot Find Signature!!! when installing. Antminer-S9-all-201711171757-autofreq-user-Update2UBI-NF.tar.gz also tried s9_fix_upgrade .tar.gz same result.

What next?

[BitMaxz]

There's two option to do to bypass this error when flashing check this 2 option below.

- How to bypass ""Cannot find Signature" when updating your antminer firmware.
or make
- S9 series (S9, S9i, S9j, S9 Hydro) Control Board Program Recovery
with SD card to force the miner to flash the firmware.

[mountrover]

Hi BitMaxz,

thanks so much for the help, I have over the many months tried many different fixes, I'm still not 100% sure what went wrong, I have been able to load new firmware, but still the hasboards go quiet.

I have just bought a new s9 and are starting over.

I have a question about what is the recommended driver for new miner, I will post as a new topic.

thanks again for your great help, I know a lot more about miners now!