GekkoScience Terminus R606 750GH (up to 1TH) quiet miner, now shipping

[os2sam]

That sounds pretty good.  I wouldn't go over 750Mhz though, per sidehacks suggestion.

[sidehack]

If you're using a brick, take it easy. If you've got a decent PSU on the PCIe connector, well, just don't burn the miner up. I've had test units run almost 900MHz.

[MoparMiningLLC]

my psu is 1000w and is running 2 R606's and an Apollo pulling just around 300w

[minefarmbuy]

That sounds pretty good.  I wouldn't go over 750Mhz though, per sidehacks suggestion.

Looks like it's hashing pretty well now. tunes to 700mhz on setting 7, overall average of 821gh/s running since 7:45 PM PST last night, current hour poolside is a bit over 900gh/s.

If you're using a brick, take it easy. If you've got a decent PSU on the PCIe connector, well, just don't burn the miner up. I've had test units run almost 900MHz.

Yea, it connected to my desktop's psu. 1600W.

[nuanicaj]

That sounds pretty good.  I wouldn't go over 750Mhz though, per sidehacks suggestion.

I have 4 running on your breakout board now.   I was using a different model, all 4 ports were burnt out.   On two units the pcie ports are damaged.

[MoparMiningLLC]

@sidehack - fixable? If so, can I send to you to fix? and how much would it cost to fix? my grandson knocked it over and it hit just right that with the cord plugged in that it knocked this right off.

[sidehack]

Yeah we had so much trouble with those we started epoxying the jack to the board. Yours must be an early batch. I'll take care of it.

edit - Definitely an early batch, because we also put a notch in the case punchout to help accomodate the end of the cord and yours doesn't have that either. Your serial number must be like '1'.

[MoparMiningLLC]

Yeah we had so much trouble with those we started epoxying the jack to the board. Yours must be an early batch. I'll take care of it.

edit - Definitely an early batch, because we also put a notch in the case punchout to help accomodate the end of the cord and yours doesn't have that either. Your serial number must be like '1'.

yes, the serial number is 10040011, and yes it does not have the notch that my other R606's have.

how do I go about getting it to you?

[sidehack]

Hit me up in messages and I'll give you an address.

[minefarmbuy]

yes, the serial number is 10040011, and yes it does not have the notch that my other R606's have.

how do I go about getting it to you?

Was it a unit from us? We can shoot out a label.

[jimjam123]

Hit me up in messages and I'll give you an address.

Hey Sidehack,
I have a Terminus that is not powering up with neither the 8A or 10A.
Can I sent it to you for repair? Or is there someway I can self-diagnos?

Thanks,

[sidehack]

Probably want to talk to the guy you bought it from.

[LazyAssHoodRat]

I can't get a hash rate higher than 443ghs on TWO miners combined!!!!!   I'm running Windows CGminer 4.11.1 using a Gigabyte Brix minipc as a controller.  Each miner is plugged into it's own USB 2.0 port.  I'm getting this message from CG miner...  Plateau adjust target freq 550ghz—>200ghz I know 200 is the target frequency of Newpacs but I'm not running any on this system.

using the batch file from CG miner I added my info as:

Code:

cgminer.exe -o stratum+tcp://stratum.slushpool.com:3333 --suggest-diff 128 -u GhettoSupstar.BlockStar -p x1234 --gekko-r606-freq 550

Any Ideas what would cause this?

[sidehack]

What's the voltage level set at? All 12 chips detected on both miners?

[LazyAssHoodRat]

Both units are on setting 4 with only the top light.  430mv CG miner shows 12+ chips there's no defective chips in either unit.  It's running at 200mhz.

[sidehack]

Then the problem is your controller. If you're running Windows it probably sucks. Might check through the logs here and see what other Windows builds and flags you might test with.

[419mining]

If you running on Windows and not getting a stable hashrate, I would add the gekko lowboost flag, check the first post for reference.

[nuanicaj]

Yeah we had so much trouble with those we started epoxying the jack to the board. Yours must be an early batch. I'll take care of it.

edit - Definitely an early batch, because we also put a notch in the case punchout to help accomodate the end of the cord and yours doesn't have that either. Your serial number must be like '1'.

I have 2 burned PCIe ports.  I need to ship to you for repair.

[madbiker2]

hello. i am from spain? were i can buy it? i was to make a preorder in bitcoinmerch, they are legal? thanks.

[HagssFIN]

@madbiker2
See www.bitshopper.de , he is in Germany and he is a trusted GekkoScience reseller.